Sidharatha Equipments GIDC, Mahesana, Gujarat

  We are Manufacturer of Wet Mix Macadam Plant Since 1991. and We are exporters of Wet Mix Macadam Plant, leading Supplier of Wet Mix Macadam Plants in India PUG MILL A twin shaft pug mill mounted on antifriction bearing provides quick, continuous and homogeneous mix of aggregates and additives. FOUR-BIN FEEDER It is of single chassis construction. At each Bin a radial gate is provided which can be opened in any position to regulate the aggregate flow. Individual endless belts are provided, below the gates to discharge material onto the gathering belt.   SLINGER CONVEYOR An inclined conveyor with 600 mm wide belt mounted on idlers receives aggregate from the gathering conveyor and feeds it to the pug mill.     WATER TANK One / Two Water Tanks of 15 / 20 MT capacity each are provided, fabricated from steel plates with manhole, flowmeter, pump etc. CONTROL CABIN A fully automatic Control Panel is provided for controlling the quantity and quality of production with operator sitting in Air-conditioned comfort. MINERAL FILLER Fabricated from steel plates, it feeds the required quantity of additives to the pug mill. OPTIONAL Variable Feeding Device can be provided for Belt Feeder. Wet Mix Storage Silo.

  This is very easy to use at site for removal of the road dust easily on Metaling, Wet Mixed Macadam Surface & Asphalted Road Surface. This is Zero Maintenance machine for work and uses very less man Power.

  Hot gas from exhaust fan of thermo Drum enters into pollution control unit, very high pressured jet sprayed water on the gases thus, gases from in a slurry and are diverted to the sludge tank. Remaining gases released through exhaust by reducing the air pressure.

  Capacity to lay mat form 12 mm. to 200 mm. thick and 2.5 mtr. to 4.0 mtr. Wide bituminous mat. The Paver is powered by Kirlosker Diesel engine and mounted on front two nos. Solid rubber coated and rear two no’s Pneumatic tires. The Screed is Hydraulically drive with extension. Auto parts & spares are easily available. Power unit Simpsons / Kirlossker Diesel engine. Main 4 Speed forward Transmission 4 Speed reverse with Low / High range       Drive wheels 1000 X 20 – 16 ply Front wheel One Rubber coated steel wheel on each side rubber coated Brakes Air brakes on rear wheels thourth tandem master cylinder assisted by Single chamber air pressure booster, mechanically operated parking brake. Truck push roller Push roller are adjustable for height and reach. Screed 2500 mm width heavy duty having mechanical extension and extendable up to 4000 mm slides over premixed material. Hoppers Hydraulically operated folding hoppers. Feeders The Single bar conveyor chain feeds the material from bottom plate 10 mm thick made from wear resistant and heat resistant steel plate. Spreading Screw Mechanically driven 250 mm dia. hard surface welded.

  The dryer unit (Drum) rotating cylindralical drum mounted on robust steel structure, Chassis design for Vibration free rotation, whole structure provided with legs to give proper degree for best accurate result contra flow mixing system is provided for uninterrupted production. Uniform mixing of asphalt & aggregates with required temperature. Electronic High-Low burner Coontrol fuel through solenoid value with auto on-off system auto panel provided all function in fully auto/manual system

This is very easy to use at site for removal of the road dust easily on Metaling, Wet Mixed Macadam Surface & Asphalted Road Surface. This is Zero Maintenance machine for work and uses very less man Power.

This is very easy to use for Cutting Road divider. Also this is very fast and easy to operate with low maintenance and save time with deceased man power.

  This is very easy to use for Cutting Road divider. Also this is very fast and easy to operate with low maintenance and save time with deceased man power.

  Himakshi Kerber is a compact machine for laying concrete kerbs of different dimensions, through the extrusion process. An automatic Sensor divice provides steering and height control. The use of a zero slump concrete ensures shape true to the mould design. The concrete can be fed into the machine from a Concrete Transit Mixer or a flat bed truck (Tractor trolley) by shoveling process.

