Polyurethane Coatings Dealers in Kanpur

We are leading supplier, trader, wholesaler and distributor of melamine sealer. These products are sourced from reliable vendors of the industry, ensuring durability at customer end. Moreover, this product can be used for wooden furniture, musical instruments, wooden walls of executive chamber, wooden room separates, kitchen wooden shelf etc. In addition, we offer this range of melamine sealer at market leading prices.

ShaliUrethane FCM 2001 E is a two component Solvent Free Polyurethane Coat that has excellent mechanical properties, Impact Resistance and helps prevents Cracking. Solvent Free Polyurethane Coating is a solvent less formulation and can be applied at varying film thicknesses with in the same application as required by differing service demands or surface conditions. With our Solvent Free Polyurethane Coating, the degree of protection is no longer limited to the maximum build of multiple coats of solvented coatings. Solvent Free Polyurethane Coating meets all known VOC regulations and is virtually odorless during and after application. Solvent Free Polyurethane Coating eliminates creation of pinholes due to solvent evaporation, producing a dense monolithic membrane. The coating is sufficiently elastic to withstand normal shrinkage cracks in concrete without breaking. An ideal immersion lining, it is abrasion-resistant, chemical resistant, and highly impermeable and can be placed in service within moments after application. Two Component Solvent Free Polyurethane Coating : About the Product : SHALIURETHANE FCM 2001E is a Two Component Solvent Free Polyurethane Coat that has excellent Mechanical Properties, prevents Cracking and has excellent Impact Resistance.Shaliurethane 2001 E : is a solvent less formulation and can be applied at varying film thicknesses with in the same application as required by differing service demands or surface conditions. The degree of protection is no longer limited to the maximum build of multiple coats of solvented coatings..ShaliUrethane FCM 2001E : meets all known VOC regulations and is virtually odorless during and after application. It eliminates creation of pinholes due to solvent evaporation, producing a dense monolithic membrane. The coating is sufficiently elastic to withstand normal shrinkage cracks in concrete without breaking. An ideal immersion lining, it is abrasion-resistant, chemical resistant, highly impermeable and can be placed in service within moments after application. Uses : As a high build coating with excellent water impermeability and improved mechanical properties. Ideal coating for Steel and Concrete Substrates. Pipelines Advantages : Good FlexibilityHigh Mechanical strength High Impermeability Application : Spray Application Equipment Shaliurethane FCM 2001E is typically applied by a Plural ComponentAirless Spray Machine. Recommended equipment is a Graco Airless Spray machine with a fluid to air ratio of at least 45:1 with a variable electronic proportion set to a 3 resin: 1 hardener ratio.Standard equipment typically includes heated hoses, drum heaters, suction feed from 200 liters steel drums (feed pumps not required in most cases), re-circulation system, Gun with spray tips ranging from 0.021� to 0.035�, stroke counter and automatic high-pressure shut-off system. Other set-ups may be necessary and many options are available. Applicator training is required and spray equipment must bottom on a 3A:1B, volume ratio..Other set-ups may be necessary and many options are available.Applicator training is required and spray equipment must be approved by STP-KIPOL Technical Service. Surface Preparation : Concrete : For new concrete allow 28 days cure. De-contaminateas per ASTM D-4258, then abrasive blast clean per ASTM D4259 to produce surface profile resembling coarse sandpaper. Eliminate leaks and infiltrations and remove standing water. Resurface areas with excessive cavities (bug-holes) or exposed aggregates using a highstrength, rapid cure, zero-shrinkage resurfacing product. Wherever possible, fiberglass screen or geo textile fabric may be embedded within coating to �bridge�, rather than resurface cavities, thereby eliminating resurfacing compounds. Apply nominal 5 mils (125μ) Polyhybrid 670-S Epoxy Primer, before top coating the concrete which may be damp to the touch, however, surfaces must be free of condensation and visible moisture. Vacuum the surface to dust-free condition before priming.Carbon Steel : For direct-to-metal application, decontaminate surface per SSPC SP-1 �Solvent Cleaning� if needed, then abrasive blast clean per SSPC SP-10 �Near-White Condition� to produce nominal 31/2 mil (88μ) surface profile. Remove flash rust per SSPC SP- 7 �Brush-Off Blast Cleaning�. Substrate must be dry and dust free before coating. Application to wet surfaces is not recommended.