Wrenches Dealers in Pali Road, Faridabad

• Material: Steel
• Length: 2mtr
• Application: Automotive Use
• Color: Black
• Feature: Corrosion Resistance, Durable
•  Finishing: Coated

We are a trusted Manufacturer, Exporter, and Supplied of Poker Vibrator Shaft that is highly acclaimed by the clients due to its sturdy construction. Our Poker Vibrator Shaft is fabricated from quality raw materials to assure a longer functional life. Due to its dimension accuracy, our Poker Vibrator Shaft is highly demanded in the market. Characteristics Design in conformity with International standards. Excellent results on light duty jobs Economical solution when it comes to internal vibration Can be Driven By Petrol engineDiesel engineElectric motor Principle Single piece rotating pendulum generating vibration at 12000 rpm Dimensions Ranging from 25 mm diameter to 80 mm diameter Caution Do not use the poker vibrator to move the concrete sideways Different Hose Lengths : The hose has been treated to increase its strength and make it more resistant to wear and tearHigh frequency pokers with over dimensioned internal motorHose with special anti-abrasion protection Important : Do not leave the needle running in the air as it will overheat and is only efficiently cooled when immersed.Do not stop the vibrator whilst needle is immersed as withdrawal will be difficultDo not lubricate the inside of the needleClean the needle end tip after every 50 hours of useStrike the needle against the ground to start vibrationsWhen handling needle, always carry it by grasping the rubber sleeve round the drive shaft thus preventing excessive bending of the shaft. Acute bends will cause friction and tend to overheat. Therefore, always keep the flexible shaft as straight as possible when running.To stop the engine, switch off the ignition and turn off the petro.Ensure that needle is immersed fully in the concrete.Needle and flexible shafts should be serviced and cleaned with petrol every 100 hours of use. The Avon Wire Braided Series is unique. Wire braided rubber hose is made of synthetic rubber and strengthened with wire braided fabrics. It usually consists of �Four or More Layers� including inner Rubber Layer, Middle Rubber Layer, One, Two or Three Steel Wire Braided Layers and outer rubber layers. Wire Braid Hydraulic Hose, Tube ; Oil resistant synthetic rubber reinforcement: Wire Braid of high-tensile steel wire. Cover: Black, Abrasion and Weather Resistant Synthetic Rubber. These kinds of hydraulic rubber hoses are mainly used in mines and. oil field exploration, suitable for construction, lifting transport, forging metallurgy, mining equipment, ships, injection molding machinery, agricultural machinery, machine tools, as well as various industrial sectors. Mechanization and automation of hydraulic transmission system in a certain pressure and temperature of the oil (such as mineral oil, soluble oil, hydraulic oil, fuel oil, lubricants) liquid, water-based liquid (such as emulsion, the oil-water emulsion, water), such as gas and liquid transmission are used). Characteristics of Rubber Hose : Resistant to oil and greaseResistant to frictionBandage finishWorking temperature:- 30°C to 110°C Mechanical Characteristics : Minimum bending radius-20 cmWhen the hose is bent to the minimum radius after recovering the straight shape.Steel braid 0.3 steel wireWorking pressure: 40 kgStrip material: steel spring PIAV Series The PIAV series has been developed and designed to meet international quality standards. We offer an economical alternative to the PIAV series, while giving excellent results on light-duty jobs, PIAV pokers have been designed to minimize operation and maintenance costs, therefore meeting the needs of contractors looking for an economical solution when it comes to internal vibration. The perfectly balanced pendulum results in high output. The PIAV pokers can be driven either by a petrol engine, by a diesel engine or by an electric motor. The PIAV series, ranging from 25 mm of diameter to 80 mm, feature high frequency and amplitude to ensure the best results in all types of concrete. Principle: a unique balanced single piece rotating pendulum generating vibration at 12000 rpm. The contractors can rely on a long work life thanks to high quality components and production processes. Technical Specifications ModelPIAV-2506PIAV-3806PIAV-4506PIAV-5706PIAV-7006PIAV-8006Head Diameter (mm)253845577080Head Length (mm)385330360370375375Head weight (kg) complete1/2602/0003/1805/1207/5408/000Frequency12000120001130011000108009000Amplitude1.21.62.02.42.83.6Weight vibrations (m/s2)2.364.023.502.482.662.88Rubber Hose (Dia (mm) x length)30x6 mtr30x6 mtr35x6 mtr35x6 mtr35x6 mtr42x6 mtr Important The above information is a general description only. It is not guaranteed and contains no warranties ot any kind Starting Move the locking lever on the coupling forwardInsert the poker vibrator coupling into the guiding sleeve of the drive unit.Rotate the motor coupling slightly until the clutch dogs engage with the guiding sleeve dogs.Release the locking lever. If the coupling dogs are in engagement the lever will return to its original position. Never connect the poker vibrator to a drive unit that is running : On starting it may sometimes be necessary to jolt the poker vibrator sideways to start it vibrating. Make sure that the operating hose does not describe any sharp bends or loops as this will increase wear and reduce its useful life. Performance Chart Total no of days poker works without repair180 days minimum/maximum 240 daysTotal cubic meters of concrete without repair Minimum 4000 cubic meters/max. 5000 cubic metersAverage breakdown it mishandled Very rareAverage breakdown when in proper use NilAverage repair if breakdown occurs after the above given figures25% on the basic cost of pokerTotal no of needle mechanics required to be kept at site during concreting If the site condition has round about 1000 cubic metes if concreting daily is only oneBasic cost of poker other than the branded needle It depends on the size Other Vibrator Pocker Performances Total no of days needle works without repair30 days the maximumTotal cubic meters of concrete without repair Maximum 300 cubic meterAverage breakdown if mishandledVery frequentlyAverage breakdown when in proper useFrequentAverage repair if breakdown occurs after the above given figures125 % of the basic costTotal no of needle mechanics required to be kept at site during concretingIf the site condition has round about 1000 cubic metes, if concerting daily, minimum four