performance himakshi tailboard chipping spreader is designed to give a fast, accurately controlled application of surface dressing chippings, coated chippings and other materials on to all types of roads. The unit is designed for easy fitting to most tipping truck bodies, and is available in the following two models. 2.25m (7" 4") spreas 2.25m (8" 3") spreas each model is available with an optional quick release scatter plate, which extends the spreading width by 0.5 m (20") giving 2.75m(9') or 3.0 m (10')spread       variation in the spreading width can be achieved infinitely, from zero to maximum, by use of a lever controlled taper door control of the desired coverage is by a screw adjusted rubber gate mounted above the feed roller. Large foreign bodies pass through without causing damage. A metered application results by using spring loaded drive wheel, that automatically contacts the road surface as the body is tipped to the working position, and rotates the feed roller relative to ground speed through an operator controlled dog clutch. The main body design now incorporates a large throat with an adjustable battle to suit the different flow characteristics of the material to be spread. To further assist the flow and to material to be spread. To further assist the flow and to break up lumps of coated chippings, an optional agitator is available for fitting in the throat. when required a full width operator platform can be specified as an optional extra. This allows the operator to ride with the machine and operate the controls in greater safety. specification weight of 2.25 m model - 650 kg. (approx). weight of 2.2 m model - 700 kg. (approx). body constructed form 4mm pressed steel plate with hollow square and rectangular reinforcing cestions and channels. feed roller serrated surface feed roller constructed from 165 mm (11/2") diameter tube mounted between self aligning lubricated for life bearings. baffle (to control material surge) bolt on variaable position battle plate. adjustable from 100 mm to 250 mm in 50 mm increments. feedgate adjustable gate with hand operated adjusting screws. Bottom section of gale in rubber to permit passage of oversize objects without damage. note: for possible applications other than surface dressing the gate is removable. feed opening: 50mm(2") feed gate fitted: 75mm(3") feed remove cut off door (width of spread) infinitely adjustable from zero to maximum by lever controlled taper door, when baffle is either of its two lowest settings. When the baffles are in the two highest settings and depending on the material being spread, the cut off minimum width will vary. drive a 457 mm x 178 mm (24" x 7") pneumatic tyred wheel tansmits drive from the road surface through a 19 mm (3/4") chain drive from the road surface through a 19 mm (3/4") chain drive to a cast iron / m.s dog clutch. Mounted on a lay shaft. The drive is then transmitted through this shafts to a chain drive fitted to the feed roller. All shafts are mounted on self aligning, self lubricating ball bearings, with the clutch operated by levers either side of the unit. The roller chain drive is fully enclosed in a heavy duty guard designed to self clean. The drive wheel position is adjustable to suit truck bed heights down to 1100mm (43") optional extras platform platform with stand rails and across step either side. Weight 77 kg. (170lbs) agitators heavy duty tube with high tensile tongues, mounted in self aligning, self lubricated bearings. Chain drive from existing roller drive. Weight 11 kg. (24lbs)(approx). scatter plate a quick reales unit designed to exrend the existing width of spread uniformly by 0.5 (20") setting angle variable to suit chipping size and flow characteristics. For travelling the scatter plate the scatter plate ends can be foled in to reduce the machines overall width. weight 55kg. (121 ibs) (approx)

  Himakshi Road–Cons Equipments produces all type of Bitumen Sprayers for all type of Road Construction Industries Himakshi Road–Cons Equipments having beckbone of Techno Qualified mechanical engineers as proprietors and having fleet of skilled man power. Himakshi Road–Cons Equipments is a fast growing organisation having prime principle of customer Satisfaction by giving appropriate Technology, Quality & after Sales Servies at Reasonable Rates.

  We are Manufacturer of Asphalt Drum Mix Plant Since 1991. and we are exporters of Asphalt Drum Mix Plant, leading Supplier of Asphalt Drum Mix plants in India DRYER DRUM The dryer is accurately fabricated to ensure proper heating of aggregates with minimum heat loss. Specially designed flights lift and cascade the aggregate to reduce the final moisture content to 0.5% (by weight). It is supported on steel rollers through steel tyres with idlers and guide rollers and is provided with segmented driving sprocket. A fully automatic high-pressure auto jet burner is mounted at one end of the drum. The discharge chute design discharges heated aggregate directly onto the loadout conveyor. FOUR-BIN FEEDER It is of single chassis construction. At each Bin a radial gate is provided         which can be opened in any position to regulate the aggregate flow. Individual endless belts are provided below the gates to discharge material onto the gathering belt.   VIBRATING SCREEN A single-deck vibrating screen is provided on the slinger conveyor to remove oversize aggregate received from the 4-bin feeder. SLINGER CONVEYOR An inclined conveyor mounted on idlers receives aggregate from the gathering conveyor and feeds it to the dryer LOAD OUT CONVEYOR Mixed aggregate from the dryer drum is discharged on an inclined conveyor provided with a hydraulic hopper at delivery end for feeding the Mix into Tippers. BITUMEN TANKS One/Two Bitumen Tanks of 15/20/30 MT capacity each are provided, fabricated from steel plates with 50 mm glasswool insulation, manhole, thermocouples, etc. Bitumen is pumped to the dryer drum through pipe lines. Tanks are fitted with independent on-off type burners. MULTICYCLONE EXHAUST The dust collection system consists of enclosed multiple cyclones, exhaust fan and chimney. MINERAL FILLER Fabricated from steel plates, it feeds the required quantity of mineral to the drum. CONTROL CABIN A fully automatic control panel with feather touch controls is provided for controlling the quantity and quality of production with operator sitting in Air-conditioned comfort. All systems are completely synchronized with automatic / manual control of burners, load cells, mix temperature, cold feed / mineral / bitumen proportions, etc. Manual control is possible through over-ride system. Adequate safety measures are adopted to avoid overloading, short-circuit, etc. LDO TANK One LDO Tank of 2000 / 4000 Ltrs. Capacity is provided with each plant. OPTIONALS • Wet type air pollution control system. • Baghouse filter system. • Hot mix storage silo. • Portable plants.