Vertical Sump Pump Dealers

vertical centrifugal process pump can be used in any installation or specially where the saving of space is important factor and most important where liquid is difficult to lift because of nature like temp , corrosiveness etc these pump are designed for use where the liquid handled to be is of highly corrosive nature or where non – adherence of product or zero metallic contamination is must these pumps are equally ideal for continuous or intermittent service for handling corrosive as well as ultra pure chemicals without fear of corrosion or contamination. high temperature services : maximum working temperature is 110 c / 200 c. length : pumps lengths available from 1’ to 12’ with flow rate up to 50m3/h or 120 meter head. Higher capacities and head available on request and even multistage pump can be also made . models : available in conventional or tailor-made configuration. Several models such as suction extension with float switch, duplex pumping station with float switch (auto on/off device) also available.   special features • bearing free design for handling abrasives in solutions. • motors are flange mounted single or three phase tefc from 1 hp to 100 hp . • epoxy / polyurethane paints are used on metallic bearing housing. • radial vanes on backside of impeller increase flow or fluids through the sleeve bearing preventing overflow at top of column. • lubrication of bearings by product itself or by fresh water. • all models operate at 1450 rpm / 2900 rpm (variable speed motor available ) • specially designed vapor seal provided to protect bearing from corrosive fumes • dynamically balanced impeller.   application fields these pumps are in extensive use in the fields of • pollution control. • filtration . • transferring corrosive chemicals . • slurries . • bio gas plants. • sewage. • waste water treatment plant. • phosphoric acid plant. h,po,h2sifs,h2so4,hf and . their mixtures. • gas washing plant . • scrubbed liquids containing , f,cl,so2,ammonia • water treatment plant . • any types of acidic water lifting . • m.s vertical pump are used for transfer of sulphuric acid 98 %. Olum,cloto,neptha   advantages of vertical submerged pump • no mechanical seal or stuffing box required • construction withstand corrosion & erosion • no foot valve required to lift from negative suction • no leakages problem just like gland or mechanical seal • normal maintenance • easy alignment    

• Capacity: Upto 200 m3/hr
• Motor Horse Power: 20 - 140 HP

• Application: Industrial

Are you looking for one of the preeminent Vertical Sump Pump Manufacturers in Saharanpur, Uttar Pradesh? Vikas Pump is undoubtedly the company you can stop by. With extensive years of industry experience and expertise, we have built our reputation in the domain. Our Vertical Pump are highly innovative and suitable for multiple applications. Whether you want to buy different types of Industrial Pumps, Sewage Treatment Plants or Conveyor Chains or else, we have got the best range in our portfolio to cater to the distinct needs of customers. We manufacture our Sump Pump following defined industry norms and assure you of their performance and high quality.

• Brand Name: Golds Pumps
• Country of Origin: Hubli
• Type: Chemical Vertical Sump Pump
• Capacity: Up to 750 m3/hr
• Head: Up to 60 m
• Temp.: Up to 260oC
• Depth of submergence: Up to 1500mm
• MOC: CI, CS, AISI-304/316/321/347/304L/316L, CD4MCu, CN7M, HASTELLOY-B/C, R-55, ALUMINUM, etc.

We offer Cantilever Design Chemical Vertical Sump Pump, which have semi open impeller, radially split casing, suitable to mount mechanical seal, and flanges to class 150FF. Avail Chemical Vertical Sump Pump at market leading price. Specifications Capacity : Up to 750 m3/hrHead : Up to 60 mTemp. : Up to 260oCDepth of submergence: Up to 1500mmMOC : CI, CS, AISI-304/316/321/347/304L/316L, CD4MCu, CN7M, HASTELLOY-B/C, R-55, ALUMINUM, etc.

Process sum pump (KPDS )OverviewKirloskar KPDS is sump pump for process application. It has wide range of application in various chemical process industries for pit depth upto 5.5 metre.Applications Petrochemicals, Refinery, Fertilizer and Power Industries Transfer and circulation of acids, alkalis, solvent oil etc Highly alkaline and highly acidic liquids (with enclosed impeller) Crystallizing liquids, liquids containing suspended solids, industrial clear effluent. Specifications Delivery size from 20 mm to 150 mm Capacity 0.5 to 560 m2/hr Head 2.3 m to 150 m Pit Depth up to 5.5 m Temperature (-) 10oC to 150oC Solid handling sum pump ( SHS )OverviewKirloskar SHS is sump pump for solid handling application. It is suitable for pit depth upto 9 metre.Applications Liquids with solids in suspension Sludes & pulpy material Industrial waste handling Liquid containing fibrous & powdered material Coal tar Effluent Specifications Delivery size 50 to 300 mm Capacity Head Pit Depth up to 9 m

• Pump Size: 25 mm. to 350 mm
• Discharge: 2 to 1400 m3/hr.
• Permissible Solid: 5 to 150 mm.

The easier automatic operation of the pump is possible with the use of the float switch or automatic level control unit. The pump is available in oil, grease and water lubrication system.

