Om Engineering Co. Vaishali Nagar, Jaipur, Rajasthan

The safe working load per single part of rope is approximately one sixth of the nominal breaking load of ropes as 2 2 specified in B.S.302 621 in the 6 x 37 group of tensile strength 100110 ton inch (160175 kgfmm ). This is the nominal breaking load on which the design of blocks to this standard is based. Multiple sheave block with safe working load over 20 tons up to and including 40 tons.

For lifting and transporting single steel plate. Capacity range : 1-16 tons The vertical steel plate lifting clamp can be used solely or in pairs Multi plates must not be lifted. Avoid snatch or shock loading Up the locklever to tighten lockspring when it is under loading. Down the locklever to loose lockspring, then unload.

Semi Automatic Grinder efficient for improving drill steel rod life & drill machine speed  

A new concept in Marble Drilling, Metal Mines, Tunnels, Dam & Shaft Sinking etc.New Model, One Touch Operation, Few Parts, Low Maintenance Heavy & Long Chuck Nut, Double Sided Pawls & Steel Rifle Nut Newly Designed, Foot Rest for easy & Effective Drilling Low Air Pressure & Low Air Consumption.

For underground mines, shaft sinking & tunnels.4000 RPMDischarge 2000 CFM at 200 meter length with 100 mm w.g.Working at 70 - 80 psi &100 cfm air consumption

For lifting and transporting single steel plate. Capacity Range : 2-10 tons. The working load limit is the maximum load that the clamps are authorized to support when used in pairs with a lift angle 60 deg. In lifting operation, four clamps must always be used. When the steel plate is too long, use an equalizing beam to prevent overloading the clamps. 2 times WLL - Proof load, 4 times WLL - minimum breaking point.

  Drop Forged, Quenched and Tempered with Alloy Pins   Maximum Proof Working Load is 2.2 times the working load limit   Minimum Breaking Load is 6 times of working load limit   Working Load Limit permanently   Forged - Quenched and Tempered, with alloy pins   Capacities 1/3 thru 300 tons

Button Bits are available in different sizes ranging from 3" to 14" to suit different applications. Button Bits designs have been perfected from the most extensive rock drilling experience. DTH Hammers are available in different sizes ranging from 3" to 8" to drill in different rock structures. They are designed to give peak performance, easy penetration even in the hardest rock conditions.

The  Drifter is Designed for Long Hole drilling in underground mines, grouting hole for surface mining and construction applications as well as for drifting and tunneling.Drifter features a 120 MM piston diameter and a powerful impact and rotation mechanism.It is used with 1¼" & 1½" rope thread extension drill steels rods.The rotation mechanism can also be disengaged & the impact action used to rattle a tight joint or a jammed bit.

KDP - 250 & 170For Shaft sinking, Drives, Decline, Ramps, Tunnels & Dams etc. KDP - 250Head - 50 - 70 Mtrs.Working Pressure - 70 - 80 psi and 100 cfm Consumption.Discharge - 250 Lpm KDP - 170Head - 40 Mtrs.Working Pressure - 60 - 70 psi and 70 cfm ConsumptionDischarge - 150 Lpm

A versatile Machine for High Production Bar-Cutting, where in the Operating Height is at Eye level, features an Automatic Bar-Clamping arrangement.  

Heavy Duty use for all Industrial Applications Grade 80 Alloy Steel Load Chain for strength and wear resistance Minimum maintenance for reduced downtime Safety factors is 4 times SWL 1 year warranty against manufactured defects Needle roller bearings for high operational efficiency Compact in size and light in weight for easy handling

Roof Bolting & Cable Grouting Fully Grouted Bolts & anchors installed by pregrouting or post injection. Long hole grouting from 3m to 20m, can be injected with cementations or other mixer (Water based resins etc.) in ratio from 1 : 0.00 up to 1 : 2. Ventilation control by spraying on to walls and prefabricated meshes. Injection of Grouts - set props with a modification to produce high pressure setting up to 500 PSI.

A Compact and Light weight Bar-Bending Machine wherein the Operating Height is at comfortable level. The machine is designed to Operate in either directions CW or CCW Bending. Set the desired angle and the machine will execute accurate bends. The maximum bend allowed is 180 deg, U-bend.  

shaft sinking & tunnels Working pressure - 50-70 psi & 70-80 cfm air consumptionDischarge -20 feet (6mtrs.)