Proving Rings Dealers

This is for determining the bearing capacity of sub-grade soils or for compaction control and meets the requirement of astm d-420. Consists of a sturdy handle under which is 􀁅ixed a sensitive proving ring. An extension piece is 􀁅ixed on to the bottom of the proving ring and carries the detachable penetration cone at its tip. Proving ring capacity is 130 kg and the .002 mm dial indicator is provided, indicates the penetration load applied with a sensitivity of approx. 12 kg. Division. A calibration chart is provided for the proving ring. Instrument is complete in wooden carrying case.

The proving rings are made of special steel, carefully forged to give maximum strength and machined to give high sensitivity commensurate with stability, ensuring long life and accuracy. Loading pads have female threading 12" BSF (16 tpi)..

Tension Compression Proving Rings are having standard 1/2" (BSF Threads) and for measuring tension , 2 nos. Tension rods having male threads at both ends are supplied. For measuring loads in compression these tension rods are removed and the ring can be used in usual way. Works calibration charts for tension and compression are supplied with each ring . Supplied complete with tension rods in a carrying case. Note : We can also supply the following Proving Rings. 1. Tension cum compression proving ring upto 10,000kg capacity. 2. Double proving rings.

• Material: Metal
• Capacity: 100-1000nm
• Application: Industrial
• Surface Finshing: Polished
• Resistivity: Rust Resistant
• Color: black

The company has made its mark as a Manufacturer and Supplier of Proving Rings. The Proving Rings are used for load measurements as well as in outfits of varied soil, cement, & bitumen testing equipment. Made using forged steel for maximum strength, sensitivity, and stability, the Proving Rings have a long life and amazing accuracy levels. The Proving Rings can be availed in different capacities arranging from 50-200000 KGF. The Proving Rings consist of dial gauge, plunger anvil, loading bosses, loading ball nipple and steel ball.Working : Compressive or tensile load is applied within the elastic range temporarily deforming the rings Measurement of deformation by sensitive dial gauge fixed co-axially at the center of proving ring Readings of dial gauge readings versus load applied enable operator to find out unknown load by noting dial gauge reading for unknown load High elasticity ensures retention of shape on removing load if loaded in elastic limits

We are offering proving rings. The series 200 proving ring, while similar to the series 100, has three performance-proven features which increase its accuracy. It has a larger 200-division dial, a finer-pitch micrometer screw and a greater deflection under load. As a result, its uncertainty is reduced and operator confidence is improved. Ease of use is further increased with the adjustable vernier index. Readings to 1/10 division and interpolation to 1/20 division are possible. Because the index is adjustable, the dial will actually read zero on the no-load reading. The series 200 proving rings are suggested for calibrating load cells and materials testing machines where high degree of accuracy are desired. All capacities are available in compression types and combination compression/ tension types with threaded external bosses to which pulling rods may be attached for use in tension calibrations.

Product Description   Proving rings are used for load measurements and are used in outfits of a number of Soil / Cement & Bitumen Testing Equipments like Direct Share Test Apparatus, Triaxial Shear Test Apparatus, CBR Test, Uncontained Test, and Marshall Test etc. They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy. When Compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load. The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits.

• Brand Name: Quality Engineering Corporation
• Capacity: 130 kg and .002mm
• Place of Origin: Roorkee
• Usage: Determining the bearing capacity of sub-grade soils
• Weight: 1/2 kg

We are instrumental in offering optimum quality Proving Rings. Available in different dimensions, our Proving Rings made up of quality material. They comply with ASTM D-420 industry standard. The Proving Rings are extensively used for determining the bearing capacity of sub-grade soils or for compaction control. Our rings consist of a sturdy handle under which is fixed a sensitive proving ring. An extension piece is fixed on to the bottom of the proving ring and carries the detachable penetration cone at its tip. The capacity of our Proving Rings is 130 kg and the .002 mm dial indicator is provided with it. The dial indicator indicates the penetration load applied with a sensitivity of approx. 1/2 kg. division.