• Size: 25 mm to 125 mm

We manufactured vertical pumps for the applications with low net positive suction head, cryogenic temperatures where vertical lift is required and in also in sump and cooling water services. Our vertical pumps is specially designed for service in water, chemicals, sewage and slurries. Vertical pumps are cover a wide range of hydraulic condition to meet virtually every pumping service in the industry and optimum efficiency.

• Pressure: 25 bar (365 psi)
• Color: Grey
• Flows to: 1400 m3/h (6160 US gpm)
• Heads to: 250 m (820 ft)
• Temperatures: -40°C (-40°F) to 350°C (660°F)
• Speed: 4700 rpm

API 610 ConfigurationThe Flowserve CPXV vertical sump pump is also available in an optional API 610 compliant model, specifically engineered for the hydrocarbon and petrochemical processing industries. Rectangular or circular soleplates are standard. A full ANSI 150/300 lb RF soleplate is optional.Standards ComplianceThe CPXV is CE marked and compliant with applicable European directives, such as ATEX.Modular Construction ensures installation flexibility with a standard column length of 0.5 m (1.6 ft), which equates to a minimum sump depth of 0.7 m (2.3 ft) Additional Column Lengths are provided up to a maximum of 10 m (32 ft) Heavy-Duty Thrust Bearings with axial adjustment made at soleplate level Recessed Impeller version is available for enhanced solids handling capability. Suction Strainer optional Fully Jacketed version is available for molten sulfur applications.

• Capaicty: Up to 300 M3/hr
• Head: Up to 35 mtr
• Discharge Size: Dn 25 to 125 mm
• Temperature: Up to 50c
• Speed: Up to 2900 rpm

• Brand Name: PP Vertical Sump Pump

We offer pp vertical sump pump. Being a well name in the industries, we are engaged in manufacturing, exporting and supplying a distinguished range of pp vertical sump pump. Our offered pumps are intricately designed under the vigilance of skilled professionals using quality tested raw material and sophisticated technology in line with the international quality standards. Clients can avail this range in various designs, shapes and sizes at market leading price within given period of time. features: smooth finish unique look innovative design

• Brand Name: BIMM
• Condition: New
• Automatic Grade: Fully Automatic
• Power: 1-3kw
• Application: PPUMP CONTROLLER
• Voltage: 220V

Operation of Timer based Direct ON Sump pump controller for sump tank and OH tank ·         Fully automatic water level controller connecting sump tank and over head tank maintaining  full OH tank as long as  water available in the sump ·         1 sensor will be put at OH tank at 90% (High)  just below overflow level ·         2 more sensors will be put in sump tank at 10 % just above suction  head called low   and  at 20% called high levels ·         Pump starts  in timer  mode when water is available above 20% in the  sump and OH tank is not Full. Pump runs for the preset ON time OR  stops when water reaches Full before preset ON time. ·         Pump goes to OFF for the preset OFF time ·         Pump also stops if water falls below low sensor in the sump as preventive dry run protection. ·         Pump does not start after preset OFF time if water is not above  2 sensors in the sump ·         Pump  will not start if any of the 3 sensor wires  is broken ·         No airlock or dry RUN since pump stops before water falls below suction ·         It comes with Micro controller Technology, maintenance free magnetic sensors, FR4 doubled sided 1.6mm PCB with green mask and 70 micron thick copper tracks. ·         12 months warranty, direct from manufacturer including controller and sensors  

All SB Vertical Sump pumps are designed specifically for wide applications and use and feature robust design with ease of maintenance. The SB - VSP sump pump range is one of the strongest, toughest and most reliable pumps in the market. The SB - VSP pumps are easy to install, The materials used are the very best available, providing both excellent wear properties and corrosion resistance. Wear parts are available in a variety of different materials and fully interchangeable. Semi-open, vortex, fully recessed vortex and closed impellers are available to suit your pumping needs. The wet-end parts are designed for the toughest applications and the longest wear life. The single volute and generous solids passages through the pump ensure a safe and clogless operation. The wet-end assembly is suspended from a tubular column below the bearing housing. Standard pumps are supplied with wide choice of material.

• Item Code: V-S
• Immersion length: 400-2500mm at 1440 rpm, 400-1800mm at 2900 rpm
• Capacity range: Up to 150 m cubic/hour
• Head range: Up to 60 mt.

We offer a wide range of Vertical Sealless Sump Pumps that are designed in accordance with the well known two pipe principle. These are provided with shaft guide bearing bush to ensure a continuous pumping of abrasive & corrosive fluids. We offer these in varied dimensions as per the requirements of the clients. The vertical sealles sump pumps offered by us are used for pumping both chemical and industrial fluids in various sectors.  Some of the specifications of these vertical pumps are mentioned below:

• Application: Ground Water Supply
• Color: All Color
• Condition: New
• Pressure: 0-10bar, 10-20bar, 20-30bar, 30-40bar
• Warranty: 5 Years
• HP Range: 0.5 HP to 2 HP

Buy a range of flawless Vertical Sump Pumps at cost-effective prices from us! We work at full throttle to serve the countrywide market with high-performance Vertical Sump Pumps. We are reputed to be among the notable Manufacturers and Suppliers of Vertical Sump Pumps in Haryana. We are quite particular about quality; that is why, we maintain strict quality guidelines and a team of quality controllers to ascertain each product’s efficiency and reliability.

