Angle Seat Valve Dealers

• End Connection: Screwed / Flange / Tri-Clamp
• Body Material: SS ASTM A351 Grade CF8 / CF8M
• Seal: TEFLON / VITON / EPDM / SILICON
• Circumstance Temp: -10°C to 70°C
• Media Temp: -10°C to 180°C
• Media: Steam, Air, Water, Chemical, Gases, Oil, Diesel, Hot Water
• Cover: SS304
• Plate: Aluminum Die-Cast
• Working Pressure: 3.5 to 7 bar air (Not recommended actuator pressure above 7 bar)
• Life: More than ten million cycle

We are offering angle seat valves.

• Material: Stainless Steel
• Color: Silver
• Application: Steam Trap Valve
• Feature: Fine Finished,Good Quality,Good Strength,High Flow Rate,Long Life,Long Service Life,Rust Proof
• Type: Valve Sheet
• Country of Origin: India
• Brand Name: STOLZEL
• Size: 25MM

An angle seat piston valve is a pneumatically-controlled valve with a piston actuator providing linear actuation to lift a seal off its seat.

• Size: 40MM To 50MM
• Type: 2 Way
• Actuator: SS304 Pressure
• Valve Body: IC CFB / IC CFBM
• Working Parts: CF8
• Seat: PTFE
• Working Pressure: Upto 16 Bar
• Pneumatic Pressure: Upto 3.5 to 7 Bar
• Temperature: Upto 180 Degree C Maximum
• Leakage Class: Bubble Tight Shut Off
• Media: Air / Steam / Water/Gas /Oil /Chemical
• Ends Connection: Screwed End BSP (F)

・For steam (Can be used with air and water.)・Low pressure loss due to angle seat structure・Reduced leakage with rubber seal・Long service life: 3 million cycles (Steam), 5 million cycles (Air)・Low leakage: 10 cm3/min or less・Space saving: Height 100 mm・Body material: Stainless steel 316L equivalent, Bronze (CAC)

• Material: IC CF8 / CF8M
• Power: Temperature : Upto 180C
• Pressure: Upto 10 Bar
• Application: Gas Fitting, Oil Fitting, Water Fitting
• Size: 1/2inch, 1inch, 2inch, 3/4inch, 11/4", 11/2"
• Type: Y Type Angle Valve
• Country of Origin: India
• Media: Air, Water, Oil, Gas and Steam
• Temperature Of Media: Upto 180C

Model : SRTBody : IC CF8 / CF8MSeals : PTFEPressure : Upto 10 BarTemperature : Upto 180CLeakage Class : Class VIMedia : Air, Water, Oil, Gas and Steam   Key Features: Precise Flow Regulation: The Pneumatic Y Type Control Valve operates on a quarter-turn principle, allowing accurate and precise control of media flow. Its hollow rotating ball design ensures smooth and efficient flow regulation, making it suitable for critical processes.Wide Range of Sizes: Our valve comes in multiple sizes, including 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″, and 2″, catering to various flow requirements and installation needs.Multiple End Connections: Choose between Flange End and Screwed End connections based on your installation preferences and system requirements, ensuring a seamless integration process.Durable Construction: The body of the valve is constructed from high-quality IC CF8 or CF8M stainless steel, providing excellent corrosion resistance and structural integrity.PTFE Seals: Equipped with PTFE seals, the valve ensures a reliable and tight shut-off, achieving Leakage Class VI standards for minimal media leakage.High Pressure and Temperature Capability: Our Pneumatic Y Type Control Valve can handle pressures of up to 10 Bar and temperatures of up to 180°C, making it suitable for demanding applications.