• Application: Laboratory
• Automation Grade: Manual
• Body Material: Steel
• Power: Electronic
• Usage: Abrasion Tester
• Specimen: Round

• Material: Metal, Steel
• Automation Grade: Automatic
• Application: Industrial
• Capacity: 100-1000nm, 1000-2000nm, 2000-3000nm
• Packaging Type: Protective Wooden Case
• Type: Proving Rings
• Country of Origin: India

• Automation Grade: Semi-Automatic
• Brand Name: Steco
• Packaging Type: Box
• Usage: Asphalt Mixture Stability Tester
• Display Type: Analog

• Type: Proving Rings
• Material: Metal
• Certification: ISI Certified
• Application: Load Meassurements
• Capacity: 100-1000nm
• Packaging Type: Protective Wooden Case
• Automation Grade: Automatic

The Morehouse Proving Ring is recognized wherever highly accurate force measurement calibrations are preformed as the premier standard. This reputation has been earned by years of established and maintained by the National Institute of Standards and Technology. Morehouse is dedicated to the design, manufacture and application of proving rings, which can be used with confidence in standards laboratories and throughout industry. The reliability, repeatability and accuracy of Morehouse Proving Rings are unequalled and unchallenged by any other force measurement device. If you have a proving ring and want to make it easier to use while reducing error.   Morehouse can help.  We have converted lots of analogue rings with very positive results.  The digital ring reduces operator error, resulting in about a 25 - 50 % improvement in accuracy. It's terrific.

Our company is ranked among responsive and responsible Suppliers of Proving Rings, engaged in catering to buyers across varied markets. We have invested a large amount for developing all-the-in-house storage facility that is managed and maintained by our diligent professionals. Also, it keeps us free from stock-out situations.   Working : Compressive or tensile load is applied within the elastic range temporarily deforming the rings Measurement of deformation by sensitive dial gauge fixed co-axially at the center of proving ring Readings of dial gauge readings versus load applied enable operator to find out unknown load by noting dial gauge reading for unknown load High elasticity ensures retention of shape on removing load if loaded in elastic limits

• Material: SS
• Brand Name: SreeKa
• Country of Origin: Made in India
• Usage/Application: Calibration, testing instrument
• Shape: Round
• Color: Chrome

• Country of Origin: Made in India
• Material: Alloy Steel
• Automation Grade: Manual
• Pressure: 1-50Kn
• Frequency: 50 Hz or 60 Hz
• condition: NEW
• Shape: Round

• Capacity: 250 kgf. 500 kgf. 1000 kgf. 3000 kgf. 5000 kgf.

These proving rings are made out of special steel, carefully forged to give maximum strength & machined to give the highest sensitivities commensurate with high stability and to ensure long life and accuracy. All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists in rings with bolted abutments. The dial gauge and anvil are mounted on U-brackets clamped to the ring body by Allen set screws. The dial gauge is fitted with a special back cover and threaded bush which does not permit any shift from the original diametric alignment, coaxial with the loading boss centers, that is set at the factory before calibration. For all compression proving rings and tension compression proving rings up to and including 5 kN capacity (a little over 500 kgf) the loading bosses have female threading, 12" B.S.F. (16 t.p.i.) The boss faces are ground and polished and are lane parallel to within 0.02mm.total D.T.I. run-out. Caps are provided for use when loading in compression. Repeatability is as stipulated in IS : 4169-1967. The rings are supplied complete with dial gauge and our own calibration chart, packed in polished wooden boxes.

• Capacity: 500KN capacity
• Material: mild steel
• Brand Name: SISCO INDIA
• Callibration: Each ring are individually calibrated and supplied with works calibration chart and a carrying case
• Dial gauge: The dial gauge plunger rests on an adjustable anvil.
• Shape: Circular
• Color: variable
• Usage/Application: Soil/Cement & Bitumen Testing

