Universal Tester Dealers

• Feature: Available in Table top model to Heavy vertical model,Sturdy and heavy structure for stability during tests,Powder coated and hard chrome parts.

Tensile Testing is one of the most common mechanical testing techniques. It is used to find out how strong a material is and also how much it can be stretched before it breaks. This test method is used to determine yield strength, ultimate tensile strength, ductility, strain hardening characteristics, Young’s modulus and Poisson’s ratio.

• Application: Indsustrial Usage, LCR Monitor
• Power Source: Battery, Electric
• Voltage: 230V AC 50 Hz+-10%
• Display: 40*2 Backlit Alphanumeric LCD
• Keyboard: 24 Keys Membrane Keyboard.
• Test Range: Digital & Linear ICs 6, 8,14,16,20 pin in DIP pack. Active & Passive Components
• Enclosure: Sheet Metal Cabinet with Powder Coating and Engraving.

MME - UT 20 is the latest Microcontroller based Universal IC tester with LCR Meter from Minmax Electronics. It functionally tests 74 series of TTL ICs 40 & 45 series of CMOS ICs, Analog/Linear ICs op amps, comparators, timers, transistor arrays, ADC, DAC etc., It also tests components like diode, transistors, UJT, FET, SCR, Displays, Regulators (78/79) and DIP relays. It also measures the values of Inductance (L), Capacitance(C) and Resistance(R). MME-UT 20 has Rs232 Serial Interface through which IC test Library could be expanded.

We are offering universal hardness tester - analog display (digital display also available) -testing force : rockwell 150 kg, brinell 187.5 kg, vickers 100 kg. -loading control : automatic

Elind Battery Universal Tester as the name suggests, is a versatile multi testing station designed to test all types of lead acid as well as Ni-cd Batteries as per various National and International specifications. The unit can be used for conducting any of the following tests. Capacity test Charge / Discharge Cyclic Test Endurance Test / Resistance to over charge test Ampere Hour / Watt Hour efficiency test Charge Acceptance test Water loss test Retention of charge test The unit comprises of electronically controlled constant current / constant voltage Battery charger and constant current discharger, along with Micro controller based programmer with LCD display to set Charge / Discharge / Pause program sequence, Charge / Discharge current and Step termination parameters like time, voltage, Ampere hours and number of cycles etc. Built in data logger sends test data to a printer or to a personal computer at set time interval. Test data can be printed on a 80 column serial printer or recorded / displayed on personal computer through user end PC software. Stored data can be used to draw graphs of voltage / Current / AH / Temperature / Time as per requirement.   SPECIFICATIONS:   INPUT : 1 Phase AC 200-240 volts / 3 Phase 380-440 volts, 50Hz. CONTROL : Charging-Constant Current / Constant voltage + 1%Discharging – constant current + 1% CH / DCH Time : 1 Second to 100 Hours (99 Hrs 59 Min 59 Sec). NO. OF STEPS / CYCLE : 8 Steps of Charge, Discharge Or Pause. STEP TERMINATING PARAMETER : Time / Voltage / Ampere Hours. CYCLES : 1-9999 Cycles. INDICATIONS : Digital Voltmeter & Ammeter Charge / Discharge / Pause and Cycle complete. PRINT INTERVAL : 1sec to Hours. DATA ACQUISITION : Battery / Cell voltage,Charge / Discharge Current, Amp-Hours,Water bath / electrolyte Temperature,Real time, Date, Mode, (Ch / Dch / Pause). PROTECTION : Against overload, Short ckt., Rev. polarity.

We are offering universal ic tester. Features1. Tests a wide range of digital ic's such as 74 series,40/45 series of cmos ic’s.2. It can test microprocessor 3. It tests peripherals like 4. It tests a wide range of analog ic’s such as adc, dac,opamp, 555, transistor arrays, analog switches,waveform generator, line drivers, voltagesregulators, pll’s, vco, pwm generator, sample &hold, voltages references, opto couplers,comparators, voltages followers and others.5. It tests seven segment display of common cathode &common anode type6. It has auto search facility for digital ic’s.7. Test by: truth table / sequence table comparison. Analog ic’s.8. Keys: 50 cherry keys key pad with numerical & functional keys.9. Display: 16x2 backlit lcd display.

