K. Engineering Meerut Road Industrial Area, Ghaziabad, Uttar Pradesh

Operating Parameters    Capacity (Maximum)                  1,000 m/hr.  Head (Maximum)                       100 m  Temperature                               80° C   Special Features  Vertical pumps take little space in plan since the liquid is led away to the axis of shaft.  The impeller is submerged, so pump does not required to be primed and is always ready for use.  The positive suction condition also prevents the cavitations in the pump and pitting in impeller and diffuser.  Due to positive head at suction the pump gives its rated performance as well as high overall efficiency. Design Features Glandless type and / or vapour sealing type execution available. In vapour sealing design, the gland and acid resistant asbestos packing prevents the leakage of vapours of hazardous liquids from coming out. Thus the environment is kept free from pollution and dangerous inflammable obnoxious liquids. Very rigid construction with extra wall-thickness provided for corrosive where fluctuations in liquid levels are considerable. The pump unit is suspended by a column pipe applications. It is virtually maintenance free. Vertical pumps are best suited for wet pit applications which also protects the transmission shaft and is submerged in the liquid to be pumped. These pumps require small floor area and can be started without priming. Discharge / Suction flanges conforms to ASA / DIN / BS standards.Delivery CASING : The delivery casing has an area sufficient enough to ensure easy passage of liquid with optimum efficiency.IMPELLER : The delivery casing has an area sufficient enough to ensure easy passage of liquid with optimum efficiency. Impeller : Impellers are enclosed / semi-open / open with large passage ways and thickened vanes at the inlet. All impellers are dynamically balanced. Closed type and semi-open type impeller designs are offered to handle a variety of liquids. Impeller are designed for maximum hydraulic efficiency and minimum thrust on rotating assembly. Unique space-saving design due to vertical mounting of pump. Impeller and casing are totally submerged in liquid so no priming or air venting is required. Inside tank and outside tank mounting designs available for respective applications. Pump Shaft :  The pump shafts are of high tensile carbon steel and designed for high torque transmission. Stainless steel shafts can be provided against requirement. The bearing areas are protected by stainless steel sleeves. Intermediate, line and head shafts are of ample strength and rigidity. Minimum bearing span is adopted to keep deflection and vibration to a minimum.Line Shaft / Intermediate Shaft : Line shafts / intermediate shaft of high tensile carbon steel designed for high power transmission are connected by intermediate couplings and run in closely spaced bearings for vibration-free operation.Motor Stool : The heavy duty cast iron / mild steel motor stool is capable of taking the motor and rotor assembly weights as well as the axial thrust. It also houses the thrust bearings.Intermediate Bearings : The transmission bearings may be lubricated by one of the following methods:1. External supply of clear cold water.2. By liquid being pumped.3. Grease External clear water lubrication is recommended when it is available at a pressure higher than the discharge pressure of the pump. If the pumped liquid has a turbidity of less than 50 ppm (silica scale) or 500 ppm (chloride scale) and total solids less than 3000 ppm with pH value between 6.5 and 8.5, then it may be used as the lubricating liquid. Grease lubricated bearings are recommended when external or self lubrication is not possible. Grease is supplied by a grease pump driven either through the pump coupling or by a separate motor. Angular contact ball bearing at the top to take residual axial thrust and the weight of rotating parts.Delivery Pipe : Heavy duty delivery pipe upto the motor stool floor level with one bend is standard supply with all.Accessories : The following accessories are recommended.1. Screens at inlet of the sump to prevent solids of sizes larger than that recommended from entering the pump.2. Liquid level controllers to guard against dry running of the pump.3. Power operated positive displacement grease lubricator for grease lubricated pumps.4. Delivery pipes and bend upto the motor stool.Salient Features  Compact design, easy to install  Extra heavy shaft  Screenless, chockless and glandless design  Also available in dry pit designs Areas of Application  Dewatering applications where water is contaminated with solid particles  Raw sewage, slurry  Effluent, industrial waste transfer in industrie's Waste water  Drainage of basements, tunnels, boiler rooms  Storm water Construction Material Other than above stated material pumps are available in Cast Steel, CA 15, Ni-Resist, Super Duplex, CN7M, Haste alloy and other special stainless steel alloys. The materials of construction are offered as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pumped. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.

