Water Pre Heater Dealers

• Volume Range: 1000 – 10,00,000 m3/hr
• Temperature Range: 45-1200 Deg Celcius
• Outlet Emission: 10mg/Nm3 to 15 mg/Nm3
• MOC: M.S/S.S
• Efficiency: 99%

We Design and manufacture wide range of Water Pre Heating units for steam boilers or hot water recovery  from 1 ton/hr to 100 ton/hr capacity

• SIZE: 1-100 TPH

Water pre-heater a water pre-heater absorbs the flue gas heat into water thus, utilizing the heat from the exhaust gas which would otherwise be wasted. Plant efficiency is therefore further increased when viewed with respect to actual energy content of the fuel.

Several industrial processes require hot water. Some also require water heated to steam. Our industrial water heaters are well- known in industrial circles for the high quality of the raw material which we use and for their efficiency, reliability, long, trouble-free service and cost effectiveness. These heaters have also been installed in several large hotels, restaurants and resorts. Additionally, they are used healthcare, educational, multi-family dwelling and similar establishments. Large laundries and the food processing industry are among our customers.

We offer optimum quality Water Pre Heater For Boiler to our valuable customers. Processed as per the industry laid standards, these plants are commonly used to pre-heat water that has been delivered to a steam generating boilers. These water pre heating plants are known for their impeccable design and high water heating capacity.   Features: Very long service life No Corrosion Efficient Workout Specifications: Peak Heat Output: 1233 W Aperture Area: 1.68 m²

Typically, the flue gases leaving a modern 3-pass shell boiler are at temperatures of 200 to 300 °C. Thus, there is a potential to recover heat from these gases. The flue gas exit temperature from a boiler is usually maintained at a minimum of 175 °C, so that the sulphur oxides in the flue gas do not condense and cause corrosion in heat transfer surfaces. When a clean fuel such as natural gas, LPG or gas oil is used, the economy of heat recovery must be worked out, as the flue gas temperature may be well below 200°C.   The potential for energy saving depends on the type of boiler installed and the fuel used. For a typically older model shell boiler, with a flue gas exit temperature of 260°C, an economizer could be used to reduce it to 200°C, increasing the feed water temperature by 15°C. Increase in overall thermal efficiency would be in the order of 3%. For a modern 3-pass shell boiler firing natural gas with a flue gas exit temperature of 140°C a condensing economizer would reduce the exit temperature to 65°C increasing thermal efficiency by 5%.   Depending on fuel used for firing, THERMIN ENERGY provides bare tube, finned tube, gilled tube Economisers /Water Preheaters.

Recovers maximum heat from boiler flue gas Faster steam generation Saving of fuel up to 10-15% Easy to maintain Also saves flue

Energy plus supplies and installs air preheater (aph) and water preheater (wph) as per industry requirements. The purpose of wph is to recover the heat from the boiler flue gas, which increases the thermal efficiency of the boiler by reducing the useful heat loss in the flue gas. It also allows, control over the temperature of gases leaving the stack (to meet emissions regulations).

n present scenario of rising fuel prices Shanti Boilers offers wide range of efficient energy conservation products like Air Pre Heaters , Water Pre Heaters , Condensate Recovery Pumps , Pressure Regulating Stations  , Thermo Static Steam Trap Air / Water Pre Heaters :  Shanti Boiler’s Air Pre Heater / Waer pre Heater are design to utilize the high temperature flue gases and recover it, by either pre- heating combustion air going to the furnace or to heat the water at the ambient temperature to 75-80 deg c . The objective is to harness fully the available heat from flue gases and increase the over all efficiency of Boiler by optimally designing the Heat Recovery Units there by it results in fuel saving for the industry.  Model : SB-APH & SB-WPH Series Type: Vertical / Horizontal design

• CODE: Eh70
• Weight: +/-120kg (empty)
• Dia: +/-350mm

The EH70 electrical Pre Heater is an upgrade option for the EH144 and provides a robust and reliable 70kW sea water heating system that expands the heating capacity of the EH144 to 210kW of heating. The EH70 cannot be used as a standalone heating system as the safety requirement for electrical heating is controlled by the EH144. The EH144 can be supplied with certification from ABS or DNV.

A water pre-heater absorbs the flue gas heat into water thus, utilizing the heat from the exhaust gas which would otherwise be wasted. Plant efficiency is therefore further increased when viewed with respect to actual energy content of the fuel.

water pre heater, BENDS, Fittings, Flanges, Moisture Separator, Needle

pre heated solar water heaters, Solar Water Heaters

pre heated solar water heaters, Solar Water Heaters

Water Preheater, MS Water Storage Tank, boiler installation service

water pre heater, Coal Crusher, Electrostatic Precipitator, Chimneys

water pre heater, dump hoppers, Industrial Spray Tanks, Multitech Polariscope

Water Preheater, Mechanical Flow Meter, Boiler Air Nozzle, blow down valve