• Weight: 0.06Kg(s)

• Type: Universal
• Voltage: 220V
• Frequency: 50Hz
• Power: 1-3kv
• Warranty: 1 Year
• Feature: Durable, Easy To Use, Superior Finish
• Automation Grade: Automatic

• Precision: 0.01 mm
• Display Size: 1.8
• Battery Life: 3000 hrs
• Display Mode: May be switched to inch or metric
• Item: Good working condition

Included in delivery -Metric version Universal 3D-Sensor with clamping shank 20 mm, short probe tip 4 mm -Inch version Universal 3D-Sensor with clamping shank 3/4', short probe tip 0.2'   Technical data subject to change without prior notice. Probe tips The sensors can be equipped with a short (ball 4 mm / 0.2") and a long (ball 8 mm / 0.4") probe tip. The probe tips may be changed without any tool, no re-calibration of the unit is needed. The probe tips of course are compatible to all HAIMER 3D-Sensors.

Compression pressure,cooling system pressure,oil pressure,common rail pressure,fuel pressure (mechanical & electrical) Robust ABS housing ,illuminated LCD display and membrane keypad,measuring range 0....60 bar870 psi,12 V supply voltage,with memory and RS 232 interface.

A Universal Testing Machine otherwise known as a materials testing machine or test frame is used to test the tensile and compressive properties of materials. Such machines generally have two columns but single column types are also available. Load cells and extensometers measure the key parameters of force and deformation as the sample is tested. These machines are widely used and would be found in any materials testing laboratory.A typical testing system is comprised of a materials testing machine or test frame, control and analysis software, and critically, the test fixtures, accessories, parts and devices used to hold and support the test specimen.A comprehensive range of tests can be carried out such as Tensile, Compression, Crush, Friction, and Flexural on materials like Plastics, Metals, Paper, Fabric, Yarn etc.The AT Series stand-alone bench mounted or floor standing single or twin column universal strength testing machines with integral PC system & windows software utilises the latest touch screen technology. The machine comes complete with the feature-rich winTest software for machine control and testing with comprehensive on-board test methods that are compliant with all relevant industry standards including advanced, standard and complex multistage test procedures. Printed reports can be easily generated and test data can be transferred directly to other software applications for enhanced report generation, SPC trend analysis, laboratory manager reports etc.   Standard Features includeHigh specification Computer controlled Universal testing machine, 15" Touch Screen Display with interactive machine control console, Integrated industrial computer module comprising 1 GHz CPU with 256MB Ram, 40 GB Hard Drive with Windows XP operating, LAN, USB & RS232 ports, Max tension and compression resolution 0.1N, 800% overload capability on load cells, Accuracy of better than 0.5% of indicated reading down to 1/1000th of load cell, Meets and exceeds BS EN ISO 7500-1 1999 Tension Grade 0.5, Compression Grade 0.5 and meets all other International standards, Force sampling rate 1000/s Rigid Dual Column Frame with Crosshead guidance system PC control of crosshead position, resolution 0.001mm, Twin recirculating ballscrews eliminating off centre loading, High accuracy closed loop speed control Test speed 0.001 to 1000 mm/min, RS232 output for PC, Fixed load and travel protection limits, User selectable load and travel limits, PC Controlled load and extension cycle testing, plus long term creep testing, Digital control specimen break detection, Automatic check and adjustment of machine calibration, Impact and overload protection, Auto zero, Direct connection to extensometers, Aluminium extruded columns with integral T slots for mounting of accessories such as extensometers, guards, lighting etc, Supply voltage 200/240V AC or 100/120V AC at 50 or 60 Hz.Optional Accesories available400 different grips available, Wedge, Tensile, Pneumatic, spring action etc, 3 and 4 point bending fixtures, Compression Platens, Extensometers, Test Chambers.

The UNIVERSAL TENSILE TESTER is used for determining the ability of the material to withstand forces that tend to pull it apart & to determine to what extent the material stretches before breaking.Different type of plastic materials are often compared on the basis of TENSILE, FLEXURAL STRENGTH, ELONGATION, & TENSILE MODULUS DATA. Many plastics are very sensitive to the rate of straining and environmental conditions. The tensile property data are more useful in preferential selection of a particular type of plastic from a large group of plastic materials.Tests for tensile strength (stress at fracture of the specimen) and elongation (extension of material under load of plastics. The first provides a measure of the breaking strength of the material but is radically affected by the rate of loading and the ambient temperatuere. Tensile strength in kgf/cm sq. = load (kgf) / a x b (cm sq.) Elongation % = (L2-L1) x 100/L1. Standard test methods : BS 2782 method 301, ASTM D 638, ISO R527.

