Heat Pipes Dealers

Are you looking for the best solar water pipe system? If yes, then there could not be a better place than this. We are an established name known for manufacturing the best solar products and Solar heat pipe system is one of them. Here, we will discuss the solar heat pipe systems and their workings. You can feel free to contact us anytime to buy the cost -effective solar heat pipe systems. This type of Solar Water Heater can work at high pressure. It uses the heat pipe to deliver the heat energy. Because of the no water in a vacuum tube, there is no tube breakage in winter, even in the coldest area. Each vacuum tube can work alone, so it can still operate in the event of tube breakage.

FEATURES: 1. Study of the connected of double & single lagging 2. Study of effects of different insulating material combinations3. Electrical input control & measurement with complete penalized instruments.4. Digital Temperature indicator. INTRODUCITON:Lagging of pipes is required to prevent leakages of heat. The Apparatus is designed to study the lagging phenomenon. In Lagged Pipe Apparatus three concentric pipes are arranged between the pipes are filled compactly by two different insulating materials and heater is provided at the center of inner pipe. Temperature at various points is measured with Temperature indicator. Heat input is measured by Voltmeter - Ammeter. The assembly is mounted o angle frame. SPECIFICATION: 1)  Pipesi)    M.S. Pipe inside - 5cm dia. Approx   ii)   M.S. Pipe Middle - 10 cm dia approx.iii)  M.S. Pipe Outer - 15cm 2) Length of Pipes -1m approx.Control Panel consisting of a)  Voltmeter - 0 - 100/200 volts.b)  Ammeter - 0 - 2 Amp.c)  Diammerstat for heater, 0-230 V, 2 Amps.d)  Digital Temperature indicator, 0-300 0 C with 10 C least count, using chromel-almel  thermocouples, provided with cold junction compensation.4)   Nichrome cartridge heater of suitable capacity  and length EXPERIMENTATION: 1)   To determine heat flow rate through lagged pipe and compare it with the heater input for known values of thermal conductivity of lagging material.2)   To determine thermal conductivity of lagging material by assuming input to be heat flow rate 3) To plot temperature distribution across lagging material. SERVICE REQUIRED : 1)  To determine heat flow rate through lagged pipe and compare it with the heater input for known values of thermal conductivity of lagging material.2)  To determine thermal conductivity of lagging material by assuming input to be heat flow rate 3) To plot temperature distribution across lagging material. Almost  care is taken for preparing this literature, but still if there are any mistakes,  those may be excused.  We reserve our right to change or modify the equipment without notice.

We can offer a comprehensive range of Forged Fitting for the right technical solution. Hallmark Metallica manufacture & export wide selections of Forged Fitting AISI 4130 Forged Fittings AISI 4130 Buttweld Fittings at most attractive price as per customer requirements, we can also manufacture Forged Fitting in ASTM/ASME/ANSI grades as per our customer budget, we enjoy the reputation supplying Forged Fitting at cheapest in steel industries around the globe.

IT consist of three concentric pipes, at the axis of which a cartridge heater is positioned

Customized design for various customers for centrifugal compressor Intercoolers & after coolers. Capable of cooling large volumes of air or nitrogen at minimal pressure loss. Close temperature approach to cooling water is possible. Removable bundle design with multi-pass tube side. Internal demister mounting for Wet Air condensation. Most compact and energy efficient solution for your gas cooling application.

Keeping in mind their so many uses, we come up with different variants of Heat Transfer Pipes such as ASTM A 214/A 214 M – 96 Pipe, ASTM A 556 / A 556M-96 Pipe, BSI BS 3059-1:1987 Pipes. ISO 2604-II: 1975 Pipes, ISO 2604-III: 1975 Pipes, BSI BS 3606:1992 Pipes and many more. We are reckoned among the reputed Exporters and Suppliers of Heat Transfer Pipes from Maharashtra, India. Delivering retail as well as bulk orders for Heat Transfer Pipes on time has never been an issue for us due to our vast distribution network.

we are offering heat exchanger pipes. we source heat exchanger pipes keeping in mind the desired properties that make them apt to be used in heat exchangers, boilers and similar equipment. the heat exchanger pipes are well-tested to ensure the best quality by the manufacturers who supply them to us. the heat exchanger pipes can be availed from us in various specifications at affordable rates. why our heat exchanger pipes? resistant to temperature and pressure extremities excellent finishhigh enduranceexcellent tolerance

• Features: Resistance to corrosion, Requires low maintenance,High Strength

• Type: Seamless / ERW / Welded / Fabricated / LSAW Pipes
• Grade: SMO 254
• Standard: ASTM A312, A269, A213, A249, A358, UNS S31254
• Size: 1/8”NB TO 12”NB
• Form: Round Pipes/Tubes, Square Pipes/Tubes, Rectangular Pipe/Tubes, Coiled Tubes, “U” Shape, Pan Cake Coils, Hydraulic Tubes
• Length: Single Random, Double Random & Required Length
• End: Plain End, Beveled End, Treaded

hell and tube heat exchangers consist of a series of tubes. One set of these tubes contains the fluid that must be either heated.

We are offering best Heat Exchange Pipe.

• Usage: ladder, automobile products

We are offering sintered wick structured heat pipes. In this type of heat pipe, capillary wick is made of sintered powder which adheres to the inner walls of the heat pipe. This acts to transport the fluid through capillary action.

• Material: Mild Steel
• Shape: ROUND
• Brand Name: STERLING
• Type: Integrally Finned Tubes
• Size/Dimension: 6MM TO 50MM
• Part Type: Exchanger Tube
• Usage/Application: HEAT EXCHANGER
• Size Diameter: 6MM TO 50MM
• Exchanger Type: Shell & Tube

Trader & Supplier of Heat Exchange Pipe. Our product range also comprises of Capillary Tubes And Pipe, Instrumentation Tubing Pipe and Tubular Heater Pipe. With our vast experience & knowledge in the respective field, we are engaged in trading and supplying a wide range of Heat Exchange Pipe.  

• Specification: Grade
• ASTM A 179, A 199, A 200, A 209, A 210, A 213, BS 3059: T-1, T-5, T-11, T-22, 33, 45, 620 & 622

• Color: Green
• Thickness: 4.2 mm
• Single Piece Length: 18 meter, 6 meter