Vertical Glandless Pump Dealers

Applications: Scrubbers Filter press Ejector systems Effluent transfer Phosphoric acid plants Gas washing plants Caustic soda plant Principle Of Glandless Pump The Vertical Glandless Pump in normal hydraulic terms does not differ from any conventional centrifugal pump. The pump is designed in such a way that the liquid which normally try to pass through the point, where the impeller drive shaft enters the back plate (stuffing box) is diverted and returned as a controlled flow to the suction tank. The need for any seal is eliminated by allowing the leakage liquid to escape through the Overflow connection of the Overflow Chamber. The liquid entering suction flow around the impeller casing and leaves through the delivery under pressure. Between the annular gap of upper rotor casing and impeller some leakage liquid escapes to the Overflow Chamber. The auxiliary impeller (expeller) prevents the leakage liquid going further up and canalizes it through out – Irt in the Chamber.        Advantages: No shaft sealing arrangement so no maintenance. Pump can run dry, Effectively handles slurry / sludge. The pump suffers no ill effect if the pump discharge valve is partially or fully closed.   

“mvgp” pumps are vertical molded polypropylene corrosion resistant pumps.pumps for leakproof and maintenance free pumping of corrosive and abrasive liquids.   principal of vertical glandless pump the “malhar” pump is similar hydraulic design to any conventional centrifugal pump. It differs in so far as it is always mounted in the vertical position. A restriction is provided above the impeller and need for any from of liquid seal is obylated by allowing a small leakage to escape by way of an overflow connection in the upper pump body return to suction vessel. the most suitable method of installation will depend on the pumping application. The simplest and most widely adopted method is mount the pump close to the feed tank at such a level that the impeller is flooded and the pump therefore pumped when the liquid reaches a certain height in the tank.the pump will deliver liquid until the suction pipe becomes uncovered , when it will run dry until the liquid level is restored to the point where re-printing can take place,this cycle of operation may be repeated indefinitely. Contact vertical glandless pump supplier, vertical glandless pump manufacturer today. The vertical glandless pump  is vertical molded polypropylene corrosion resistant pumps.pumps for leakproof and maintenance free pumping of corrosive and abrasive liquids.   operation advantages of glandless pump • the recognizable leading improvement is the deletion of problems get to your feet from the use of powered seal, insulation box and inside bearing. • the aptitude of pump to run dry eliminates single reason of interruption which is regularly attributable to the human component this feature is very convenient in process needing continuous transference of a corrosive fluid with a high gradation of reliability e.g. Disposal of acid effluent. • the glandless pumps lend itself to process incorporating automatic control of a pump discharge valve. The “controlled leakage” acts as an integral by-pass. The pump suffers no ill effects if the discharge valve is partially or fully closed. • the maximum main improvements to be derivative from the use of glandless pump are in the province of maintenance and following reduction in down time invention victims. Normal maintenance on the glandless pump is confined to lubrication of the driving.   sailent features of vertical glandless pump • no mechanical seal, stuffing box and internal bearings provided. • no maintenance since the pump can even run dry indefinitely as there is no packing, bushes or internal bearings. • reduction of downtime production losses in view of above features. • all the wet-end parts are in solid molded construction to with stand corrosion and erosion. • the impeller is semi-open type used in our all-vertical pumps to suit both clear and polluted fluids. • pump mounted outside the suction tank and is not submerged type. • polypropylene are manufactured by solid injection molding process with high pressure hence.   temperature resistance • pp 50º to 80 º c • pph 90 º to 100 ºc • pvdf 100º to 115ºc   range of performance • because glandless pumps do not have any packing bush or internal bearing, full advantage can be taken of available drive speeds. The pump may be run at 1450 and 2900 rpm respectively and a range of impeller diameter for each pump size gives a wide spread of performance. • in general the range cover flow up to 100m3/hr. And discharge head up to 50 meters.

• Type: Vertical Sealless Glandless Pump
• Shape: Vertical
• Color: White
• Fuel: Electric
• Condition: New
• Automatic Grade: Manual
• Power: 7-9kw
• Pressure: 0-10bar
• Warranty: 1 Year

vertical seal less gland less non-metallic centrifugal pump application :- scrubber application , acidic slurry transfer pump , etching liquid transfer pump , chemical circulation moc available :- pp , pe , ptfe application salient feature :- no magnet , no mechanical seal , no gland dry running particle handle - 1mm less rotating parts .

