Drawing Machine Dealers in Lal Kuan, Ghaziabad

Available with us is wide gamut of Industrial Coiler that is extensively demanded by our clients owing to its durability and reliability. Our product range is fabricated under the supervision of our experienced professionals using quality raw material in compliance with international quality standards. These are known for their robust construction, energy efficiency and corrosion resistance. Our product range is examined on defined parameters to eradicate all the flaws.  Dead Block Coiler   With our vast industry experience and competent workforce as our asset, we are able to manufacture and supply broad array of Dead Block Coiler. Our product range also comprises Dead Block Coilers for HC, MS, SS and non ferrous wires, ranging from 1mm-8mm. In order to achieve higher productivity, high drawing speed is not the only requirement, but uninterrupted production run of the machine is more useful. As a longer production run at a specified size is better for lower worker fatigue, it also provides higher coil weights that are useful in further processes.  

We, at Anant Enterprises, are a reliable Manufacturer and Supplier of premium Straight Line Wire Drawing Machine. We manufacture Straight Line Wire Drawing Machine strictly as per laid quality standards. This machine can efficiently draw any type of rod wires i.e. high / medium / low carbon steel, aluminum, copper etc. There is no scope of sliding or twisting with our Straight Line Wire Drawing Machine. Our Straight Line Wire Drawing Machine is majorly used for wood screw, nail, spring etc. The machine is electricity powered, thus quite safe to operate. It produces very low noise and performs flawlessly over period of time.

• Material: Cu./AI.
• Basic reduction %: 12/9

The wet draw machine is a slip type, straight line wire drawing machine which has become the standard of the industry for the production of carbon and alloy steel wires along with non ferrous wires. The wire enters the machine through the inlet by guide pulleys, through the first die and will exit the drawing compartment through the final die. Dies can be fully submerged. The die-holders are machined from solid steel. Optionally the machine is equipped to spray wet-lube directly into the die and onto the drawing capstans By doing this we do not have to wait for the tank to fill before we can start the line. The exit die is fully adjustable in all directions for easy setting of cast and helix. The machine can be connected to a central lubrication system. The fill and drain of the drawing compartment is quick and ergonomic ensuring a simple and mud-free die replacement. The machine can be supplied with pre drawing blocks for better accumulations Zenith production range includes wire drawing machines with 2, 4 or 6 independent cone arrangements with a range of 7 to 24 dies, for a finished wire diameter down to minimum 0,12mm

We offer technically advanced Bull Block Wire Drawing Machine which are vertical or horizontal and gravity bull block wire drawing machines with multi speed. These are facilitated with variable drives and are ideal for ferrous and non-ferrous wires.

• Type: Dry Wire Drawing Machines
• Features: high performance, low maintenance , long working life

• Brand Name: Assomac
• Operating Mode: Automatic
• Layout: Vertical
• Inlet size up to: 12mm

• Capstans: 200 - 1200mm
• Wire inlet: 2.0 - 30 mm

block wire drawing machines can be supplied in various model sizes and either with single draft , double draft or triple draft(triple die for aluminium rod). According to purpose of utilization they consist of finishing capstans or as pre- drawing capstans.The machine body is executed in heaviest mild steel construction.The capstan is made of a special cast and surface treated in the accumulation area to achieve a longer durability.

BLOCK AND COOLING SYSTEM : Drawing drums are forged alloy steel,fully hardened and ground.Surface hardness:58-60 HRC. Drums are internally water cooled with narrow gap system.Complete wetting of wall by highly tubulent motion of water,higher cooling effect with increasing drawing speeds. Drums are externally cooled by air from a single common blower through duct forming part of machine frame. DIES BOXES : Dies are direct water cooled from a separate manifold.Dies are loaded from top for quick fixing. Motorized rotating die holders can be provided; extra long to adopt standard pressure dies. Die boxes are equipped with motorized lubricant stirrer. Rotating die holders have single motor for stirrer and holder. Die boxes are adjustable in horizontal and vertical plane for cast and helix adjustment of wire. Die boxes are suitable for dry lubricants, large enough to store sufficient quantity of lubricant. SPEED CONTROL : Speed regulation of each block is achieved through self centering sensor arm on which the wire is guided. SAFETY GUARD : Well balanced sheet metal guards,with transparent shet/wire mesh to see through condition of machine,are provided. Guards are electrically interlocked not to allow running of machine with open guards. Sound proof guard for low noise level with suction of burnt powder can be provided. TRANSMISSION : Motion transmission from motor to block shaft is achieved directyl by V belt and pulleys or through helical gear arrangement. INTELLIGENT CONTROLS : Specially designed A.C. Three Phase Inverter Duty/Servo Motors L&T Supernova/Siemens 1ph7 constant torque upto base speed and constant power above base speed. Digital A.C. Three Phase Vector Flux Inverter Drives ABB ACS 800/Siemens Sinaemics provide the system with fastest communication through profibus. All blocks are working with a range of encoder feedback,thermal protection, flux vector controlled. The logic control is attained automatically by PLC system (siemens) automatically calculating reduction rate and mointoring all related dates. Utmost control flexibility allows any drafting programme and drum skipping. HMI displays all function data making it easier for the operator to take control of the machine during production. Displays and memorizes the fault for easy diagnosis. Can be interfaced with remote computer to collect all information. Cubicles are sheet steel enclosures with IP54 protection,duly power coated and with exhaust. Electric control system provides a smooth acceleration from zero to pre-selected value. Normal stop is attained with ramp down control within 15 to 30 secound. Emergency stop/quick stop is attained within 6 to 8 seconds. This can be achieved without a broken wire.

• Brand Name: Shivas
• Voltage: 240V
• Max Inlet Wire Diameter: 0-3 mm
• Frequency: 50Hz
• Application: Industrial
• Automatic Grade: Automatic

• Material: Aluminium
• Application: Wire Drawing machine
• Type: Vertical
• Automation Grade: Semi-Automatic

Wet MachinesMulti hold sub – merged type Wet Drawing Machine designed for all ferrous & non – ferrous metals in the range of 9/11/13/15/19/17/21/25 dies or as per Customer requirements with variable drives & speed. Rod Breakdown MachinesOur range of rod break down machine is manufactured as per the latest International usages. We also have facility to customize our range according to the client's requirements. These are available in various specifications, some of them are designed 9/11/13 die for aluminium and copper wires along with spooling machine and dead block coiler.

bull block wire drawing machine, Nails Making Machine, Binding Wire System

Straight Line Wire Drawing Machine, Strand Annealing Furnace

bull block wire drawing machine, Strand Annealing Furnace

Wire Drawing Machines, wet drawing machines, carbon dioxide wire plant