Just Beyond Technologies Jubilee Hills, Hyderabad, Telangana

SOUTH YCRP40 mobile zero-emission Wet concrete recycling system is the best solution to recycle remaining in concrete mixing station and the remaining concrete from concrete plant and mixer after washed. It can separate sand, soil and grave permanently and utilize the waste water to produce, realizing zero-emission of waste water and waste material. It is a common problem in traditional commercial concrete business that grout is flowing everywhere and waste concrete accumulate. According to statistics, when producing 1 million m3 concrete, the waste amount is equal to 2500m3 concrete and the water wasted made by cleaning equipment reaches 50t. The waste water in the mixing station contains strong caustic materials such as cement hydration product and residual admixture and its PH value is over 13. It will do great damage to surrounding water and soil. It has been standard equipment for a commercial concrete business to have a recycling system. YCRP40 wet concrete recycling equipment developed by SOUTH has 5 characteristics as follows. The customers will feel the high-efficiency and convenience of wet-mixing recovery, with energy-saving and environmental protection.

The workshop-type dry mortar mixing equipment developed by SOUTH is used for special mortar production. The material feeding method and the raw material storage system of the equipment located in workshop vary according to customers' products and plant conditions. The small-size equipment requires a few types of power silo and a small container volume, and therefore a low output of mortar with single variety is achieved and a low investment is needed.

The warm mix asphalt technology refers to the asphalt mixture technology which is used to carry out asphalt mixing and operation at a low temperature through certain technical measures and maintain its performance not less than hot asphalt mixture at the same time. The mixing temperature is between hot asphalt mixture (150℃-180℃) and cold (room temperature) asphalt mixture, while the performance reaches (or close to) hot asphalt mixture. This technology is applicable to all grades of highway asphalt pavement and building layer, and its wide appliaion value shows in the areas with high air quality requirements (such as tunnels). In addition, this technology is to make asphalt foamed, expand the volume and significantly decrease the viscosity by adding water, which finishes coating with the aggregate at a low temperature, thereby performing the mixing and operation at a low temperature to reduce pollution emissions. After evaporation of water, asphalt recovers to its original physical properties, with the added water content being about 2% of the asphalt mass.

V7 dry-type sand making equipment developed by SOUTH makes breakthroughs in the vertical-shaft crushing, air screening and other key technologies and uses the five-hole impact rotor structure, the state-of-art technology to crush, shape and grind raw materials entering crushers through rotors using the "rock breaking" centrifugal crushing method. This achieves self-generated crushing and high-strength self-generated crushing, thereby efficiently improving the particle shapes of finished sand and increasing the output of fine aggregate. The equipment uses the air screening technology to achieve perfect classification on transfinite particle size, finished sand and sand powder, thereby maximizing the screening efficiency, and uses intelligent control to make the fineness modulus of finished sand adjustable. In addition, the equipment uses the dust collector technology with offline ash removal pulse to efficiently control the content of rock flour in finished sand and operate the whole system in a closed negative pressure environment, thereby realizing the value ideas of green and intelligent sand making for environmental protection.

The three-hole impact enclosed rotor is adopted to realize the crushing and forming of the materials entering the crusher through the principle of stone-hit-stone and self crushing. Meanwhile, crushing and forming of big particle can also be realized.

Track mobile screening station can be used in quarries, mines, construction demolition debris handling, surface soil treatment, material recycling, sand sieving, coal mines and aggregate sieving and so on. ®SOUTH 694+E is an industry leading track mobile screening equipment. It has the characteristics of high productivity, quick installation, and easy maintenance, etc.694+E still chooses the world famous brand water-cooled engine according with Tier3 (discharge standard). In addition, it is equipped with 2 sets of 30kW motor drive system. After connecting the external power, it provides the equipment with operating power. ® SOUTH 694+is an industry leading track mobile inclined sieving equipment. It has a first-class producing level, the shortest installation time and the most convenient operation. ® SOUTH 683’s performance and productivity are famous in the world. It has functions of pre-screening and stacking. ® SOUTH 984 track mobile horizontal sieving equipment has three-layer horizontal screen mesh. It is easy to install, strong power, and is the ideal choice of quarry, mining and recycling other large-scale material processing industries.

SOUTH tracked mobile reaction crushing station has four types. ®SOUTH I-130 is designed for quarrying, mining, solid waste recycling and reusing.I-130RS has the crushing and screening functions. It is added a 4,270x1,520mm single-layer sieve-sieve box which can be quickly disassembled.®SOUTHI-11 is a medium-sized reaction crushing station. In the quarry, mines and solid waste recycling, it provides the owner with excellent crushing ratio and the product particle type with a high consistency .®SOUTHI-111 based on the I-111 is added a 3 350mmx1 525mm loop sieve, double-layer screen sieve box and feeding belt conveyor which is used for sending the over-sized material back to the host.