• Shape: Vertical
• Application: Ground Water Supply
• Voltage: 110V
• Power: 1-3kw
• Pressure: 10-20bar
• temperature capability from: 270 oC to 70oC

Vertical Glandless Pumps are offered without Stuffing Box and Seals & Bearings. These Vertical Glandless Pumps are designed as per the industrial standards for quality. The ground-breaking design of this Vertical Glandless Pump helps in ensuring hassle-free operations. Also, such a design of this Vertical Glandless Pump makes it leak-proof and easy to maintain. This Vertical Glandless Pump is manufactured using the materials and components that are resistant to abrasive as well as corrosive fluids. Principle veritical Glandless Pumps : The Fluidmatic Vertical Glandless Pump is similar in hydraulic design to any conventional centrifugal pump. The design is such that the need for any form of mechanical seal, packed gland, internal bearings, stuffing box is eliminated by allowing a controlled leakage of the liquid being pumped to return to the suction tank by way of an overflow connection in the upper body of the pump. The most widely used method of installing a glandless pump is to mount the pump in the vertical position beside the feed tank and positioned so that the pump impeller is flooded at normal maximum liquid level in the vessel the pump therefore primed. When the pump is started up it will deliver liquid until the suction pipe becomes uncovered when it can be allowed to run dry until the liquid leved is restored to the point where re-priming can take place. This cycle of operation may be repeated indefinitely. Advantages of Vertical Glandless Pumps : The ability of Fluidatic glandless pumps to run completely dry without ill effect is used will advantage in applications requiring the continuous transfer of corrosive liquids, with a high degree of reliability. Hence removes once cause of breakdown which is often attributable to the human element. The most important gains to be derived from the use of glandless pumps are in the sphere of maintenance and the consequent reduction in down-time production losses. Normal maintenance on the Fluidmatic glandless pump is confined to lubrication of the driving motor bearings. The majority of applications for which the pump is used, involve continuous circulation, for example gas scrubbers and heat exchanger circulating pumps, disposal of acid effiuent. Material Characteristics : Superiority of Pe-Uhmw over Conventional Materials All watted parts of these pumps are pressure-cast in solid sturdy construction in pe-uhmw the versatile engineering thermoplastic exhibiting superior properties such as self lubricating, very low coefficient of friction, almost zero moisture absorption, fatigue resistance, excellent chemical and corrosion resistance, lightweight, wide service temperature capability from 270 oC to 70oC. However at higher temperatures up to 90oC it shows remarkable stability and Fluidmatic pumps can be used up to this temperature for continuous service, though its resistance to wear due to slurry pumping is affected. The high molecular weight gives increase in wear resistance, increase in impact strength, dimensional stability under heat, energy absorption capacity at high loading rates, melt viscosity hence stiffer flow properties. Pe-Uhmw shows remarkable resistance for wide range of chemicals exhibits exceptional abrasion resistance comparable to Ni-Hard, Hv-9A , Si-Iron, Alloy-20, hastelloy and far outwears stainless steel, rubber, polypropylene or any other polymers in handling highly abrasive slurries. Some of Its Typical Applications to date : H3 P04, 18% - 24% H2 Sif6 with 5% - 7% silica, H2SO4 , HF and their mixutres with or without solid (Gypsum) up to 40% conc. Replaces hv-9A, alloy-20 & Si-iron. Chorinated brine, Conc. Hci, 60% - 70% H2SO4 at 80 oC. Scrubbed liquids containing F, Ci, So2, Ammonia gases etc. With solids. Replaces Hastelloy. Spin Bath solutions ( H2SO4, Znso4, Na2 So4 etc.) Carbide Sludge with sand, 40% Tio2 Slurry, Alcohol with 5% gypsum slurry etc, Acidic effiuents sludge containing cell brine, phosphoric acid sand and phosphates Other applications are in metal refineries, pickling installations, paper & Fertilizer plants, Cement plants, sugar plants, in fact all Chemical process industries. Range of Performance : Because Fluidmatic Vertical Glandless pumps do not have any packing, bushes or internal bearings, full advantage can be taken of available drive speed. The pump can run at 1450 and 2900 RPM. Respectively and a range of impeller diameters for each pump sizes gives wide spread of performance. In general the range covers flows up to 300M3 /hr. And discharge up to 60 meters. Applications of Pe-Uhmw Material in other industries : Textile Industry : For pickers, lug straps, picking caps, shuttle keys, etc. Engineering industry : Gears, Rollers, snow Mobile sprockets, Guide bars, non Abrasive strips, etc. Food Industry : Screw conveyours for pulps & fruit purees, conveyors units & guide & reversing rollers for filling and labeling machines, piping in food and beverage industry Coal & Mining : Lining of conveying machinery, chute, vibrators, air separators, coal bunkers, etc. Ship Building / Port : Cargo- hold lining, fenders Slurry transport : Transportation of sand and slurries through pipelines Electroplating : Fittings, bellows, plating drums, gear wheel, Beaing shells guide rollers, etc. Electrical Industry : Insulating components for high & very high frequencies Download

• Country of Origin: India
• Pressure: 5 Kg/Cm2 Max.
• MOC: UHMWPE
• Flow: 45 m3/hr. Max.
• Temperature: 100° C.
• Speed: 3000 RPM Max

Zero maintenance pumps, eliminate the need for gland Packing and seal. Leakproof and can run dry without damage of rotating parts. Pumps to be mounted outside the suction tank vertical position and not to be submerged. Vertical Glandless Pumps, similar in hydraulic design to any conventional centrifugal pumps, it differs in, so far as a restriction is provided, escape by way of an overflow Connection in the upper pump body & return to the suction line. Preferred selection for E.T.P.Plant because of seal-less design & can run dry. Low maintenance cost & makes maintenance easy.