• Model Number: Shaft For Gear

We offer shaft for gear.owing to our expertise in this domain, we are able to provide an optimum quality array of shaft for gear. The provided gear is manufactured using quality-tested raw material and latest techniques under the supervision of our adroit professionals. Offered gear is widely appreciated by our clients for various qualitative features like optimum finish and accurate dimensions. Our esteemed patrons can be availed these gears at market leading prices.

• Material: Alloy Steel,Alloy Steel
• Usage: Tractor,Tractor
• Features: Fine Finishing, High Efficiency, Hard Structure,Hard Structure, Fine Finishing, High Efficiency
• Colour: Metalic Silver,Metalic Silver

We are specialized in Steering Shafts, Steering Worm, Steering Gear Box Assembly, Steering Wheels, Tractor Gears, PTO Hub, PTO Drive Pinions, Counter Shaft, etc.for use in, Agriculture & other Aftermarket Application. Our Products are marketed across to world over USA,U.K., Europe, Latin America, Australia, Middle East, Far East, African & Asian Continent and our Customers base includes OEM’S large rebuilders in Organized Sector and Distribution Houses. Deals: Massey, Ford, Fordson, Fiat, Kubota, Deutz, Yanmar, New Holland, John Deere, Case IH, IMT, UTB, Ursus, Sawraj, Perkins, Escort, JCB, Mahindra, Steyr.

• Features: Durable, Corrosion Resistance, Easy Installation
• Material: STEEL
• Country of Origin: Made in India
• Color: SILVER

Owing to our rich industrial experience, we have outshined as a trustworthy name engaged in offering durable Automotive Shafts. Our team of highly qualified engineers uses cutting-edge technology to manufacture dimensionally accurate, sturdy and rigid Automotive Shafts. These Automotive Shafts are widely used in the automotive industry owing to their excellent tensile strength as well as abrasion resistance. We also manufacture Automotive Shafts as per the specifications laid down by the clients. Minimum Order Quantity : 1000 units

The CNC Turned Shafts, we offer, are widely used in electronic appliances, lighting, switches, sanitary, sanitary ware and more. Our CNC Turned Shafts can be availed in various surface treatments like anodizing, polishing, powder coating, sandblast, zinc/nickel/chrome plating, brushing, passivation, etc. We are one of the major CNC Turned Shafts Manufacturers and Suppliers in India.

Alternative jcb parts.

metal shaft, two wheeler indicator, Two Wheeler Brake Shoe

Pinion Bearing Preload Wrench, Loading / Unloading Ramp

Axle Shaft, Auto Gaskets, Shock Absorbers, Mudguard, Knock Sensor

auot shafts, Tractor Parts, Transmission Gears

Shafts, JCB TUBES, MAHINDRA METAL TUBES, Industrial Rollers

shaft, Brake Drum Couplings, Half Gears Coupling, Pendant Push Button

Shafts, Auto Parts, Bearing, housings product, Rope Drum, Sprockets

shaft, Clevis Pin, hub, Flange, Bushing, tee adaptors, Spacer

Changer Shaft, Hold Down Bracket, Joist Hanger

Cooler Motor Shaft, Ball Bearing Exhaust Fan Motors

motor shaft shaft, Shaft Collars, Bright Bars