Metrix Automation India Pvt Ltd. Kukatpally, Hyderabad, Telangana

We are dedicatedly engrossed in presenting a broad spectrum of Wireless Converter. RS485 to wireless converter is the direct replacement to the long length and high maintenance requirements of RS485 bus. It is easy to install thus highly demanded in the market by our valued clients. We are promised to deliver this complete array within stipulated set of time span. Features : Operating frequency 865 MHz 19200 Baudrate on RS485 side Transmit and Receive LED indications on RS485 side and wireless side 12—24V operating voltage In built ESD protection for RS485 bus Signal Strength indication Applications : Wireless Sensor Network Industrial Instrumentation for data communication Wireless Serial RS232 Port Adapter Wireless to RS232 converter is the direct re-placement to the RS232 cable between two instruments Features : Operating frequency 865 MHz Configurable Baud rate from 1200-230400 on RS232 Transmit and Receive LED indications on RS232 side and wireless side 5V or Optional 12—24V operating voltage Signal Strength indication Configuration can be done with the help of X-CTU software and USB to TTL converter cable (Please refer data converter product )

  These clocks are designed to be used in industries or common waiting halls like Airports, Railway Stations, Hospitals etc.It uses 4 digits of six inch seven segment displays with super bright LEDs (each segment is made of 4 pixels with 4 LEDs in every pixel).  Operates either in 12hrs mode or 24hrs mode. Two keys SET and ALT on front panel are to set the time. Provision to set time through PC COM port or any RS232 Port. Can work as master slave to display synchronized time ( Could be synchronised with a GPS receiver ).

Xbee USB modem has a Digi Make XBEE 865 module. It is used to transmit and receive data from computer to the other XBEE 865 modules wireless connect the wireless modules in the field. When drivers are installed in the computer an extra com port is visible through which data can be received and transmitted. Features : Operating Frequency of 865MHz Data rate over the air of 10/80 Kbps FTDI chip based on USB side USB powered and with cable length of 1 meter Data Transmit and Receive Led Indications on both USB side and wireless side Adds Virtual COM port in computer when drivers are installed Signal Strength indications Applications : Wireless Sensor Network Signal testing and Signal Range test in the field

Since our beginning, we have been providing a wide spectrum of high quality USB To TTL Converter to our customers. It is used for connecting USART RX and TX (of Micro controller or any other module) TTL lines directly to the windows/Linux based computers thus avoiding RS232 level converter. It is available in the market at reasonable price range. Features : FTDI Chip based Cable Length 2 meters Available in 2.54mm, 2mm, 1.27mm pitch connectors on TTL Side Inbuilt ESD Protection Transmit and Receive LED indications Adds virtual com port in computer when connected and drivers are installed Can be used directly for Rabbit Micro processors programming and Digi make Zigbee module configurations 

The Clean Room Smart Process Scanner is a 3 Line Smart Process Scanner which accepts 3 Analog Inputs from sensors/transmitters & displays the 3 parameters directly onto the Display. Especially suited to display the clean room parameters of temperature, humidity & differential pressure in a single instrument. Also suited to display the various parameters of Air Velocity, Oxygen, particle count or any other analog input. The Clean Room Smart Process Scanner accepts 3 analog inputs of 4-20mA or 0-10 V.D.C. & displays all 3 parameters simultaneously on the large 1 Inch High Red LED 7 Segment Display. The instrument works on 24 V.D.C. & has an integrated RS485 Modbus Communication for integration to BMS/SCADA/PLC. The enclosure is only 30 mm. deep & has a front stainless steel flush plate mounting , suitable for both modular walls/brick walls. 

Being one of the prominent associations, we have been successful in offering an extensive array of Training Simulator, which is widely praised in the industry for being highly efficient in nature. With the help of experienced engineers incorporating best quality components, materials and technology, this simulator is engineered with utmost accuracy. This simulator is offered to the clients at most reasonable prices. Features : Simple to install Easy operation Highly efficient

Protocol converters, Serial protocol support for Modbus (RTU and ASCII) MasterSlave, Network protocol support for Modbus TCP (ServerClient), Supports Serial to Ethernet Raw conversion with Telnet RFC2217, Isolation between Communication Ports & Input Power supply.

