Pile Integrity Tester Dealers

• Application: By using the reflected wave method, the instrument is used to assess the integrity of concrete pile
• Brand Name: ZBL
• Power Source: Lithium battery
• Capacity: >144(dB)
• Frequency: 1-10K(Hz)
• Display: PDA With sunlight viewable touch screen display

• Weight: 5 Kg (11 lbs.)
• Model No.: PDA-8G
• Display Type: Digital
• Grade: Automatic
• Condition: New
• Size: 320 X 250 X 68 mm (12.6 x 9.8 x 2.7 inches)
• Temperature range: 0 to 40 DegreeC (32 to 104 Degree F) operating; -20 to 65 DegreeC (-4 to 149 Degree F) storage
• Power:  100-240 VAC
• Charging time: 6-hour maximum

• Manufacturer: : PDI
• Model: PIT-V,PIT-FV

PIT performs Low Strain integrity testing, also called Sonic Echo or Pulse Echo Testing. The PIT may be used for auger cast-in-place (CFA) piles, drilled shafts, driven concrete piles, concrete filled pipes and timber piles. It detects potentially dangerous defects such as major cracks, necking, soil inclusions or voids and, in some situations, can determine unknown lengths of piles that support existing bridges or towers. PIT data is evaluated in the field or transferred to a personal computer for further analysis by the PIT-W software. The lightweight PIT unit is operated by one person, has an easy-to-use touch screen, and runs an entire day on its internal rechargeable battery. The PIT test consists of attaching an accelerometer to the top or side of the foundation to be tested. The accelerometer acquires data resulting from the impact of a small hand held hammer (instrumented or not). If a defect is present along the shaft, its size and location can be estimated by analyzing the propagation and reflection of the wave induced on the foundation by the hammer impact. It is also possible to estimate the depth of the pile toe.

• Brand Name: SolGeo
• Temperature: 0-60 DegreeC
• Pulse Duration: Selectable,1 to 65000 us
• Voltage Out Transmitter: Selectable,100V to 1200V
• Transmitter Pulse Repetition: > 20 misure/second
• Recharging Time: 4h
• IP Rating: IP 65
• Autonomy: 0.8W Standby / 1.6W Ultrasonic active
• Travel Time Resolution: 100 ns
• Converter Type: 2 A/D x 12 bit converter
• Channel: 2 input / 1 transmitter
• Amplifier: 1 to 1024 software selectable
• Sample per Event: 1K to 8K for channel
• Bandwidth: > 1 MHz

Provide a Pile Integrity Tester (PIT) or an equivalent equipment. The equipment shall have the following minimum requirementsThe analog to digital resolution shall be at least 24 bits. • The sampling frequency shall be at least 25,000 Hz. • Data shall be stored such that additional processing or further wave analysis is possible.

• Screen Type: Color Lcd Display
• Usage: Dynamic Pile Testing

PIT performs Low Strain integrity testing, also called Sonic Echo or Pulse Echo Testing. The PIT may be used for auger cast-in-place (CFA) piles, drilled shafts, driven concrete piles, concrete filled pipes and timber piles.

Pile integrity test is used to assess the continuity of piles. With this test, necking or bulging and uniformity of quality of concrete is checked.Piles that are doubtful for integrity are taken up for Dynamic load testing along with some piles which are ok. Method of Testing : There are Indian Standards for the pile integrity test & the most commonly used worldwide is Pile Integrity Test as per ASTM – D 5882 – 00, “Standard Test Method for Low Strain Integrity Testing of Piles”. Relevant clause from the said ASTM standard is reproduced below: Clause no. 5.2.3 : Placement of Transducers – The motion sensor should be placed at or near the pile head using a suitable, or temporary, bonding material (that is wax, vaseline etc.) so that it is assured that it correctly measures the axial pile motion. The motion sensor is placed generally near the center of pile. Additional locations should be consi...

Our organization is involved in providing a qualitative Pile Integrity Tester to our customer. These test are performed by pulse echo or Transient Response Method used to test piles integral in the structure. Pile Integrity Tester is available in several configuration to meet the needs of the customer. It provide high quality services to our esteemed clients.

• Power Source: Electric
• Weight: 1.36 kg
• Capacity: Up to 100 piles/hours
• Usage: Industrial
• Accuracy: 0.05 %

• Weight: 1.24Kg
• Product Model: VS-P800
• System Noise Voltage: Less than 2 mV
• Dynamic range: More than 138dB
• Amplifier Band: 10Hz-10kHz
• A/D Resolution: 16-bit A/D
• Sampling time interval: 2us-32768us
• Sampling Length: 1024, 2048, 4096
• Time indication error: Less than 1%
• Channel Number: One
• Amplification factor: 1-128
• Data transmission mode: Wireless Cloud Transport (Options)
• Trigger mode: Signal triggering
• Sensor Sensitivity: 100 mV/g
• Sensor frequency band: 1-10000Hz
• Continuous working hours: More than 10 hours
• Power Supply: Built-in rechargeable lithium battery (+7.4V)
• Display: 640*480 Capacitance Screen
• Operational mode: Touch
• Size: 220x160x50

pile integrity tester, Rebound Hammer, rebar detector, analyzer

pile integrity tester, Ultrasonic Pulse Velocity Tester

pile integrity tester, cement testing, pile testing

pile integrity tester

pile integrity tester, Bond Testers, High Strain Dynamic Pile Load Tester

pile integrity tester, Plate Load Test

pile integrity tester, Resistivity Testing, predictive maintenance service