Vertical Glandless pumps are best suited for any recirculation application (scrubbers for flue gas desulphurisation, Tail Gas treatment, toxic gas removal; acid recirculation in pickling lines, anodizing & electroplating units, fine slurry spray systems etc). These are also ideal for lifting raw chemical effluents (any pH & with solid particles) from the pits (priming pot eliminates the need for a problematic foot-valve system). Keep environment clean by scrubbing almost any gas. No mechanical seal or gland packing. Leak-proof pumping of corrosive & abrasive fluids acids, alkalies, effluents, solvents. Continuous running with no maintenance hassles. Dry Running? No Problem! Mounted outside suction tank - Easy to handle.     We offer the pump with priming pot arrangement instead of foot-valve. Such applications are being successfully operated at several plants. Thus what you achieve is leakless pumping with no maintenance headaches associated with foot-valves. The unique design of the pump with priming tank offers following unmatched advantages over a vertical submersible or horizontal centrifugal pump: Outside mounting makes the pump easily accessible for operation and maintenance. There is thus no need to dismantle the whole system when a part has to be replaced or any other minor maintenance job is to be carried out. Positive suction so provided renders the pumps useful in lifting liquids from 5M depths. Current Range: Capacity to 600 M3/H, Head to 80 M.

• Temperature: PPH 90 º TO 100 ºC.

The aptitude of pump to run dry eliminates single reason of interruption which is regularly attributable to the human component this feature is very convenient in process needing continuous transference of a corrosive fluid with a high gradation of reliability e.g. Disposal of acid effluent.No maintenance since the pump can even run dry indefinitely as there is no packing, bushes or internal Bearings. Polypropylene are manufactured by solid injection molding process with high pressure hence.

• temperature range: 20° C to 80° C
• Capacity: 3m³/hr to 800 m³/hr

The vertical glandless pump is a centrifugal pump and as the name suggests, this does not have any gland and or mechanical seal arrangement. The vertical glandless pump is for all practical purpose called the zero leakage pump. Hence all toxic and corrosive liquids can be handled without any leakage.

• Capacity: 250 m3 / hr.

Glandless pump:- is designed vertically. Liquid from the suction line passes through impeller to the discharge line with the required flow and head pressure. While excess liquid enter the rear plate cover €“ and is diverted back to the mothertank through overflow outlet arrangements. Hence, the design ensures total solution of leakage problem. The motor assembly is also protected against damages due to leakage of liquid. Glandless pumps ensures ensures excellent performance while handling corrosive and hazardous chemicals.

• Type: Vertical Glandless Pump
• Shape: Vertical
• Application: Ground Water Supply
• Color: Blue, Green, Grey, Red, White, Yellow
• Voltage: 110V, 220V, 380V
• Fuel: Electric
• Condition: New, Used
• Automatic Grade: Automatic, Fully Automatic, Manual
• Power: 1-3kw, 3-5kw, 5-7kw, 7-9kw
• Pressure: 0-10bar, 10-20bar, 20-30bar, 30-40bar
• Warranty: 1 Year, 2 Years

Raw material that is sourced from the reliable places is used as input in the production procedure. In order to make high quality range of products, we check it for quality prior to sourcing. We have a well-maintained and spacious storage space and thus, we are flexible enough of meeting the urgent needs. Furthermore, we by no means go out of stock and thus we maintain year round accessibility of all the products.   Application :Sp-Vgp pumps are used for continuous operations like : Scrubbing ETP Liquid Transfer Acidic Slurry Filtration

VGP - Series Pumps (Vertical Glandless/Sealless Pumps) M.O.C - U.H.M.W. -P.E. The V.G.P.Series pumps in normal hydraulic terms does not differ from any conventional centrifugal pump.The pump is designed in such a way that the liquid which would normally try to pass through the point, where the impeller drive shaft enters the backplate(stuffing box) is diverted and returnet as a controlled flow to the suction tank.The need for any seal is eliminated by allowing the leakage liquid to escape through the Overflow connection of the overflow chamber. The liquid entering suction flow around the impeller casing and leaves through the delivery under pressure. Between the annular gap of upper rotor casing and impeller some leakage liquid escapes to the overflow chamber. The auxiliary impeller (expeller)prevents the leakage liquid going further up and canalises it through out -lrt in the overflow chamber. These pumps are ideally suited for continuous operation and for all scrubbing application.The pumps always work with a negative suction.

• Features: No mechanical seal, stuffing box and internal bearings provided.

We bring forth wide-range of Vertical Glandless Pumps, which has a finest performance, reliable, corrosion resistance. Our company is widely recognized in the industry for our suitable supplies of the quantities. It is always been installed in the vertical position.Bhagwati Engineering is manufacturer of Vertical Glandless Pumps in India. The design of Vertical Glandless Pump is such that the requirement for any form of motorized seal or chock-a-block gland is eradicated by allocating a controlled leakage of the liquid that is being pumped to return to the suction tank by the route of an overflow connection in the upper body of the vertical glandless pump.

We offer vertical Glandless Seal less Pump (P.P.-VPL And VPH Type) that is designed according to well known successful two pipe principle, chemical process pump of polypropylene (plastic) material.