Microprocessor Development Board Dealers

• Frequency: 2 KHz to 20KHz
• Load Range: 1/2/3/5/10 KW
• AC Ammeter Range: 0-5/10/15/25AAC
• Voltmeter Range: 0-300/500V
• Material: Electronics

We are well-known Exporter and Supplier of Laboratory Board (MDSP2812). VPL-MDSP2812 is a powerful TMS320F2812 based DSP development board which enables the user to control 3 Phase AC Motor, Single Phase AC Motor & DC Motor. Features DSP processor TMS320F2812, 32-bit fixed-point high-speed digital processor, the highest frequency of 150 M Built-in 128 K * 16-bit FLASH, users can be stored procedures, FLASH can be encrypted. Built-in 18 K * 16-bit SRAM Extended 256 K * 16-bit SRAM (basic configuration), which can be expanded to 512 K * 16K. Expanded 4 MB FLASH (basic configuration), which can be expanded to 8 MB, user-friendly prototype development. RTL8019AS network interface chips, realization of Ethernet communications. TLV320AIC23 audio codecs, recording and radio to achieve. HOST USB interface chip SL811H, plug-ins to mass storage devices. RS232 communication with PC. RS485, CAN2.0 conversion circuits, user-friendly network. LCD interface Four keys, LCD display for man-machine communication Provides up to five of the road widening may be shielding interrupt source inputs Provide as many as two-way, expanding the non-shielding interrupt source inputs Provides up to 8 input, 8-output interface Provides bus open, data lines, address line, the Line of Control, the special features pin all the leads, User-friendly secondary development. Alteras latest MAX-II CPLD (EPM240), so that users in the study of the palm DSP Use of second-generation CPLD Three Phase AC Motor Control FRC connectors are provided to interface with the FPGA / Microcontroller/DSP/ARMX Controllers Power Input/Output lines are terminated at banana sockets. Built - in over voltage, under voltage, over current & over Temperature protection. Power module is designed for Motor control applications upto 3 HP by using the 3rd generation of IGBT & DIODE Technology 1200V/25A converter bridge for AC-DC power conversion with filter capacitor. 4 Nos. of Hall Effect current sensors provided for DC link current and 3 output current measurement. All the PWM signals are isolated using opto isolator. Protector circuit for over current with LED induction Independent power supplies for all isolated circuits. Voltmeter to indicate the DC link voltage. All current sonsor O/Ps, PWMS are terminated at front panel.1200V/25A converter bridge for AC-DC power conversion with filter capacitor. 4 Nos. of Hall Effect current sensors provided for DC link current and 3 output current measurement. All the PWM signals are isolated using opto isolator. Protector circuit for over current with LED induction Independent power supplies for all isolated circuits. Voltmeter to indicate the DC link voltage. All current sonsor O/Ps, PWMS are terminated at front panel. Single Phase AC Motor Control This module can be interfaced with IGBT module. The following experiments can be done using this firing module and device module combination. Four no. gate signal to trigger four IGBT/MOSFET. IC based carrier (triangular) wave generation with variable frequency (2 KHz to 20KHz) IC based reference sine/square/trapezoidal wave generation with variable amplitude & frequency. One no. rotary switch to select different type of reference waves. Two no. potentiometer used to wary the frequency amplitude of reference signal. Comparator circuit, it compares carrier and reference wave One no. rotary switch to select PWM for different types of modulation sine/trapezoidal/square. All four PWM outputs are terminated on the front panel for device module 220V AC input, +15V DC for control circuits DC Motor Control FRC connectors are provided to interface with the FPGA / Microcontroller/DSP/ARMX Controllers Built - in over voltage & over current protection. Power module is designed for Motor control applications upto 1 HP. SCR based design with pulse transformer for triggering of SCR. All the PWM signals are isolated using opto isolator. Protector circuit for over current with LED induction Independent power supplies for all isolated circuits. Voltmeter to indicate the DC link voltage. All current sonsor O/Ps, PWMS are terminated at front panel.

• Type: Drawing Boards
• Material: Wood
• Shape: Rectangular
• Style: Standing
• Application: Laboratory
• Finishing: Polished
• Size: 12x18 Inch

• Type: Physics Lab Equipment
• Material: High quality
• Condition: New
• Country of Origin: India
• Brand Name: RX2
• Application: Educational use
• Brand Name: RX2 Scitech India
• Name: friction board
• Usage: Educational use
• MOQ: 1