Water Heater Dealers in Vellimalai, Kanyakumari

Electric calorifiers are one of the easiest method of generating hot water for both domestic and industrial applications. Electric calorifiers are installed in hospitals, hotels, Sports Centres and General Residential Buildings.StandardsASME Code construction:- All tanks are constructed in accordance with ASME code section IV Stamped and labeled for 125 PSI (8.6 BAR) as Standard. Precision also design electric calorifiers as per British Standard BS 853:1996, BS 5500:1997 or in accordance with Art 3.3 of the European Directive EEC/97/23 for pressure equipment.Advantages : Efficiency is maintained throughout the range of load. Even at part load all energy is converted into heat Space requirements are minimum Separate boiler fuel storage tanks are not required Installation is simplified The calorifier can be installed directly with the power supply Maintenance is kept to a minimum. Electric calorifiers are clean Electric calorifiers are extremely quiet Precision CoatPrecision coat is a polymerized coating which is applied to all internal surfaces of the tank. Tank surfaces are first sandblasted and cleaned to a white metal finish and then precision coat is applied uniformly. The tanks are then forced cured at 95°C to form a glossy lining unaffected by thermal shock from -6°C to 80°C. Precision coat is approved by US department of agriculture and with NSF/61 certification for drinking water.Standard – ShellsSteel SA516 Gr-70Coating FDA approved Precision coat materialHeating Element ( Howden UK)Heaters can be designed to operate in 3-phase, 415 volts, 50 HZ / 60 HZ supply. Precision uses two types of commonly used heating elements namely replaceable element and removable core element.Replaceable TypeThe elements on this type of immersion heater can be changed only after draining contents in the water heater.Removable Core TypeFailed elements can be changed without draining the calorifier or removing the immersion heater from the shell. This saves time in changing the defective elements and with less down time. By this we can save the heated water without draining it.MaterialsHeating elements are available in copper, incoloy or Incoloy 825 which are suitable for any water conditions.

Direct Oil / Gas Fired water heaters are the best solution where fuel fired hot water system can be used. Wide range output can be achieved in this water heaters. Fully automatic burners are used for safe operation. Advantages Efficiency is maintained throughout the range of load.Even at part load all energy is converted into heat. Space requirements are minimum. Separate boiler not required. Installation is simplified. The calorifier can be installed with minimum electric load. Maintenance is kept to a minimum. Low nox burners are used. Fuel efficient burners are used. Diesel oil, Natural Gas, LPG and Propane can be used. Can also be used with solar or heat pump system where oil or gas fired system can be considered as a backup. Water heaters are fitted with removable type fire tube heat exchanger. These heat exchangers are made of carbon steel tubes and coated with specially formulated coating material to withstand high temperature. Burner Mono block pressure jet fully automatic oil / gas fired burners are used to heat the water. Depend on recovery, burners can be selected either on / off type or full modulation type. Burners will be highlyfuel efficient and with low nox capabilities. Gas Fired Burner Energy Saving and compatible with environmental requirements Quiet in operation and designed for easy maintenance Designed and approvaed in accordance with the European Standard EN676 Plug – in contact facilities the installation Hinged flange Designed for one stage, two stage, or modulating operation Available for natural gas, LPG, town gas, biogas . Oil Fired Burner Energy Saving and compatible with environmental requirements Quiet in operation and designed for easy maintenance Reliable and trouble – free Designed and approved in accordance with the European Standard EN267 Suitable for high resistance boilers Industry standard components easily available Designed for on / off and high/low operation Plug-in contact facilities the installation With hydraulic air adjustment Fuel – Light distllate oil Class D (1.5-5.5 cSt@40°C)

Electric calorifiers are one of the easiest method of generating hot water for both domestic and industrial applications. Electric calorifiers are installed in hospitals, hotels, Sports Centres and General Residential Buildings.