Coin Battery Holder
Get Price Quote
We are highly acclaimed in the market for offering a striking range of Coin Battery Holder at budget friendly rates. We value our clients, and promise extraordinary fine quality products, and our range of products is acknowledged among our patrons for its anti-corrosive nature and majestic shine. We offer a wide range of holders in different sizes. Before supplying the product, we thoroughly check it as per the quality assurance tests to ascertain its quality and durability. We are located in Delhi, India.
Swagelok Type Coin Cell Holder
4,500 Per Piece
1 Piece (MOQ)
Best Deals from Battery Holder
AA 1 cell battery holder hard plastic case with wire 1 (1 x 1.5V = 1.5Volt)
23 Per piece
100 Piece (MOQ)
4aa battery holder
699 - 799 Per Bag
25 Piece (MOQ)
US make
ABS Plastic Battery Holder
10 Per Piece
Plastic Black Battery Holder
4 Per Piece
1000 Piece (MOQ)
Cell Holder
Get Price Quote
An excellent addition to any electricity lab, this newly designed cell holder fixed on a beautiful blue plastic moulded base fits four D-cell batteries connected in series. • Base is clearly engraved with DC 1.5, 3, 4.5 & 6 V. • Works as low voltage power supply
Battery Protector
600 Per Piece
16) MOTORMAN BATTERY MASK Inhibits sulphonation, Better contact efficiency & longer life of battery. ADVANTAGES : • Provides protective mask to Battery terminals which inhibits corrosion due to battery acid fumes, Sulphonation, attack by moisture and weathering effect. • Improves contact efficiency. • Enhances battery life. METHOD : • Shake can well before use. • Thoroughly clean the battery terminal and spray evenly to thin coat on it. PACK SIZES : • 300gm : suitable for individual customers as well as garages and industry.
Battery Holder
130 Per Piece
We are the main supplier of this product.
Battery Holder
Get Price Quote
ABBOMEDTM Battery Holder stackable accommodate upto 1.5V, held in spring clips 4 mm. sockets for 1.5, 3, 4.5, 6, 0 Volt tappings. Supplied without battery.
Cell Holder
Get Price Quote
We are highly prized in the market for delivering a broad range of Cell Holder at market cost. Being one of the chief manufacturers and exporters, the product, supplied by us, is available in perfect dimensions. We carefully manufacture this product to ensure optimum performance, high strength, and low maintenance cost. We are based in Ambala, Haryana, India. More about of Cell Holder : An excellent addition to any electricity lab, this newly designed cell holder fixed on the beautiful blue stable plastic moulded base fits four D - Cell batteries connected in series. Base is clearly engraved with DC l.5, 3, 4.5 & 6V. Works as low voltage power supply. Model Number : GP-907
Cell Holder
Get Price Quote
Plastic moulded holder with brilliant finishing to hold cell of 1.5 volt, big size. Individual units can be joined in a tandem to make a battery of required voltage. Sockets of 4mm are provided on the cell holder.
Battery Holder
Get Price Quote
The 4X AA Battery Holder puts a nice finishing touch on your battery powered project. It can provide about 6V(4x1.5V) Voltage power for your project. You can use AA-sized Alkaline or Rechargeable batteries with it. Batteries are not included.
battery holders
Get Price Quote
Battery Protector
Get Price Quote
Each time a battery is discharged some of the sulfuric acid in the electrolyte is converted to lead sulfate crystals which form on the plates. These crystals interfere with the chemical rea -ction necessary for proper battery operation. When the battery is recharged MOST (but not all) the sulfates are reconverted back into sul -furic acid. This is why a discharged battery will have a low Specific Gravity (SG) reading. Over time the sulfates which are not reconstit -uted as acid form stubborn patches of large crystal growths that will grow and eventually choke the life out of a lead acid battery. These crystal growths if not stopped will act like ice expanding the cases (bulges), breaking the plates and plate and cell interconnects and causing shorts. The usual practice in maintaining a battery in good condition is to apply a periodic equalization charge over and above what would be a normal full charge. Unfortunately, this is an energy wasting tactic. It ultimately results in clean battery plates, but at a steep price, especially if the energy must come from a generator.If badly sulfated batte -ries are treated, it is convenient to use a trickle charger of one or two amps.In this case, the simplest way to see that the circuit is havin -g an effect is to note that the terminal voltage actually drops each day as the batteries slowly charge. This is a result of the internal resistance of the cells decreasing as the plates become slowly cleared of the sulfate,and more useful plate area comes in contact with the electrolyte. Also,the specific gravity of the cells begins to rise slowly, evidence that the sulfate is going back into solution.To further check the progress you could do a discharge test, using a known load, to determine the useful capacity. This would involve measuring the length of time taken by the load to drop the battery voltage from a high level to a low level. If you repeat this test, a gradual lengthening of this interval should be noted.
Battery Holder
37 Per Piece
Cell Holder
10 Per Piece
100 Piece (MOQ)
Battery Holder
Get Price Quote
Battery Holder
255 Per Piece
battery holders
Get Price Quote
Arbin provides batteries for all dimensions of batteries including coin cell, flat cell and cylindrical cell batteries as well as high current battery holders for flat cell and cylindrical cell batteries.