Operating Parameters    Discharge Sizes                  N.D. 25 - 400 mm  Capacity                             Upto 1200m/hr.  Head                                  Upto 60 Mtrs.  Solid Handled                      Upto 200 mm   Special Features  Un-obstructed passage to the discharge size of the pump.  Handles large solids & long fibres.  Gentle pumping action, no flows / crystal damage.  Low leakage  Low maintenance cost, no sealing rings on impeller, no small clearances to be maintained.  Handles abrasive slurry.  Handles vulnerable products like vegetables, fish, crystals etc.  Hydraulically balanced construction. Design FeaturesCasing: Smooth extra heavy section designed for unobstructed free flow. Abrasive or solids-laden flow goes directly into vortex of liquid and out the discharge. No close clearances between casing and impeller (as in conventional pumps) to generate wear. Nothing between suction and discharge to jam, clog, break or bind... a totally non-clog concept in pumping. Impeller : Impeller, fully recessed out of flow path, is not subjected to wear by solids or abrasive particles churning in the flow when handling solids or slurrie greatly improving impeller life. Impellers may be threaded to shaft to provide shaft end protection.Shaft : Heavy duty shafts are designed for maximum operational heads and low deflection and vibration. Shaft Sleeve: Shaft sleeve is keyed to shaft and gasket sealed to stop leakage under sleeve.Stuffing Box: Designed for gland packed arrangement fitted with neck bush and has been provided with external fluid sealing connections which enhances life of gland packing. Mechanical seals can also be provided.Bearings: Angular contact ball thrust bearings carry radial and thrust loads. Thrust bearings are back to back mounted, locked with nuts and lock washers. Oil lubrication is standard. Constant level oiler maintains proper oil level. Bearings are well protected from dirt. Grease lubrication can also be provided. Exclusive AdvantagesFree Passage : The recessing of the T.F. Pump impeller permits unobstructed passage through the pump casing.Non-clogging : Solids up to the full diameter size of the discharge connection can pass through the pump without danger of clogging. Also long fibrous materials will cause no problems.Long Life : The robust and simple design as well as the correct materials for the job guarantee long service life. Simple Design: The simple open and concentric design guarantees a trouble free service even under extreme conditions.Wear Resistant: The new T. F. Pump casing (axiaspiral) ensures that the solids entertained in the flow are quickly discharged from the pump and thereby reducing abrasion.Low Maintenance: More than 20 years experience in production and application of T.F. Pumps has shown that the Torque Flow Pumps need less spares than any comparable solids handling pumps. Construction Material The materials of construction are indicated as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pumped. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.

Operating Parameters    Capacity (Maximum)                  8000 m/hr.  Head (Maximum)                       160 m  Temperature                             110°C  Working Pressure kg/cm'           18 kg/cm   Special Features This range provides a higher efficiency with lower maintenance. Development of this new range followed an extensive consultation with major users. This has produced an advanced pump which provides total reliability and reduced life cycle cost. We utilizes the well-proven "lean production system". This single flow,lean manufacturing process with dedicated production units means less wastage and greater efficiency, enabling us to provide the highest standard pumps and components. Design FeaturesImpeller : Impeller is firmly secured to the shaft by a key positioned by shaft sleeves and both locked in place by shaft sleeve locknuts external to the stuffing box.Shaft : Machined from high quality steel. The shaft is sturdily proportioned to minimize deflection and provide long reliable service. Sleeves : Sleeves are provided to protect the shaft and ensure longer shaft life. Neck Ring : Designed with appropriate clearances and materials to minimize leakages while ensuring a long impeller life. Improved Hydraulics : Unique hydraulic passage design for optimum performance.Stiff Shaft Design : Large diameter shaft supported on a short bearing span minimizes shaft deflection, prolonging seal and bearing life. Simple Maintenance : Standard pumps cartridge bearings and seals can be removed without displacing top half casing.Increased Component Life : More corrosion allowance offers better corrosion protection and optimum lifetime operation. Enhanced Performance : Replaceable wear ring and bush reduce leakage. Increased Efficiency : Standard pumps coating on casing internals optimizes performance and prolongs "as new" efficiencies. Low Hydraulic Loads : Diametrically opposed volute design reduces hydraulic loads extending seal and bearing life.    Salient Features  Compact design, easy to install.  Extra heavy shaft  Both side bearing supported  Stable and robust design Areas of Application  Condensate  Cooling Tower  Service Water  Injection Spray  Fire Fighting  Sprinkler System  Cool Washing Construction Material Other than above stated material pumps are available in Cast Steel, CA 15, Ni-Resist, Super Duplex, CN7M, Haste alloy and other special stainless steel alloys. The materials of construction are offered as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pumped. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.