SOUTH tracked mobile jaw crushing plant has five models, among which, ®SOUTH J-1480E and J-1175E are the oil-electricity dual-use tracked mobile jaw crushing plants, with the characteristics of large production capacity, high cost-effective performance, energy-saving and environmental protection and with unparalleled advantages on the aspects of production efficiency, stability and cost savings for the users in various types of appliaions. ®SOUTH J-1480 is equipped with ® Jaques JW55 single toggle jaw crusher main body, with the maximum output of the handled materials up to 750th. In a range of appliaions, ®SOUTH J-1175 can provide the best production output and is an ideal equipment for quarrying, mining, solid waste recycling and reuse.®SOUTH J-1160 is a tracked mobile primary jaw crushing plant with compact structure and good performance, times-saving installation, convenient transportation and user-friendly operation, which is an ideal machinery equipment for all kinds of materials operators.

SOUTH tracked mobile cone crushing station has six models. Oil-electricity dual-use tracked mobile cone crushing station is a new product of SOUTH . Its power driven crushing operations can save energy costs, and reduce the maintenance cost of the hydraulic system. C-1550 has ®1300 cone crushing machine, with optional patent mono-layer pre- screening module, 2.45mx 1.52m screen. It is used for screening out the fine material before the material enters into the crushing host .C-1540RS a mobile crushing and screening equipment which is used for crushing and screening .C-1540RS increases feedback system and double-layer grading screen on the basis of C-1540. When there is no need recycling or grading materials, we can quickly remove the grading sieve from the device, without any lifting equipment. It is proved that C-1540 tracked mobile cone crushing station has excellent performance in aggregate production and the appliaion of the surface soil of the mine as it has good productivity and high efficiency.

The tower-type asphalt mixing equipment developed by SOUTH provides a thermal efficiency of 90% and an energy reduction of 15%. The equipment uses the unique online intelligent detection. The burner independently developed by SOUTH uses the double frequency conversion, various types of oil, and the original wear-resistant parts imported from Sweden which rank first in the world to provide safe, real-time and fast services.

The tower dry-mix mortar production equipment developed by SOUTH was arranged top-and-down in line with production process. The energy consumption is relatively low and it takes a small floor space. Small cross-contamination of raw materials is generated; the large-size appearance applies to the production of ordinary and special mortar. The dry mortar mixing plant control system developed by SOUTH, which uses the FB series mortar mixing plant for double-machine synchronous control, consists of two computers, high-performance microcomputer controllers, man-machine interfaces, high-speed and high-precision weighing units and international famous low-voltage electrical components.

The main type of tire mobile jaw crushing station developed by ®SOUTH are mobile jaw crushing station and mobile cone crushing station, combined with the solid and reliable jaw crusher host and high-duty vibration grate feeder , which are portable and high-productive primary crushing stations. CSW1175J and CSW1060J can be applied to a wide range such as tough rocks, sand, gravel, mine and regenerated concrete (etc. almost all kinds of material) and its design is contribute to raise your profit. ®SOUTH CSW1300C and CSW1000C tire mobile cone crushing stations are new-type mobile cone crushing stations, which are specially suitable to dealing with high abrasion material. And CSW1300C is a bigger mobile cone crushing station with higher production.

Standing-type dry-mix mixing equipment developed by SOUTH is arranged around the building with simple structure and it is proper to produce rare ordinary mortar. The type of the mortar is in bulk and the structure of which is similar to commercial mixing station. And the investment scale is at middle level.

Stabilized soil mixing equipment developed by NFGL uses professional micro-control system. In performance, it has features such as high material adaptability, grading variety and high reliability. Structurally, it is designed with the concept of compact structure with reasonable layout, largely downsize the floor space. And in operation, it has advantages such as easy to operate, install, adjust and maintain. From the aspects of spare parts, the most proper part with highest-cost performance are picked, saving cost and creating more economic profit. NFGL stabilized soil mixing equipment can be applied to sub-base construction of highway, airport and railway in any level.

Self-compacting Concrete Mobile Mixing Station developed by SOUTH and CARS can be applied to CRTSIII, which is developed specially for China high-speed railway technology. High-compact, flexible and newly-developed mixing host can meet the requirement of new concrete proportion and non-traditional aggregate mixing. The design is humanized and the system of it is intelligent, which will do help for the development of china high-way. The cement used in high-speed railway construction requires fluidity and is flat without pressuring, which requires the mixer of the cement producer is accurate in calculation and measurement as well as measure the water content and temperature according to the weather. YHCN50 self-compacting concrete mobile mixing station developed by SOUTH can totally meet these requirements.

