Compu Power Private Limited Banjara Hills, Hyderabad, Telangana

Compupower provides Connectorized Data Bus Couplers with Single, Dual, Four and Six Stubs. These Couplers are available with and without internal terminations.  All resistors are 1Watt per MIL-R-39007 and mounted away from the transformer to minimize heating effects.  The transformers are manufactured to MIL-T-21038.  All Couplers are 100% tested and certified.    Features:                   1Watt Isolation resistors 1Watt Terminating resistors -55°C to +125°C operating temperature.   Benefits: Qualified  and type approved for flight applications Low cost Highly reliable Bast delivery

we have designed and developed Data Bus Interface Transformers to meet the requirements of MIL-STD-1553B Data Bus applications. We believe our line of Data Bus Couplers and Transformers to be the best in terms of performance, cost and reliability.

Compupower Private Limited, over the years has earned the recognition of Indian Defence industry for its capability to produce highly reliable Data Bus Couplers for MIL-STD-1553B applications. With this capability and knowledge, we have designed and developed Data Bus Interface Transformers to meet the requirements of MIL-STD-1553B Data Bus applications. We believe our line of Data Bus Couplers and Transformers to be the best in terms of performance, cost and reliability.   Applicable documents: MIL-STD-1553B MIL-STD-202 MIL-T-21038D   Features: High Reliability 45dB Common Mode Rejection Low cost All Standard Voltages & Turns Ratios Fast Delivery

All measurements are PassFail type tests with proper LED indications. By means of five push-to-test switches, tester can detect shorts, opens, shorts to shield and phase reversal (cross over) on the Bus and Stubs. Easy to use hand held battery operated equipment ™ Low cost, light weight and easy to use by single person ™ Fast and easy testing with GoNo-Go LED indicators ™ Required no Main Bus disconnection

The DBR 5000 series developed by Compupower are designed for switching LRUs or RTs from one Bus or Stub to another or reconfigure a Bus. These switchers are Double Pole Double Throw (DPDT) relay devices, which act as ON-OFF Bus switchers to disconnect individual RTs or entire Bus segment from a Bus Network eliminating the task of manually disconnecting cables. Reconfiguring of a Bus is accomplished by applying 28VDC to the relay devices using D-subminiature connector. The Bus switching relays are energized just prior to separation by the aircraft or launcher controller. A problem that occurs in separable stages in launch vehicles is an open Bus or Stub at the time of separation. One solution to this problem is use of Data Bus Relay Devices. The idea is reconfigure the critical Bus(s) into valid Bus configurations by physically disconnecting from the exposed open leads and switching in a proper termination.   Applications: Switching between two Buses. Switching an RT ON or OFF from a Coupler Stub. Segmenting a Bus between a controller and two RTs allowing either terminal to be addressed by the controller.   Benefits: Ideal for test and simulation No cable changing Easy to use  

Material : CRCA steel with Tin plating.

The Couplers with cables attached are known as In-line Data bus Couplers. Compupower provides In-line Data Bus Couplers with Single and Dual Stubs. These Couplers are available with and without internal terminations and are for use in applications where mounting can be accomplished by wiring the Coupler into the harness. Data Bus Couplers can be supplied with a variety of connectors and cables (10614-9 or MIL-C-17/176-00002) or without connectors for splicing or integrating into harnesses. Couplers can be ordered with custom cable lengths and a variety of connectors for direct installation on any system. Using In-line Couplers in Harness/Network reduces the number of connectors which significantly improves the reliability. All resistors are 1Watt per MIL-R-39007 and mounted away from the transformer to minimize heating effects. The transformers are manufactured to MIL-T-21038. All Couplers are 100% tested and certified. For maximum system reliability, several Couplers can be connected in series (chain linked) as harness with no splices.   Features: 1Watt Isolation resistors 1Watt Terminating resistors -55°C to +125°C operating temperature.   Benefits: Qualified and type approved for flight and space applications Low cost Highly reliable Small and lightweight Fast delivery Can be supplied as a complete harness as per customer specifications

The main feature of this Tester is that, these tests can be performed from the LRURT ends of the Stub cables because, access to the Couplers and Main Bus itself may be difficult.Easy to use hand held battery operated equipment

These Couplers are available with and without internal terminations and are for use in applications where mounting can be accomplished by wiring the Coupler into the harness. Qualified and type approved for flight and space applications ™ Low cost ™ Highly reliable

Couplers can be ordered with custom cable lengths and a variety of connectors for direct installation on any system. Using In-line Couplers in HarnessNetwork reduces the number of connectors which significantly improves the reliability.

All Couplers are 100% tested and certified. For maximum system reliability, several Couplers can be connected in series (chain linked) as harness with no splices.Qualified and type approved for flight and space applications Low cost Highly reliable Small and lightweight