• Country of Origin: India
• Size: 1.1/2inch
• Type: Angle Seat Valve
• Material: Stainless Steel
• Certification: ISO 9001:2008 Certified
• Application: Oil Fitting
• Color: Black
• Feature: Durable
• Pattern: Plain
• Automatic Grade: Automatic
• Pressure: High
• Number Of Way: 2way
• Brand Name: Rotex

• Brand Name: VZXA

The VZXA easily adapts to the task in hand thanks to its range of variants, thus maximising flexibility and minimising the effort involved in designing your application. The carefully thought-out product architecture with its easy-to-clean design means valve bodies and actuators can be freely combined. The modular product concept makes it easier to modify and maintain systems without having to remove the entire valve. Modular Robust and easy-to-clean stainless steel process valve The actuator can be replaced without opening the piping (unpressurised) 22-way valve in DN13 (½") � DN65 (2½") Actuator modules as piston or diaphragm actuator: single or double-acting

• Media: Air, Water, Oil, Gas and Steam
• Material: Stainless Steel
• Valve Size: 1 Inch
• Packaging Type: Box
• Material Grade: SS316
• Finishing: Galvanized
• Temprature Range: -10

• Material: Aluminium and Stainless Steel
• Model Number: 12040, 12050, 12063, 20050, 20063, 25050
• Connection Size: 1/2", 3/4"

The 304 Stainless Steel Pneumatic Angle Seat Valves, which we supply, are reckoned for being accurate in terms of structural accuracy.Advanced transportation facilities, efficient workforce, on time delivery of the products make us stand out from the crowd. We have with us a well-maintained and capacious storage unit that is facilitated by advanced and automated warehousing system, which is operated and supervised by experts only.

• Media: Liquid, Gas, Steam, LPG, Water, Oil .
• Model: 12050V01
• Normally Close Above Plug: 0-25
• Normally Close Below plug: 0-16
• Orifice Size (mm): 12 Port
• Connection: 1/2″ MOC: CF8 (SS304 Cast) | CF3M (SS316L Cast)
• Solenoid: Weather Proof | Explosion Proof | Intrinsically safe
• Certificate: ATEX, CCOE/PESO, CUTR-EAC, IEC Ex, INMETRO, UKRAINE, CE, UL
• Fuel Application: Medical Sterilizers,Auto claves, Foods & Beverages – Boiler Steam control, Water treatment plant , Textile Dyeing & Drying, Bottling & Dispensing equipment,Ink & Paint Dispensing, Laundry Equipments

Spring return closed or open, double-acting Stainless steel valve body standard (SS316) High flow rate Optical visual indication Low control air consumption due to minimized volume in the actuator

Angle Seat Valve : Sub base mounted valves. Manual Reset, Latch Type, Intrinsically Safe, Low Power, Redundant. Bag Filter – Pulse Jet valves, Gas Over Oil Cabinet Valves.

We are offering angle seat valve.

• Power: 24V DC
• Features: Easy conversion from Single Acting to Double Acting, Modular Design, multiple Operator option possible on the same valve Body,
• Pilot Connection: Threaded Namur
• Brand: Rotex
• Model: 12040
• Connection Size: 1/2-1 inch
• Pilot Pressure: 3- 7 Bar
• Ambient Temperature: 0 - 55 Degree C
• IP Rating: IP65

Application Rotolock valves are Compatible with all CFC, HCFC and HFC Refrigerants, mineral oils, Alkyl Benzene, POE lubricants and Industrial fluids non-corrosive to steel and brass. (With suitable Gland/Seal). Materials of construction Valve Body: Hot Forged Brass (BS-218). Spindle: Stainless Steel 304. Gland Nut: Free cutting Brass Gland Packing: Graphite and Neoprene Seal Cap: Plated steel / ABS Seat : Stainless Steel 304 Design Forged Brass body and SS 304 internal components minimize chances of porosity and corrosion in all conditions and allow easy brazing with copper tubes. Spindle with full back seating and special graphite seals allow gland packing to be changed in open position and brazing without disassembling the valve. Brass body and SS 304 floating internal seat allow metal to metal seating on dissimilar metals resulting in positive isolation and virtually lifelong durability. Operation & Testing. Maximum working pressure 450 psig. Working Temperature Range: (-30°C + 100°C). Individual pneumatic Testing in Open/Close position at 450 psig. Valves suitable for operation at 650 psig can also be provided on request.