All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists with bolted abutments.The dial gauge and anvil are mounted on U-brackets clamped to the ring body by set screws. The dial gauge is fitted with a special back cover and a threaded bush, which does not permit any shift from the original dial alignment, coaxial with the loading boss centres, that is set at the factory before calibration.For all compression proving rings and tension-compression proving rings up to and including 5 kN capacity, the loading bosses have female threading 1/2" BSF (16 tpi)   The boss faces are ground and polished and are plane parallel to within 0.02mm total DTI run-out. Tension compression rings have their integral loading bosses male threaded, 1.25" dia, 8 tpi, square thread, 1.25" long. Caps are provided for use when loading in compression.Repeatability is as stipulated in IS:4169. The rings are supplied complete with dial gauge and Works Calibration Chart, individually packed in polished wooden boxes. NPL (India)/ NCCBM Calibration/ NABL Calibration can also be arranged for any proving ring at an additional cost. Proving rings to meet special requirements are also available on request. Separate polished and ground pair of Loading Pads for Compression Proving Rings and pair of Shackles for Tension Proving Rings are provided to suit each proving ring, at extra cost and on request.

Proving rings are used for load measurements and are used in outfits of a number of Soil / Cement & Bitumen Testing Equipments like Direct Share Test Apparatus, Triaxil Share Test Apparatus, CBR Test, Unicontained Test, Marshall Test etc. They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy. When Compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load. The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits.A Dial gauge and plunger anvil are mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remote chance of shifting due to inadvertent shocks or pressures exerted on it. The dial gauge plunger rests on an adjustable anvil. Proving Rings , from 50 kg to 1,00,000kg capacity provided with 1/2 inch B.S.F female threads. Loading bosses and a loading ball nipple and steel ball are supplied with each rings. Rings of capacity over 25000kg (or 25 Tonnes) are not thus threaded. Each ring is individually calibrated and supplied with works calibration chart and a carrying case.Calibration charts from Standard Laboratories for the Proving Rings ordered are also available at extra cost.All Proving Rings are Integral Type.Integral type Compressive Proving Rings of different capacities from 50kgf to 200000kgf are available.(a) Above cap. 50 to 500kg.(b) Above cap. 500 to 3000kg.(c) Above cap. 3000 to 5000kg.(d) Above cap. 5000 to 10000 kg.(e) Above cap. 10000 to 20000 kg.(f) Above cap. 20000 to 30000kg.(g) Above cap. 30000 to 50000 kg.(h) Above cap. 50000 to 100000 kg.(i) Above cap. 100000 to 200000 kg.(j) Above cap. 200000 to 300000 kg.

These proving rings are made out of special steel, carefully forged to give maximum strength & machined to give the highest sensitivities commensurate with high stability and to ensure long life and accuracy. All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists in rings with bolted abutments. The dial gauge and anvil are mounted on U-brackets clamped to the ring body by Allen set screws. The dial gauge is fitted with a special back cover and threaded bush which does not permit any shift from the original diametric alignment, coaxial with the loading boss centers, that is set at the factory before calibration. For all compression proving rings and tension compression proving rings up to and including 5 kN capacity (a little over 500 kgf) the loading bosses have female threading, 1/2" B.S.F. (16 t.p.i.) The boss faces are ground and polished and are lane parallel to within 0.02mm.total D.T.I. run-out. Caps are provided for use when loading in compression. Repeatability is as stipulated in IS : 4169-1967. The rings are supplied complete with dial gauge and our own calibration chart, packed in polished wooden boxes.

Proving rings are used for load measurements and are used in outfits of a number of Soil / Cement & Bitumen Testing Equipments like Direct Share Test Apparatus, Triaxil Share Test Apparatus, CBR Test, Unicontained Test, Marshall Test etc. They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy. When Compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load. The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits.A Dial gauge and plunger anvil are mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remote chance of shifting due to inadvertent shocks or pressures exerted on it. The dial gauge plunger rests on an adjustable anvil. Proving Rings , from 50 kg to 1,00,000kg capacity provided with 1/2 inch B.S.F female threads. Loading bosses and a loading ball nipple and steel ball are supplied with each rings. Rings of capacity over 25000kg (or 25 Tonnes) are not thus threaded. Each ring is individually calibrated and supplied with works calibration chart and a carrying case.