Many industrial sectors are driving innovations in new materials from biomaterials, bone, fibers, threads, thin films, wire and more. However, that innovation requires measuring the mechanical properties of miniature samples.

“vaiseshika”universal hardness tester, type: 7005 uht-d is a wonderful hardness testing machine which can take care of hardness measurements in the units of brinell, rockwell & vickers. Therefore, the universal hardness tester is three-in-one equipment which takes care of industrially applicable all ranges of rockwell namely hra, hrb and hrc and brinell scales and vickers scales of hv30 and hv100. For more details please study the detailed specifications.

• TESTING BATTERY: 2V TO 30V
• MODE OF DISCHARGING: Constant current/ CR.
• Mode of Charge: Constant voltage/ CC.
• CHARGE/ DISCHARGE TIME: 1 MIN-99 Hrs 59 MIN.
• Test Stop: Set time/ set volt/set Ah Set No of cycles.
• VOLTMETER/AMMETER: 3 1/2 / 4 1/2 digit 7 seg LED LCD module.
• BUILT IN DATA LOGGER: Individual cell monitoring 9 channels.
• DATA OUTPUT: Serial/USB to pc/printer.
• POWER SUPPLY: 230V A/C.
• STANDBY: 12V Battery.

Well-designed cheap professional programmer, Production of high-density SMD technology, a unified user interface, easy to use, fully functional, reliable program running of application software, ultra-small code, runs faster, supports bilingual(English and Chinese), it can automatically identify the operating system to install and run under WIN 2000/WIN XP/WIN 2003/WIN 2008/WIN VISTA/WIN7/WIN8. Features:– The great part of other development programmers are not comparable to its functions, that is not easy to reach. – High Speed Programming: This programmer has Built-in MCU with high-performance and high-capacity USB interface , at the communication speed of 12Mbps, being in line with ( For each chip) well-designed programming algorithm and USB high-speed communications. It may be one of the fastest integrated development programmers, the speed has been met the needs of small-quantity efficient production.Compared to similar products, some chips’ programming speed is several times faster, even more than 10 times. For 4Mbits parallel FLASH ROM, the upgrade programmer (Version 3.01 or above) takes only about 35 seconds to finish programming (the total time of erase, write, verify). It only takes about 32 +79 seconds to read and write a 32MB TE28F320. In most cases, the parallel flash chip can be programmed at the same time it can be verified. The programming will be immediately stopped if there is an error. It only takes about 12 sec (read) +18 sec (write) to read and write an 8 Mbits of serial 25P80. It only takes about 98 sec +160 sec to read and write a chip of 64MB capacity. It supports common 8-PIN and 16-PIN 25 series chip with large capacity.Note: 16MB or larger capacity flash chip cannot be programmed by general programmers because of programming speed, while the TL866 programmer can widely support 64MB Serial and parallel series of chips to 48PIN. It provides with the remarkable quality that is distinct from other common programmer. – support a wide range of chips: All kinds of 26, 27, 28, 29, 37, 39, 49, 50 parallel ROM, EPROM, EEPROM, 24, 25, 35, 85, 93, 95 Series EEPROM, Serial parallel ROM chips, fully supporting to the 48-PIN chips of 64Mbits capacity. It also supports a variety of models of 51 series of microcontroller, AVR microcontroller, including ATMEGA series, ATtiny Series, AT90XXX Series MCU, MICROCHIP PIC10 PIC12 PIC16 PIC18 MCU, programming of GAL programmable logic device, SRAM test, 54/74 and CMOS4000 series IC comprehensive function tests. At present, it can actually program more than 12000 chips. More chips will be supported in the process of the future upgrade.—View: Click here to view the chip supporting list – Unique ultra-low power: The whole programmer is equipped with the ultra-low power chips and it is furnished with electricity via USB Interface. It is the first comprehensive programmer to program all the chips without an external power supply. Their own power consumption is less than 20mA (it is 7mA when the programmer is not programming, LED power indicator use largest electricity, 5mA each one) and Programming power loss rate is less than 20% so that the programmer can supply the high VCC VPP programming electric current. Programmable chip can be provided with enough programming power (the largest programming power output is 2 watts that is impossible for a chip to use 2 watts of programming power). And you hardly feel the heat of the programmer after such long continuous work. – easily portable performance: This is one of the smallest products in the world and the dimensions are 10CM*6CM*2.5CM (it is as small as a driving license). In addition, you don’t need to carry with an external power supply because of its ultra-low power that makes it more portable. – Programmable programming power supply: VPP and VCC programming voltages are independently program-controlled: programmable VCC is from 3.3V to 6.5V; VPP is from 3.3V to 21V. The fluctuation of power supply is minor because of the multi-stage