Vertical wet pit volute pump with Dry motor Stage: Single Closed impeller Oil lubricated bearing arrangement antifriction bearing Mechanical seal gland packing

• Voltage: 415 V
• Number Of Stages: Single-stage Pump
• Motor Horsepower: Max 50 HP
• Brand: Harison Pumps
• Motor Phase: Three Phase
• Head: 4 to 48 m
• Motor Speed: 900 / 1450 / 2800 RPM
• Discharge Lpm: 50 to 3500 Lpm
• Sump Depth: Max 6 m
• Series: VEP

TECHNICAL DETAILS:•  Capacity upto 750 m3/hr.•  Total Head upto 90 mtrs. •  Operating Pressure upto 26 Bars•  Max. Stem Length 6.0 mtrs.•  Maximum Temp. 100° C APPLICATIONS   Condensate recovery. Circulation of industrial water. Acids & acidic water in metal & sewage treatment plants. Light hydrocarbons.      M.O.C.   Available in CI, Bronze, WCB, CF8, CF8M, A-20, R55, H-B, H-C. or any other special alloy   FEATURES     Centrifugal single stage pump with downward axial suction and radial discharge directly flanged to the discharge pipe.    The shaft is supported from its upper end by a grease lubricated ball bearing. Lateral supporting of the shaft is obtained through radial bush bearing, made from various anti-friction material, chosen according to the specifications of the fluids handled.  Vapour proof construction.   Radial bearings are lubricated either by the pumped liquid or through clear liquid from an external source. Lifting from intank / outside constructions along rivers, lakes, water sheds.

Vertical pumps are great alternatives to horizontal pumps. The pump is suitable for all clear liquids such as liquids, acids, alkalis, hydrocarbons, slurries, waste water, sugar melts and detergents.

• Pressure: Up to 3.5 kg/cm2
• Capacity: Up to 300 m3/hr
• Head: Up to 35 mtr
• Discharge Size: Dn 25 to 125 mm
• Temperature: Up to 50oC
• Speed: Up to 2900 rpm
• Pump Length: Up to 3 mtr

Applications : Sulphuric Acid, Nitric Acid, HCL Transfer. Solvents, Diesel & Petrol Transfer. Light Slurries, Organic Chemical Processing. Water, Cooling Water, Effluent, Cleaning Product & Hydrocarbons. Zink & Copper Plant. Salt, Pharmaceutical, General Industrial Services etc.   Features : Designed to meet specific lengths & application requirements. Base plate designed to meet exiting support arrangements. Standardized & modular design. Standard shaft sealing by oil seal, mechanical seal or stuffing box packing. Connects the pump casing with the base plate. Column pipe protects the shaft. Supports the eventual intermediate bush bearings. Suction strainers, simple mounting & self priming. Optimized hydraulic performance. Compact design using less floor space. Close / Semi open impeller. Easy maintenance, replaceable parts. Heavy duty shaft, sleeve & bearings.   Materials : SS-316, SS-316 L, SS-304, SS-304L Duplex Stainless Steel Super Duplex Stainless Steel Cast Bronze, Cast Steel, Cast Iron Hastalloy - B & C, Alloy-20 etc.

Heavy duty engineered polypropylene sump-pump for primery effluents / corrosive liquids and scrubbing systems. Zero maintenance pumps, eliminates the need for gland packing and seal Leak proof and can run dry without damage of rotating parts Pumps to be mounted out side the suction tank in vertical position and not to be submerged Vertical gland less pump, similar in hydraulic design to any conventional centrifugal pump, it differs in, so far as restriction is provided, escape by way of an overflow connection in the upper pump body & return to the suction line Preferred selection for E.T.P. Plant because of seal less design Pump is seal less hence can run dry Minimum component makes maintenance easy Low maintenance cost and prolong life Ideally recommended for transfer of treated effluent No mechanical seal / glands, hence pump can run dry Low maintenance cost and easy to maintain M.O.C. PP - UPTO 550- 600 C PPH - UPTO 90 01000 C PVDF - UPTO 100 0 - 1100 C We are fully committed to providing the finest pumps, the best engineering, the most effective customer service & the greatest after sales support possible.

• Voltage: 415 V
• Power: 15 KW Max.
• Country of Origin: Made in India
• Model Name/Number: FVFLP
• Brand: Flow Line
• Head: 50 Mtr Max.
• Max Flow Rate: 70 M3/Hour Max.
• Motor Horsepower: As per Customer Parameter
• No Of Phase: Three Phase
• IP Rating: IP44
• Usage/Application: Industrial
• No Of Poles: 4