Operating Parameters    Capacity (Maximum)                  6,000 m/hr.  Head (Maximum)                       45 m  Temperature                             90° C  Working Pressure kg/cm'           4 kg/cm   Special Features KMF Pumps are normally recommended for clear cold water having turbidity maximum 50 ppm (Silica Scale),chloride maximum 550 ppm. Total solids 3000 ppm. pH value between 6.5 and 8.5 and specific gravity around 1.0. KMF pumps can be offered for liquids having viscosity upto 1000 SSU. These are three / four vane impeller pumps specially designed to pass solid or stingy material. Hand holes are provided in the casing and near the throat of impeller. Pumps are available in Horizontal construction, vertical dry pit or wet pit construction with motor directly mounted on the pump or at an elevation and connected through intermediate shaft. Design FeaturesCASING: Pump casing is high strength cast iron with ample section thickness to produce a large factor of safety over the maximum permissible working pressure. The casing is enclosed by a suction and stuffing box over or head carefully machined to assure perfect alignment. Suction and discharge nozzles and the supporting feet are cast integral with the casing. All flange are drilled according to BS 10 table D.IMPELLER : The impeller of KMF pumps are made of SS 304. The impeller is semi-open type having wide passages into which the liquid flows direct and unimpeded. The impellers are provided with balancing holes for balancing the axial thrust. They are also dynamically balanced to counter the vibrations. Impellers in other materials such as close grained cast iron, Bronze, phosphors bronze Ni-cast iron, cast steel etc. are also available on request. Bearing Housing Assembly : The rotating assembly is supported on heavy duty bearings mounted in a precision bored frame. Bearing are carefully sealed to exclude moisture and contaminants and retain lubricant.Stuffing Box : Extra deep design and features a gland to simplify replacement of gland packing. Packed stuffing box with lantern ring is the standard arrangement. It is sealed internally. However, against special requirement, sealing by external fluid is also provided.Shaft : Machined from high quality steel, the shaft is sturdy design to minimize deflection and provides long and reliable service. Shaft is protected by sleeve from wear in stuffing box area.    Salient Features   The KMF series are single-stage centrifugal pumps suitable for handling pure or contaminated liquids in large quantity. These pumps are of robust construction and have long working life. These pumps are also low in energy consumption due to very good efficiency. The precision machined pump shaft is seated in amply oil/grease lubricated bearings and protected by a shaft sleeve in the stuffing box area. The integrally cast feet of the casing transmit any forces originating from the pipework directly to the foundation, this means that the rotor is not subjected to any bending stresses and thus optimal working life of the bearings is assured. Electric motors can be used as the prime mover. With diesel engine as the prime-mover, the pump's direction of rotation is anti clockwise from the driven end.   Areas of Application  Cooling Water  Water treatment  Injection and Spray  Condensate  Water supply  Cooling Tower  Storm water and Drainage  Sewage Disposal  HP/LP  Recirculation Construction Material The materials of construction are offered as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pumped. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.

