Pneumatic Ply Bond Tester
225,000 Per Piece
1 Piece (MOQ)
Description: Our Internal Ply Bond Tester is designed for determining the Internal Bonding Strength of Paper, Paperboard and Laminates, by measuring the average energy, in thousands of foot pound required to delaminate the specimen in two piles, as described by the TAPPI Routine Control Method RC-308. It is made of heavy cast iron base with built-in leveling device pressure senditive tape dispenser intergral with base. It works with Pneumatic Air supply for auto clamping of samples through air pressure. It is newly made upgraded model which saves time and gives more accuracy for samples.
Servo Pneumatic Fatigue tester
Get Price Quote
Servo Pneumatic Actuator : The Servo Pneumatic Actuator shall be 1 KN capacity max. with anti rotational fixture and displacement sensor for displacement measurement of actuator during testing. Pneumatic Power Pack: The system shall be operated @ max. 6 Bar . All the necessary pre filter and lubricators shall be pre-plumbed. Displacement Sensor: Absolute position transducer, max. range, 100 mm Accuracy better than 0.5% of the FS. Resolution infinite. Software Suitable software for Tensile, Bending and Compression tests for fatigue and static loading as per international standards. Kalpak UTM-TEST-CP Windows based Machine control, Data Acquisition and analysis software suitable for Tensile, Bending and Compression tests for fatigue and static loading as per international standards. The software shall be able to conduct test in either programmable Load or programmable length mode. It will continue test till preset counts are reached or till preset limit condition counts are reached.
Best Deals from Pneumatic Tester
Pneumatic Pressure Tester
Get Price Quote
Construction : Made from AISI 304 SS Standard Accessories :Pointer Puller, ‘O’ Ring Set Adaptors of 1/4", 3/8” & 1/2" BSP
Pneumatic Bursting Strength Tester
Get Price Quote
1 Piece (MOQ)
BEATING & FREENESS TESTER (SR TYPE) (PNEUMATIC LIFTING MODEL)
Get Price Quote
1 Piece (MOQ)
Drop Tester i9 (Motorized, Pneumatic)
100 - 200 Per 1 Piece
1 Piece (MOQ)
A Drop Tester is perfect machine to test the endurance of the corrugated cartons. It is equipped with motorized arrangement to lift the single wing structure . The pneumatic system operates the wing structure. It has a wired remote control to operate the machine. The boxes are tested on 3ways - edge wise, corner wise and flat surface. Paramount Drop Tester i9 (Motorized, Pneumatic) is a Next Gen. Equipment designed to test the drop of heavy packages and test specimens confirming the ease and safety for operator. Drop Tester utilizes a high strength welded material drop platform. When a drop test is initiated, the drop carriage is accelerated straight down from underneath the test specimen, imparting no rotational forces and insuring a flat drop.
H6900 Series Pneumatic Dead Weight Tester
56,000 Per 1
Piston Calibrated thro’ “Cross Floating Techniques” • Calibrated to Standard Gravity (Customer specific Gravity adjustment can also be done optionally) • Accuracies Traceable to International Standards • Non-Magnetic Stainless Steel Weight Sets • Calibration Certificate – for overall Accuracy + PCU (Area) + Weights (Mass) from NABL Accredited Lab – as per ISOIEC 17025:2005
BURSTING TESTER Digital with Pneumatic holding
56,000 - 96,000 Per Piece
1 Set(s) (MOQ)
Drop Tester Motorized Pneumatic
Get Price Quote
Drop tester is widely used in different industry to test the drop strength of the corrugated packages. The machine is innovated after understanding the requirements of carton manufacturing industry. The standard operating procedure of the test is very simple. But due to human interference the test results were not accurate as expected. Thus, to eliminate the human interference, Presto has designed a drop tester. This machine is equipped with a motorised assembly and a pneumatic system for smooth functioning. The operator operates the machine with remote control. The carton specimen that is to be tested is put on the winged structure style platform. The platform is lifted to a certain height as per the test requirement or test standard. The cartons are dropped in 3 ways; flat surface, edge wise, corner wise. A remote control is used to open the wings of the platform so that box can be dropped. The box is visually observed for the damages. This machine is widely used in industry that used carton packages. Drop tester is the perfect machine to check the endurance of the boxes during storage, transit and conversion. Top edge holding device with adjustable height as per the test requirement It has twin flaps as dropping platform. It has havel grey and blue combination with zinc chromium coating for corrosion resistance. Body is made up of mild steel for increased shelf life
Pneumatic Vertical shock and Bump test System
Get Price Quote
The Pneumatic vertical shock and bump test system features an advanced design with a high degree of performance and automation.The tester is easy to use and has low maintainence requirements.This equipment is used for conventional half-sine wave,post –peak sawtooth wave,square wave,impact response spectrum function and other shock tests. Performance characteristics: The system utilizes a pneumatic drive which features a simple structure,high reliability and enviromentally friendly operation. Greatly improves continuous shock test efficiency with a maximum shock frequency of 100 times/min. Large pulse width and small overload test are easily achieved. Higher reliability and better waveform compared with electric or hydraulic driven collision tables. Shock velocity can be controlled by adjusting the air pressure. The shock DAQ series control and measurement system can be Utilized and incorporated into the system for manual shock,continous shock,single shock,interval shock and other test types. The Self-Buffering base is designed to greatly reduce transmission of the shock force into the ground and allows the system to be placed directly on the floor of any standard mechanical industrial plant
P8000 / 8600 Series Pneumatic Dead Weight Testers
Get Price Quote
We are offering pneumatic dead weight testers operating using air gas are available in several ranges from vacuum up to 35 bar pressure. Accuracy: p8000 : ±0.05% reading p8600 : ±0.025% reading
Pneumatic tester
Get Price Quote
hydraulic hand pump, test hoses and adapters, and protective hard case.Combine with any Fluke-700G Series Gauge, 1,000 psi range or greater, to make a complete pressure testing kit, Generates pressure up to 10,000 psi range or greater, to make a complete pressure testing kit,Includes 700HTH-1 hose kit and adapters for connecting to the pressure device to be tested.Hard case protects pump and gauge and allows gauge to remain connected to the pump.
Drop Tester Motorized Pneumatic
Get Price Quote
Drop tester is widely used in different industry to test the drop strength of the corrugated packages. The standard operating procedure of the test is very simple. But due to human interference the test results were not accurate as expected.
Stiffness Pneumatic Tester
Get Price Quote
Stiffness Pneumatic Tester, Light & Weather Fastness Tester, Crocking Meter
Pneumatic Bursting Strength Tester
Get Price Quote
Fuke P3000 Pneumatic Dead Weight Tester
Get Price Quote
Fuke P3000 Pneumatic Dead Weight Tester, Autonics SPC1 Series Power Controller