LC filter. – Best overvoltage, overcurrent protection: VCC, VPP power supply of the Programmer is furnished with the independent Grade 3 overcurrent protection and the protection of automatically cutting off power supply. Each pin of 40-pin programming socket has VPP overvoltage protection. It can effectively prevent from putting a chip in the wrong place or short circuit due to other reason. In this programming case, it can also stop VPP high voltage from coming back to the internal of the programmer and damaging the device. Really make sure that the programmer will not be damaged when there is any worst-case short circuit. At the same time, the programmed chip can be efficiently protected.This programmer will cut off the programming power supply VPP and VCC within 100us and send the message to the application program when there is short circuit. The programmer and PC won’t be reset when there is short circuit because of the multilevel overcurrent protection. – 40PIN universal pin: It is the most versatile pin among 40PIN quasi-universal pins. You don’t need to move or turn around the chip when programming, just congruously put the chip forward and the handle direction of the programmer is the PIN1 place. Its design accords with the common operating habit of user. – This programmer is equipped with upgrading Function of the built-in hardware firmware program that can make sure your programmer’s firmware flash and application software can be timely updated. You can complete the upgrade by downloading the upgrading program through the manufacturer’s website. – Second development function of chip serial number: This programmer has a variety of automatic numbering functions that are used commonly. You can get any serial number through DLL Dynamic Link Libraries by using the custom algorithm. In mass production, the function enables each chip to produce only one identifying information that can be encrypted by the custom algorithm. So you can effectively protect your rights as a customer. – Unique universal serial programming interface ICSP: (Only TL866A can support, TL866CS cannot use this function)This TL866A programmer can program through the 40-PIN universal socket and is provided with an ICSP serial programming port. For some in-circuit serial programmable chips, you can program MCU by choosing ICSP port. You can get the clear instruction diagram in the programming software for the ICSP port wiring method. That is to say, you can directly program and update the chip soldered on the board.Note: Now ICSP can in-circuit serial program ATMEL89S51, ATMEL89S52, AT45DBxxx, a whole series of AVR ATMEGAxxx, MICROCHIP PIC10Fxxx 12Fxxx 16Fxxx 18Fxxx, as well as a full serial of SYNCMOS SM59Dxx SM59Rxx. The variety of microcontroller that can be supported in-circuit programming will be continually increased in the future. Six ICSP wires of this programmer, except a ground wire, other wires led full functional I2C, SPI and UART serial main wire, be suitable for all kinds of serial communication. In addition, each wire can supply VCC, VPP or GND with high current. -superb 54/74F/LS/HC CMOS4000 series IC functional tests: This is the first development programmer to test the common logic integrated circuit and this test can be located the errors of logic gate circuit, as well as test any possible input combinations of integrated circuit. -Programmer self-testing function: This programmer can test itself on each pin of VPP, VCC, GND and I/O information, at the same time it can run an inside short-circuit test on VPP, VCC current. -AVR microcontroller one-to-one soft encryption: AVR microcontroller has an RC Calibration (calibrate bytes). Only one of dozens of chips may have the same bytes value and it cannot be modified. Microcontroller software can read this value and determine whether the code is used by other chips. Through custom encryption algorithm, it can stop those who decrypt chips with ulterior motives from directly using. The encryption algorithm is so complex that it is not easy to decrypt. But, about “encryption”, there is a problem for developers – each chip is different – it is impossible to manually calculate one by one and respectively compile source code if the algorithm is complex. This programmer can automatically read into RC bytes before programming. The developer can get the bytes value of the chip in the DLL dynamic function and then automatically calculate the encrypted data according to the request and put it in the memory, efficiently completing mass production. (A detailed encrypted instance of the ATMEGA8 in the installation package is available for reference) -Unified and convenient user interface: The user interface is well-designed and is in complete accord with the operating habit of the Windows series of software. Built-in binary editer is comparable to pure professional editing software. You can directly read, write and modify the files such as BIN format, HEX format, JED format and so on. In addition, it has the complete and practical project mode that makes the mass production more convenient and safer.