Operating Parameters    Capacity (Maximum)                  1000 m'/hr.  Head (Maximum)                       140 m  Temperature                             160° C  Working Pressure kg/cm'           14 kg/cm   Special Features  Jacketed convertible stuffing box utilizing gland packing or mechanical seal.  Special designed stainless steel impeller nut with helical spring insert to lock the impeller properly.  Back pull out type bearing frame assembly.  Mechanically & hydraulically balanced impeller for long life and high efficiency performance.  Heavy duty shaft with maximum deflection less than 0.05mm.  Heavy sections to withstand high pressure and temperature. Design FeaturesShaft Design : Designed for toughest services. Maximum 0.05 mm deflection at stuffing box face at maximum load. Balancing of Impeller : Hydraulically and Mechanically Balanced Impeller. Axial thrust balance achieved by front and back wearing rings with balancing hole / back vanes for operation over wide range of suction pressure.Versatile Shaft Seal :   By gland packing. Option to use standard unbalanced / balanced mechanical seal. Robust Deep Groove Ball Bearings :   High operating reliability, grease / oil packed.Better Interchangeability :Ensures fast delivery and low inventory.High Performance :Lower noise and less vibration levels Mechanical Seals :Various mechanical seal configurations are available. A single mechanical seal is used for many applications with no circulation liquid, flushing with internal / external circulation liquid or with grease is available. For extremely demanding liquids and application, double mechanical seals can be selected. Sealing liquid from an external source is required. Gland Packing :   Gland packing with external flushing prevents the pumped liquid from penetrating into the seal housing. The pressurized flushing liquid causes it to flow into the pumped liquid. Alternatively the external flushing liquid can have a separate outlet connection. Salient Features   Back pull out design permits quick and easy access to rotating parts without disturbing suction and discharge pipes, electric motor, its connections and alignment. Low maintenance, inventory and standardization because of module system. The pump is designed to achieve a low NPSH requirement and high efficiency. It is rugged in construction and is versatile in application. This series is designed in accordance with ISO 5199 / ISO 2858, making it ideal for worldwide chemical or industrial process applications.   Areas of Application  Condensate  Service Water  Injection / spray  DM Water Transfer  Chemical Transfer  Circulation  Portable water Construction Material   Pumps are also available in Cast Steel, Ni-Resist, Super Duplex, CN7M, Haste Alloy and other special stainless steel alloys in addition to mentioned above. The materials of construction are indicated as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pump. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.

Operating Parameters    Capacity (Maximum)                  10,000 m /hr.  Head (Maximum)                       40 m  Temperature                               50°C   Pump Introduction K Engineering range of vertical pumps offer widest range of selection depending upon the pumping liquid from Clear Water to varying degress of contamination. Hydraulic design of these pumps are based on most valuable and up to date technologies and experience available in the field. These pumps are designed to operate at 50Hz or 60 Hz, in single or more than one stage according to Head required.These pumps consisting of Bowl Assembly, Column Pipe Assembly, Bearing Housing Assembly along with N.R. R. (Non-Reverse Ratchet) Assembly & Motor Stool / Driving Unit Assembly. Bowl Assembly consists of suction bell, impellers, bowls, and pump shaft.Suction Bell designed for smooth & steady entrance of liquid with minimum losses. The Bowl is a casing with diffuser vanes cast integrally to reduce the velocity of the liquid coming from impeller & increasing the pressure.Impellers are of open (propeller), semi-open (mixed flow) & enclosed (vertical turbine) type depending upon the specific speed of pumps and are accurately machined, dynamically & hydraulically balanced. The shaft is of high tensile strength steel.Column Pipe Assembly consist of column pipe, line shaft & line shaft couplings and bearings. Column Pipe casted or fabricated, it houses line shaft bearing retainer.Line shaft bearing provided in leaded bronze shell with cutless rubber (natural / synthetic) bearing lubrication self or pressurized external water. Thrust Bearing Assembly anti friction bearings are provided to take care of axial thrust & weight of rotor assembly as well as radial load. Lubrications with oil / grease. Non reverse ratchet is provided with thrust bearing housing assembly to avoid the rotation of impeller (pump) in opposite direction causing opening of the threaded coupling. Either cast or fabricated designed to direct flow from column pipe to discharge pipe. It may be at ground level or below ground level.Discharge Head/Discharge Elbow : Either cast or fabricated designed to direct flow from column pipe to discharge pipe. It may be at ground level or below ground level. Motor Stool : M.S. fabricated heavy duty to ensure vibration free operation. Couplings : For line shaft, threaded barrel or muff type coupling as per requirement. For pump to motor, pin bush flexible coupling is provided.Direction of Rotation : Counter clock wise when viewed from driving end. Areas of Application  Main Cooling Water and Auxiliary  Cooling Water Applications  Spray and Injection Water  Cooling Tower Circulation  Cooling Water Pumps, HP/LP Water  Pumps Condensate and Misc. Services  Pumps in Power Plants  Fire Fighting Construction Material Other than above stated material pumps are available in Cast Steel, CA 15, Ni-Resist, Super Duplex, CN7M, Haste alloy and other special stainless steel alloys. The materials of construction are offered as an example of generally accepted practice, but are not intended as recommendations of fitness for a particular purpose. The customer must determine and take the ultimate responsibility for specifying the proper materials to handle the particular fluid pumped. Unless otherwise specified, all pumps shall be furnished with the standard fitted materials to meet the system requirement.