Electronic Test Instruments Dealers in Kolhapur

• Brand Name: Finder, Acme, Fuji etc
• Application: textile, printing, Food
• Model Number: as per requirements

We can supply Signal Isolators, DC Dc Convertors, Panel Accessories such as Fans, Filters, Thermostats, climate control units, Relay Modules , Cable and cable accessories

ARUN’ Portable Rockwell Hardness Tester is developed to meet the demands of a light weight                        instrument which can be used to carry out tests by a universally recognized method of Hardness                    testing.     Rockwell Method :     This hardness tester can be used in variety of applications and is readialy adjustable to a wide range of          sizes and shapes which are difficult to test in a standard table model hardness tester.    The machine is designed for carrying out Rockwell tests comparable to table model hardness tester             because, the basic things, such as shape of penetrator, method of penetration measurement and loads       are same in both systems.    The photograph on the back side gives the general arrangement of the hardness tester.   The system carries a weight bar (8) pivoted at central point. When the load is applied by the loading               screw (9), at one end of this weigh bar, it deflected and the other end of this bar carrying penetrator forces down into the test specimen.This deflection of weight bar which is proportional to the applied load is indicated on the loading dial indicator (1). Besides this loading dial indicator, there is one penetration measuring  indicator (14) which measures the actual penetration of the penterator into the test specimen is read directly on this indicator. The frame carries two adjusting screws and gear train. By rotating the knurled knob the distance between the penetrator and the support-anvil can be adjusted. 1) Upper Camp2) Lower Clamp3) Support Anvil4) Adjusting Screws5) Knurled Knob6) Penetrator7) Penetrator tightening screw8) Weight Bar9) Loading Screw10) Handle11) Loading Dial Indicator12) Indocator Seat Support13) Indicator Seat14) Penetration measuring indicator Method of Test : 1) Select proper penetrator (6) depending upon the material to be tested.2) Take precaution so thet the penetrator does not project beyond the Upper clamp (1). For this, the loading screw (9) should be sufficiently taken back.3) Place the test specimen securely on suitable anvil (3).4) Clamp test specimen firmly between upper clamp (1) and support anvil (3) by rotating the knurled knob (5) on the lower clamp (2).DO NOT APPLY EXTRA PRESSURE.5) CHECK ZERO SETTING LOAD INDICATOR (11). Rotate bezel to bring pointer over small black dot for zero load..6) Apply 10 kgf (98.07 N). major load by rotating the load screw (9) in clockwise direction such that the pointer on the load indentor (11) comes on set position.7) Check zero setting of penetrator indicator (14). Rotate bezel to bring pointer to ‘O’ on the black scale.8) For ‘C’ scale use diamond penetrator against load of 150 kgf (1471 N) and for ‘A’ scale use same diamond penetrator against a load of 60 kgf (588.4 N).For ‘B’ scale use 1/16 ball penetrator against a load of 100 kgf (980.7 N).9) Take off major load by turning the loading screw in anticlockwise direction, such that only minor load of 10 kgf. (98.07) remains in action –(pointer back to ‘set’ position).10) Hardness value in Rockwell scale is directly indicated on the penetrator indicator (14).Read of number on black scale is diamond penetrator.Read off number on red scale is ball penetrator11) Release load completely by taking back the loading screw (9).12) Turn the knurled knob (5) in anticlockwise direction to loosen clamp and thus the test speciman. Maximum test height 110 mmThroat capacity 55 mm 1) Flat Anvil 1 No.2) ‘V’ Anvil 1 No.3) Test Blocks 2 Nos.4) Diamond Penetrator 1 No.5) 1/16″ Ball penetrator 1 No.

In order to keep the quality of the products up to the mark, we check the entire range against varied quality parameters. Now purchase Clamp Meter at highly affordable prices from us. We are its well-known supplier in the country.

• Brand Name: Motwane
• Model Number: LR 201
• Voltage: 9 V
• Battery Life: 6 Month

'DT' Portable Rockwell Hardness Tester is developed to meet the demands of a light weight instrument which can be used to carry out tests by a universally recognised method of Hardness testing. The machine is designed for carrying out Rockwell tests comparable to table model hardness tester because, the basic things, such as shape of penetrator, method of penetration, measurement and loads are same in both systems.

K3MA-F - Frequency Rate Meter. Intelligent digital panel meter with contact, NPN, PNP or voltage pulse input. Highly visible backlit LCD with programmable display colors. K3MA-J - Process Meter. Intelligent digital panel meter with multi range of DC voltage current input. Highly visible backlit LCD with programmable display colors.

• Application: Industrial / Commercial Metering,Three Phase Metering for HT Consumers,Small Industries ,Foundry ,Engineering Units, Textile ,Hospitals, Other Industries
• Three  Phase metering  purpose: Three
• L & T  ER 300P: Three Phase meter
• 4 quadrant measurement of kWh, kVArh, and kVAh: LCD
• Mainly for Solar consumers: 0.2s
• 5 Amp & 1 Amp: MSEDCL and all Electricity major boards, H T Consumer Metering
• Features : Class 0.2s as per relevant IS and IEC Standards,3 Phase 4 Wire,4 Quadrant Measurement,(Interval Data) features,Optical port,RS 232 / RS 485 / IR / IrDA / RF (2.4 GHz/865 867 MHz) (optional)

Panel Meter, Printed Circuit Boards, Embedded Projects Services

PVC, Sandal

clamp meters

Digital Energy Meter

Single Phase Prepaid Meter

Flow Meter

Amprobe Solar Power Meter, UVC Solar Meter, Commercial Solar Net Metering

Energy Meter, Active Components, Sensors, Super Capacitor, Rf Transmitter

Ammeter, Laboratory Instruments, Galvanometer, Industrial Automation

Energy Meters, Transformers, Automation Solution