The hydrocyclone separation technology is adopted to eliminate sludge, clay and other impurities of the size less than 75μm and reclaim fine sand of the size larger than 75μm maximally. Meanwhile, the technology can dyhydrate efficiently the materials washed and control the moisture content of finished sand. The technology enjoys good cleanliness, less losses of fine sand and strong processing capability. The appliaions of the equipment: various types of concrete, mortar, asphaltic sand, river sand, lake sand, silica sand for use in the glass industry, golf course sand, bed sand, iron sand, tailings and other recovered materials.

Not all crushers are used in the same appliaions, and therefore we provide various crusher types. ®Canica vertical-shaft impact crushers have durable structures and cheap quick-wear parts, which brings high competitiveness in the market. In addition, these crushers have flexible configurations. Selecting proper configuration is the key to reduce the costs of wear-out parts and the downtime, thereby maximizing the profits. In this regard, we provide various crusher types, such as open-type and close-type rotor, impeller, rock cavity and anvil to meet different production and operation requirements.

The middle-end S3 series dry-type shaping and sand making system developed based on SOUTH's high-end V7 dry-type sand making system uses granite, limestone and other mine rocks as well as gravel tailings as raw materials and has various components, such as the vertical-shaft impact crusher, vibrating screen, dust collection module and transmission module, which makes the green, harmonious, intelligent, and service-oriented complete sand making equipment, thereby realizing clean production and providing important strategic significance for completely replacing the machined sand with the natural sand and accelerating the transformation of economic growth patterns. The S3 series dry-type shaping and sand making system makes breakthroughs in the key vertical shaft crushing technology and integrates the air screen classification function into the main crushing and shaping frame to realize the real technological breakthrough and to produce multiple effects of crushing, shaping, sand making and graduation on the main crusher frame, thereby making the best particle shapes during crushing. In addition, the system uses the double vibration self-synchronous linear vibration screening for centralized dust collection and removal through offline ash removal pulse dust collection to make high-quality finished aggregate and sand, thereby realizing clean production and significantly improving the technological production process compared to the middle-end shaping and sand making equipment developed by China's other manufacturers.

When the old asphalt mixtures planed from aging asphalt pavements using the recycling technology are added at different mixing ratios to the mixers in asphalt mixing plants of various models for stirring after these mixtures are screened, heated, stored and metered, the RLB series asphalt hot recycling equipment evenly mixes these mixtures with the original raw materials in the mixers to produce high-quality asphalt mixtures. The majority of asphalt mixing equipment used in China's pavement engineering is the forced batching plant. The use of other recycling methods means that the existing equipment will be unused or abandoned. In this regard, the best choice is to add the recycling function module to the existing equipment through upgrading and reconstruction, which will expand the equipment's applications, thereby bringing you more benefits. The RLB series asphalt hot recycling equipment developed by SOUTH is the specially designed forced intermittent asphalt mixing plant.

Preform-only Mixing Station (plant) developed by SOUTH can be applied to small-and -medium construction projects, preform plant and commercial concrete producer. The types are: HZS50, HZS75, HZS100 and HZS150. And the biggest productivity reaches 150m3h theoretically.

Powder silo Top Mounted Commercial Concrete Mixing Station developed by SOUTH has advantages such as energy-saving, stability, environment-friendly, energy-saving and intelligence. The type includes HZS180, HZS200 and HZS225. The biggest productivity reaches 225m3h theoretically.

NZGOB burners are the new generation of axial flow oilgas burner developed jointly by China and Europe. These burners use the special burner simulation analysis led by an Italian expert Sartori Giogio and conducted by the European organization for thermal energy technology research, integrate the advanced European technologies, and take advantages of the best burner model patent with the principle of low emissions for environmental protection and calorific value as the core. These burners with excellent and stable quality are highly praised by customers around the world and therefore they can be used as the ideal accessory products for asphalt mixing equipment.

NZGB gas burner is equipped with the atomization control module developed by SOUTH, which can automatically regulate atomization output capacity and keep it, totally solving the problem of the influence the have on pressure fluctuation and realizing the unification of absolute burning and low emission.

The oil supply system of light and heavy oil burners developed by SOUTH uses modular design to integrate the exhaust tank, filter, double-pump group and electric heater as one oil supply module, which provides stable performance, the highest efficiency and the most convenient maintenance, and improves operation efficiency and performance, thereby preventing leakage and pressure loss during site installation.