We manufacture and offer quality range of cement, concrete and aggregate testing machines. These machines are ideal for checking compressive strength of concrete blocks, bricks, rubber pads, and buffer springs.

Tensile test is a measurement of ability of material to withstand forces that tends to pull it apart and to determine to what extent the materials stretches before breaking.   The "Saumya" UTM gives highly accurate force measuring system with hi-tech design and is available in different models for testing a variety of materials. Load cells, grips, fixtures can be interchanged easily to perform different tests like Flexural, Compression, Co-efficient of Friction, Peeling and bonding strength.             STANDARDS :   ASTM D 638, D 882, D 790, D 695, ISO R527, BS 2782 and other equivalent standards.   APPLICATIONS:   Tensile is the universal test applied to many polymers to check the mechanical properties & it is the most important property as majority of end use application involved some degree of mechanical loading & properties like Tensile modulus, Elongation, Compression etc. are calculated using this machine. For woven sack tanacity will be directly displayed.     USP: The "Saumya" has some unique models developed with versatility in mind. "Saumya" UTM's can be used with or without using P.C. Universal software capable of performing test on any type of materials. Safety provisions in form of software, Electrical & Mechanical features. Test on high & low loads with different cross-head travel speed can be performed. The "Saumya" tensile offers testing flexibility and ease of use via an intelligent electromechanical system data transfer ratio of load cell to instrument is 24 bits to give instatenuoes readout of data during process. The "Saumya" versatile software helps to visualize the process and behavior of materials in form of data and graphs with all the calculated results required. Units of weights "Newton" or "Kilograms" can be selected from software. Round or of any different shape meterials can be pre specified on specification window for direct calculation of area.   The Equipment is known as Universal Tensile Tester, Computerised Universal Tensile Tester, Automatic Universal Tensile Tester, Plastic Universal Tensile Tester, Universal Testing Machine for Plastic Lab, Tensile Strength Tester, Plastic Tensile Test Measurement Machine, Twin Screw Tensile Tester, Tensile with Compression Tester, Plastic Film Tensile Tester, Plastic Maximum Tensile Strength Measurement, Universal Materials Testing Machines, Plastic Material Testing Machine, Universal Tester, etc.    

• Application: Ordinary Battery
• Weight: 60 g
• Voltage: 1.5V, 9V
• Dimension: 10.5 X 4 X 2.5 Cm

NAUGRALABS LABORATORY PRODUCT NAME: UNIVERSAL PENDULUM IMPACT TESTER FOR TESTING LAB NaugraLabs Laboratory Product Code: NLE-Export-111004 Description and Specification for Lab Tenders Universal Pendulum Impact Tester.  Release of pendulum by Hand operation Safety guards for protection Braking arrangement provided to arrest the swing of pendulum after specimen rupture. Capacity 30kgM / 300 Joules   Charpy and Impact Tension Test Izod Test Pendulum drop angle 140° 85° Pendulum effective weight 20.59 kgs. 21.79 kgs Pendulum speed 5.3465 m/sec 3.857 m/sec Pendulum Impact Energy 30 kgM (300 J) 16.4 kgM (164 J) Min. graduation 0.2 kgM (2J) 0.2 kgM (2J) Distance of axis of hammer rotation and centre of test piece/point of test piece hit by hammer 825 mm 825mm Max. permissible loss by friction X windage, etc 0.5% of max. impact energy mechanical lab equipments manufacturers  Steel & Metal Mechanics Lab equipment manufacturers,exporters and Steel & Metal Mechanics Lab suppliers