Features : Serial protocol support for Modbus (RTU and ASCII) Master/Slave Network protocol support for Modbus TCP (Server/Client) Supports Serial to Ethernet Raw conversion with Telnet RFC2217 Serial Interface support for RS232, RS422 and RS485 network Serial Baud rate: 300 bps to 115.2 Kbps Ethernet interface support: 10/100Mbps with Auto Negotiation Configurable using Embedded Web server and Application software Network Protocols Supported: ARP, TCP/IP, HTTP, BOOTP, TFTP, ICMP, TELNET (not applicable for Modbus RTU to Modbus TCP Protocol conversion) , DHCP, AutoIP Isolation between Communication Ports & Input Power supply

Humidity transmitters, Humidity and Temperature Transmitter, which are available as per the international quality standards and we offer these products in various specifications to our clients. These products are available to measure the highest Humidity and temperature are suitable for various applications. SHT-75 seniron make Temperature and Humdity Sensor. This module can measure temperature from -20degC to 100degC and Humdity range is 0-100%. Human Interface with graphical Display and keypad for configuration settings.

The Dredger Monitoring Unit(DMU) enables the dredging master to verify and control the position of the cutter or wheel in relation to the channel's center line, the working depth and profile set points.  Position in LATITUDE, LONGITUDE and ALTITUDE Present Depth of Cutter Width of cutter from CENTER LINE The DMU is an independent system but can also be incorporated into larger systems – usually as a signal source for the automation of the dredging process, such as the automatic cutter or wheel controller. Has provision to integrate more Dredger Parameters like Pressure, Voltage, Vacuum etc. making a total Dredger Supervisory Unit. Components of DMU :There are 3 major components in DMU  DIGITAL PROCESSING UNIT(DPU) unit with 5 inch Monocrome display and inbuilt GPS. INCLINOMETER sensor connected to Processor Unit used to measure the Depth of the cutter. Tilt Compensated Magnetometer measures the HEADING value of the Dredger. DPU processes signals received from Inclinometer and Heading sensor and calculates the Depth and Width of cutter for given Dredger Parameters and Also Displays the present Location Latitude and Longitude by using GPS. 

Differential pressure transmitters, We supply quality range of Differential Pressure Transmitter which employs the latest technology to be at par with the latest requirement of the clients. The Differential Pressure Transmitter offered by us provides virtually the high level of performance and precision in the market. These are equipped with the turn system with wall-mount plate for quick and easy mounting.

We supply quality range of Differential Pressure Transmitter which employs the latest technology to be at par with the latest requirement of the clients. The Differential Pressure Transmitter offered by us provides virtually the high level of performance and precision in the market. These are equipped with the turn system with wall-mount plate for quick and easy mounting. Specifications : Measuring ranges from 0/ 10000 Pa to -1000/ 2000 mbar (according to model, see Configuration Configurable intermediary and central zero ranges 0-10 V or 4-20 mA output, active sensor, power supply 24 Vac/Vdc (3-4 wires) or 4-20 mA output, passive loop, power supply 18 to 30 Vdc (2 wires) ABS IP 65 housing, with or without display

This product is specifically designed for Indian Army for Tracking the radio sets. CDSS stands for Combat Decision supporting system. This has got inbuilt GPS and is used to transmit the location data through STARSV MKII, CNR and HX radio sets which are carried by Radio men for communicating. A PC installed with the SIT AWARENESS SYSTEM Software and connected to STARS V MK II/CNR/HX Radiosets will receive the location data from all the CDSS modules and displayed on the maps. Features : GPS ACCURACY UP TO 3 mts. Memory up to 1,63,000 records i.e we can have data stored continuously for one month. Voltage supply 9V—24V. Compatible with STARSV MK II, CNR and Hx Radio sets. Current Consumption < 80 mA Stand alone software in base station for tacking. Rugged Enclosure with display and key pad.