• Capacity: 25kgf to 100kgf (1KN), 200kgf (2KN), 250kgf (2.5KN), 1000kgf (10KN), 2000kgf (20KN) etc.

The Proving Rings are made of special steel, carefully forged to provide high and stable accuracy, dependability and repeatability. The dial gauge and anvil are mounted on U-brackets clamped to the ring body by set screws. The indicator has a sensitivity of 0.002mm div and the deflection is directly proportional to the applied load. The rings are supplied complete with dial gauge and Works Calibration Chart, individually packed in polished wooden boxes. NPL (India) NCCBM Calibration Certificates can also be arranged for any proving ring at an additional cost. Separate Pair of Loading Pads are provided to suit each proving ring.

This is for determining the bearing capacity of sub-grade soils or for compaction control and meets the requirement of ASTM D-420. Consists of a sturdy handle under which is fixed a sensitive proving ring. An extension piece is fixed on to the bottom of the proving ring and carries the detachable penetration cone at its tip. Proving ring capacity is 130 kg and the .002 mm dial indicator is provided, indicates the penetration load applied with a sensitivity of approx. 1/2 kg. division. A calibration chart is provided for the proving ring. Instrument is complete in wooden carrying case.

• Automation Grade: Manual
• Brand Name: Smarcon
• Country of Origin: Made in India
• Usage/Application: Tension Compression Proving Ring
• Finishing: Crome

The calibration standard against which all others are measured. Throughout the world in industry and standards laboratories, t The calibration standard against which all others are measured. Throughout the world in The calibration standard against which all others are measured. Throughout the world in industry and standards laboratories, the Morehouse Proving Ring is recognized for it's lasting reputation of unquestionable accuracy in the measurement of mechanical forces. For this reason, it is accepted as a prominent standard for the calibration of testing machines, torque measuring dynamometers, thrust standards, electronic and hydraulic load cells, and many other force measuring devices and systems. and standards laboratories, the Morehouse Proving Ring is recognized for it's lasting reputation of unquestionable accuracy in the measurement of mechanical forces. For this reason, it is accepted as a prominent standard for the calibration of testing machines, torque measuring dynamometers, thrust standards, electronic and hydraulic load cells, and many other force measuring devices and systems. he Morehouse Proving Ring is recognized for it's lasting reputation of unquestionable accuracy in the measurement of mechanical forces. For this reason, it is accepted as a prominent standard for the calibration of testing machines, torque measuring dynamometers, thrust standards, electronic and hydraulic load cells, and many other force measuring devices and systems.

Proving Rings, Compression Proving Rings (AIM 261 TO AIM 281), Tension Proving Rings (AIM 290 To AIM 298) & Tension Compression Proving Ring (AIM 284)   The Proving Rings are made up of special steel, carefully forged to give maximum strength and machined to give high sensitivity commensurate with stability, ensuring long life and accuracy.All proving rings are integral type viz. the loading (outside) bosses are forged integral with the ring body. This ensures that there is no possibility of abutment shift and consequent loss of accuracy in reading that always exists with bolted abutments. Repeatability in these Proving Rings is as stipulated in IS:4169. The rings are supplied complete with dial gauge and Works Calibration Chart, individually packed in polished wooden boxes. National Physical Laboratory (NPL), (India)/ National Council for Cement & Building Material (NCCBM )Calibration can also be arranged for any proving ring at an additional cost. Proving rings to meet special requirements are also available on request.Separate polished and ground pair of Loading Pads for Compression Proving Rings and pair of Shackles for Tension Proving Rings are provided to suit each proving ring.We supply Compression Proving Rings, Tension Proving Rings & Tension Compression Proving Ring of different capacities.   Application Compression and Tension Measurements Industry Chemical/Process Agricultural Civil Infrastructure Dams & Tunnels Geophysical/ Seismology Testing Geotechnical (soil/ rock) Testing Irrigation Mining Real Estate Roads, Highways & Bridges Education Architecture Building Technology Civil Department Geotechnical Mining Engineering Science Colleges Traffic & Transportation Railways Roads, Highways & Bridges