Steam Tech Engineering Habsiguda, Hyderabad, Telangana

The enthalpy in the steam basically has two components : The Latent heat and the Sensible heat. Whereas condensate has only sensible heat. This condensate has to be removed as soon as it is formed, because it hinders to efficient heat transfer as well as leads to water hammer phenomenon as it is hot water (having more Specific Gravity) that moves with high velocity of steam (8 to 10 times higher than water), carrying enough momentum to rupture pipes and which is damaging to the plant pipelines as well as piping equipments. Hence, need to remove condensate from steam main and trap steam. This is done by steam trap.The thermodynamic traps separate condensate and steam based on velocity which in case of steam is higher than that of condensate. These are used mainly on drip lines of the main steam distribution line, platen presses and super heated steam lines to remove condensate.Condensate pressure is used to open the trap by lifting the disc, discharging condensate in low pressure. Due to low pressure flashing of condensate takes place. High flash steam velocity (approximately 5 times of condensate) creates a low pressure zone below the disc. Accumulated flash steam force over the disc becomes greater than the incoming condensate pressure this leads to closure of the disc. Subsequently the flash steam condenses and the incoming higher pressure condensate pushes the disc opening the trap and thus the cycle continues. The UTD 120 is a steam trap with integral strainer specifically designed to meet above application.UTD 120 is a Thermodynamic Steam Trap manufactured in forged Alloy Steel construction. It is a very rugged design built for high pressure applications such as in power plants. Also used for superheated applications.

Brand Name : Uni Klinger

UNI KL/NGER LIMITED is offering a full range at Spiral Wound Gaskets. The primary objective is to make available in tndia, Spiral Wound Gaskets manufactured to the most exacting international standards such as API 601, ASME B1620, ASME B16.4 7 A & B series, DIN, British Standards, JIS standards and others as specifiedSuperior quality of UKL Spiral Wound Gaskets meeting international standards, is achieved by means of imported computer controlled winding machines, which ensure total repeatability in such criticalareas as: Winding profile Tension ol winding Winding pressure Number of primary, secondary and tertiary windings Number of weld points Weld penetration All of these factors are vital for control of manufacturing spiral wound gaskets for criticalservice applications.The design principle of UKL Spiral Wound Gaskets : The basic sealing component of every Spiral Wound Gasket is the wound element. The unique profiled metal strip is spirally wound to integrate with the specified sealing element material. To improve the mechanical strength and other sealing characteristics and to comply with international standard, some layers at the beginning and at the end are wound without soft material and spot-welded over the total circumference. Consistency of winding tension combined with the profile of the winding, provide for a superiorsealing performance. This advantage is achieved by special process of feeding preformedmetal strip and soitflller material This gives the gasket, the required recovery properties at designed bolt load, even at fluctuating operating conditions. UKL Spiral Wound Gaskets are now available as sealing elements and also with inner andi or outerrings. A major requirement of any gasket is its ability to recover and maintain a constantsealing force under variable loads. The effect of pressure and temperature fluctuations, together with radial forces, stress relaxation and creep, demand a gasket with adequate flexibility and recovery to maintain a seal even under trying conditions. UKL Spiral Wound Gaskets can meet this reguirementadeguately.

Size : 15mm To 500mm

Material : CS/SS 304 /SS 316/SS316L

Shape : Standard Class 150# And 300#

Thickness : Sealing Element Thickness 4.5mm

Brand Name : Uni Klinger

THE PISTON VALVE principle is a KLINGER idea. One of many ideas which has achieved world-wide recognition. Continuously modified and matched to modern requirement, the piston Valve has provided itself by the millions throughout the world. Today we can say with pride that our group is worlds largest manufacturer of valves, based on this design principle. KLINGER Piston valve performance is backed by central R & D of KLINGER at Switzerland.The shut off assembly comprises of a stainless steel piston, two resilient valve rings and a ferrous metal lantern bush. The sealing consists of the cylindrical surface of the piston and the corresponding inner surface area of the sealing rings. This provides a very large sealing compared with globe valves with conventional design- one of the reasons for the Piston valve’s excellent seal.The valve Rings are the heart of the piston valve. They are made from KXGT, a material specially developed and exclusively used for the manufacture of valve ring. KXGT consists essentially of asbestos, a high quality elastomer and graphite. KLINGER valve rings are not merely surface graphited; the graphite content extends throughout the ring. For this reason its outstanding self lubricating properties are retained throughout the rings entire service life. KLINGER valve rings are resilient, accurately dimensioned and in consequence of their good recovery characteristics have excellent form retention and long service life. KLINGER valve rings are resistant to water, steam, oils, solvents and wide range of other media. KLINGER valve rings can be used for more than 230 listed fluid media.Features  : Seatless and Gland less valve. Economic, easy to service. No erosion of sealing surface. Maintenance free. Compensation for thermal expansion with use of Belleville washer. Leak-tight across ports and to atmosphere. On Request : IBR/Non-IBR MOC : Cast Stainless / Alloy Steel Valve with extended spindle. Valve with Heating Jacket Pneumatic / Electrical Actuator Installation :Preferred direction is as per arrow, however this valve is a Bi Directional Valve. This valve can be installed in any position without any adverse effect on performance, seal ability or flow.Due to soft sealing principle it is advisable to install a strainer upstream of the valve to avoid damage to the rings caused by weld slag, metal and other solid impurities.

Brand Name : Uni Klinger

Thickness : 3mm-25mm

Color : Black, White, Yellow, etc.

Brand Name : Uni Klinger Ltd

Size : 3mm-25mm

Size : 10-20inch, 20-30inch, 30-40inch

Material : Asbestos

Thickness : 0-5mm

Feature : Durable, High Strength, Perfect Shape, Strong Construction, Superior Finish

Brand Name : Uni Klinger

Shape : Flat Gasket

Details : UKL ceramic packing is reinforced with e-glass fibre to withstand higher temperatures. This packing is suitable for steam boilers, coke ovens & high temperature valves for air, flue gas.

Brand Name : Uni Klinger

Material : Metallic And Non Metallic

Shape : Sheet

Thickness : 0.5mm To 5mm

Size : 1500 X 2000 Mm

Brand Name : Uni Klinger Ltd

The enthalpy in the steam basically has two components : The Latent heat and the Sensible heat. Whereas condensate has only sensible heat. This condensate has to be removed as soon as it is formed, because it hinders to efficient heat transfer as well as leads to water hammer phenomenon as it is hot water (having more Specific Gravity) that moves with high velocity of steam (8 to 10 times higher than water), carrying enough momentum to rupture pipes and which is damaging to the plant pipelines as well as piping equipments. Hence, need to remove condensate from steam main and trap steam. This is done by steam trap.UKL Ball Float Trap discharge condensate near to steam saturation temperature, which works on the principle of Buoyancy, [densities difference of Water and Steam].The rising condensate level elevates the Float open the valve and discharges the condensate. When the level of condensate drops, the float falls down and the valve close the trap.It is commonly used for most process heating applications. Wherever steam is used for indirect heating application, the trap to be used must be of mechanical design. It is a continuous discharge type steam trap. This trap can handle very high condensate loads and the discharge will be proportional to the differential pressure across the trap. There may be other similar process applications where the heat load is small and a mechanical trap can handle small as well as fluctuating loads.This trap is provided with two optional features called Steam Lock release (SLR) and Thermostatic Vent (TV). The SLR is a manual operation to release steam that may hamper free movement of the float on water level. The TV will ensure that air and such un dissolved gases will be automatically vented out when present in condensate.

Type : Steam Traps

Pressure : High

Material : Stainless Steel