Wire Tester Dealers

• Power: AC or rechargeable battery. Multi-step low battery indicator is displayed,
• Capacity x Resolution: 200 x 0.1 lbF, 3200 x 2 ozF, 100 x 0.05 kgF, 1000 x 0.5 N, 1 x 0.0005 kN
• Accuracy: ±0.2% of full scale
• Wire gauge range*: AWG30 - AWG3*
• Wire diameter range: 0.01 - 0.25 in [0.3 - 6.3 mm]
• Minimum sample length: 6.5 in [165 mm], excluding termination
• Maximum sample elongation: 1.15 in [29.2 mm]
• Battery Life: Backlight on
• Backlight off: up to 24 hours of continuous use
• Sampling rate: 7,000 Hz
• Outputs: USB / RS-232
• Mitutoyo (Digimatic): Serial BCD suitable for all Mitutoyo SPC-compatible Devices.
• Analog: ±1 VDC, ±0.25% of full scale at capacity.
• Set points: Three open drain lines.
• Safe overload: 150% of full scale (display shows "OVER" at 110% and above)
• Weight: 16.1 lb [7.3 kg]

• Country of Origin: India

Cut through Test Set for Enamelled Winding Wire

• Brand Name: LRM NDE
• Frequency: 50 Hz
• Power Source: Electric 
• Voltage: 220 - 240 V
• Phase: Single Phase

As per IS:11000

• Features: LCD alphanumeric display, Keys with tactile feedback, Pass counters for each program, Easy diagnosis using self tests, Auto / Manual mode of testing along with, Relay on fail in auto mode of testing
• Usage/Application: Industrial
• Location: India
• Payment Mode: Cash, online, cheque
• I deal in: New Only

• Name: USB Cable Tester
• Basic Accuracy: ±5%
• Measurement Speed: 0.1Sec Basic
• Test Signal Level: 5Vdc ±5%
• Insulation: Resolution (8681 only)
• Resistance: Resolution (8681 only)
• Hipot: 100 – 1000Vac ±1%, 50V Resolution
• Display & Sound: 320×240 Graphic LCD Display
• Pass/Fall LED Indicator Internal Speaker: Internal Speaker
• Connections: 128 Test Points
• 256 Points: Hipot Calibration +/- Output
• Auto Pin-Search Jack: Front Panel Control Buttons

• Specimen size: 180 x 150 Sq.mm max. & 15 x 15 Sq. mm min.,
• Thickness: 10mm to 80 mm.

CrAl based fine wire based thermocouple for temperature sensing, Temperature Range: Adjustable up to 960° centigrade, Self adjusting constant current mode operation as soon as heater-specimen contact is established, Time Controller: Micro-controller based programmable timer 0 to 999secPrecision scale: Precision scale is provided to measure the height of the flame

We are a reputed Manufacturer and Supplier of Megger Wire Tester, based in Delhi. Our Megger Wire Testers are highly appreciated for their accuracy and longer working life. These Megger Testers are available in various models to meet the requirements of the clients. Advantages : Highly accurateEasy to operateDurableSuperior performance Product Details : Output : 110V/1000M-ohm

• 2 Wire Loop impedance testers: 2 Wire Non-tripping loop tester , 50 V to 440 V operation

The new Megger two wire earth loop testers verify the loop impedance of a live electrical circuit, ie without the need to disconnect the electrical supply. The new LTW300 series instruments offer a 2 wire loop testing solution that does not trip 30 mA RCDs and can be used on a wide range of voltages.

Hot wire ignition tester is according to the standard requirement of IEC60695-2-20 and GB4943, which meets Standard Test Method for Ignition of Materials by Hot Wire Sources. It is suitable for electric and electronic products, household appliance materials to do ignition dangerous test. It simulates the heat source or ignition source of simulates glow component and overload resistance which may cause thermal stress in a short time. Hot-wire coil ignition test adopts the specific size (Dia: 0.5mm; Length: 250mm) and specific material (Ni80/Cr20) of heater strip which is pre-annealed with required heating power (0.26W/mm) and specified time (8s~12s). Then coil heater strip on the specimen for 5 cycles according to certain wire wrapping tension (5.4N) and certain wire wrapping distance (6.35mm). Then take the specimen with wrapping heater strip to test until 120s under the stipulate heating power (0.26W/mm) the users can judge the fire risk according to whether the specimen ignite and the ignite time.

• Feature: Expandable hardware channels per requirement, User friendly software suite, Learns from sample board

The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.

electric wire tester, Electrical Panel, Electrical Switches

Wire testers, electric counter, Digital Energy Meter

wire harness testers, Clutch Mechanism Crimping Machine

wire ropes testers, hydraulic bolt tensioning tools, Hydraulic Products

wire harness tester, eyepiece less inspection system

electric wire tester

4HT Master Slave DSU Wire Harness Tester

Continuity Wire Tester, MCB Shorting Strip, aluminum terminals

Cable Wiring Harness Tester, Crimp Cam 1900 Visual Inspection Equipment

Wire Pull Tester, Automatic Wire Cutting, Stripping And Twisting Machine