The angle valve is pneumatically operated and extremely reliable. They guarantee a high number of working cycle as well as bubble tight sealing. They are installed with self lubricating and self adjusting plug stem set that automatically adjusts its self as it. The self align plug with a seal in PTFE, guarantees tight closer even in the most arduous condition. Technical Characteristics Technical Characteristics Air, Water, Oil, Petroleum products, steam, etc. (as long as compatible with AISI 316L or PTFE). Pressure from 0 to 15 bar (Steam from 180 0C from 0 to 10 bars). Depending on the size and model. Temperature from -10 0C to 180 0C. Max Viscosity 800 cst (mm2/s). Control Media Driving media: compressed air, lubricated or dry, gas or neutral media. Ambient temperature: -10 0C to + 60 0C. General Feature Body Valve Material: Aluminium LM/4. Valves Ends: Screwed / Flanged. Assembling is possible in all position: upright, flat or angled. Range available from DN-25 to DN-50 in double acting versions, spring return N.C. from above and below the plug, spring return N.O. from below the plug.

An important component in many process applications for 2/2 function, installed in line Suitable for viscous & dirty media & high temperature and has high flow rates. It is poppet design with spring return.

• Material: Stainless Steel
• Pressure: Medium Pressure
• Media: Water
• Country of Origin: Made in India
• Usage/Application: Industrial
• Valve Size: 1/2 to 2 Inches
• Temprature: 180 Degree C

 NC/ NO/ Bi-Directional• Can be easily converted from NC to NO/ Double Acting to Single Acting• Operator with threaded/ NAMUR ports• Lubricated pilot air not necessary• Ideally suited for vacuum service• Fast acting up to 1000 cycles/ hour• Wetted parts : CF3M (SS 316L cast), SS 316L• Life > 10 million cycles• Modular design

• Material: Stainless Steel
• Pressure: Medium Pressure
• Media: Water
• Country of Origin: Made in India
• Valve Size: Upto 80mm
• Temprature: Upto 180 Degree Celsius

• Material: Stainless Steel
• Brand Name: Uflow rotex
• Media: AIR, WATER
• Country of Origin: Made in India
• Valve Size: 1/2 TO 2 Inches
• Product Type: Y type valve
• Packaging Details: SINGLE PIECE BOX

Our team members and quality auditors keep regular checks on the quality of products and thus, even the raw material used is tested under vigil supervision to ensure better quality products. Made using superior grade materials, our products are quality assured and as per international industry standards. Features : High grade metallic structure Easy to install QC tested

• Size: 1/2″ to 4″ Screwed / Flange
• Media: Air, Water, Oil, Gas, Steam & Chemical
• Body: ASTM A351 Gr. Cf8 / CF8M / CF3M
• Steam Packing: PTFE upto 180°C, Self-compensating (Spring Loaded)
• Trim / Spindle: Stainless Steel 304/316/316L
• Seat: Soft Seat (PTFE)
• Gland Packing: Teflon ‘V’ seals, backed by graphite wiper seal (Self Compensating)
• Body Test Pressure: 24 Bar Maximum
• End Connections: Female Screwed to BSP or NPT / Flange / Triclover
• Working Fluid Press: Refer to table
• Leakage: Drop tight / bubble tight, class IV ANSI B 16, 104, 1976
• Operating Temp.: On steam – Continues 155°C, Intermittent 180°C Maximum (High Temp. above 180°C – On Request)

• Material: MS
• Media: Air, Water
• Pressure: 3.5 to 7 Bar
• Finishing: Color Coated
• Temperature: 250 Degree C

Features Spring return closed or open, double-acting Stainless steel valve body standard (SS316) High flow rate Optical visual indication Low control air consumption due to minimized volume in the actuator

• Connection: Threaded(BSP, NPT), Welded, Flanged, Clamp End
• Control Type: Normally closed, Normally open, Double acting
• Ambient temperature: -10ºC to 80ºC
• Fluid temperature: -10ºC to 180ºC, 25ºC to 220ºC
• Applicable Fluid: Water, Alcohol, Oil, Dye, Steam, Neutral gas or liquid, Organic solvent, Acid and lye
• Actuator Size: 50mm, 63mm, 80mm, 90mm, 125mm
• SS316, Wcb: 150/PN16, 300
• Double Acting, Spring Return: 1", 2", 3", 4", 5", 6"