Antique Designer Tiles GIDC, Morvi, Gujarat

We are counted among the trustworthy Manufacturers and Suppliers of Antique Platinum Adhesive (white) from morbi, Gujarat. These adhesives are manufactured by using qualitative raw compounds under the strict guidance of industry professionals. Our White Platinum Adhesives find their applications for both interior and exterior installations, which includes under water applications for fixing tiles, marble etc. Platinum Adhesive is known for their workability and high bonding strength.   Description : The ultimate one-step, polymer modified, thin-set mortar for interior and exterior installation of ceramic tile, stone, quarry tile, pavers and brick. Antique Platinum Adhesive , designed to just mix with water, has a long open time with unsurpassed adhesion and workability.Uses : Excellent for exterior and underwater applications, Like for fixing swimming pool tiles, marble, granite and all kind of ceramic tiles.Advantages : Exceeds Shear Bond Strength Requirements. Ultimate adhesion for porcelain and glass tiles. Superior for exterior and submerged applications. High shear bond strength. Smooth creamy formula. See limitations. Suitable Substrates : Concrete / Masonry . Concrete block . Cement mortar beds . Non-water soluble cut-back adhesive* Existing ceramic tile and stone Interior use only : Consult cement backer board manufacturer for specific installation recommendations and to verify acceptability for exterior use.Approximate Coverage : 55–60sft per 20kg bag with 1/4" x 1/4" (6 mm x 6 mm) notched trowel. Coverage will vary depending on trowel notch size, type and size of tile and substrate. Shelf Life : Factory sealed containers of this product are guaranteed to be of first quality for one (1) yearif stored off the ground in a dry area. High humidity will reduce the shelf life of bagged product. Packaging : 1kg, 20kg bagColor : WhiteLimitations : Not for use directly over particle board, luan, Masonite® or hardwood floors. Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a Antique Platinum Adhesive Waterproofing Membrane. Note : Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L=span length.Cautions : Consult MSDS for more safety information. Some marbles and other stone have low flexural strength and may not be suitable for installation over wood floors. During cold weather, protect finished work from traffic until fully cured. Contains portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water. Wait 14 days after the final grouting period before filing water features with water at 70°F (21°C) Do Not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas. Keep out of reach of children.  Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.Installation : Surface Preparation : All surfaces should be between 40°F (14°C) and 90°F (32°C) and structurally sound, clean and free of all dirt, oil, grease, paint, concrete sealers or curing compounds. Rough or uneven concrete surfaces should be made smooth with Antique Platinum Adhesive Latex Portland Cement Underlayment to provide a wood float (or better) finish. Dry, dusty concrete slabs or masonry should be dampened and excess water swept off. Installation may be made on a damp surface. Concrete slabs must be plumb and true to within 1/4" (6 mm) in 10 ft (3 m).Note : Antique Platinum Adhesive does not require a minimum cure time for concrete slabs. Expansion joints shall be provided through the tile work from all construction or expansion joints in the substrate. Follow ANSI specification A108.01-3.7 “Requirements for Movement Joints: Preparations by Other Trades” or TCNA detail EJ-171 “Movement Joints—Vertical & Horizontal”. Do not cover expansion joints with mortar. Installer must verify that deflection under all live, dead and impact L/360 for ceramic tile and brick or L/480 for stone installations where L=span length. Mixing : Place clean, potable water into a clean pail. Add Antique Platinum Adhesive. Use approximately 5-5.5 litres of water for 20kg of powder. Mix by hand or with a slow speed mixer to a smooth, trowelable consistency. Allow mortar to slake for 5–10 minutes. Remix with out adding any more water or powder. During use, stir occasionally to keep mix fluffy. Do Not temper with water.Application : Apply Antique Platinum Adhesive to the substrate with the flat side of the trowel, pressing firmly to work into surface. Comb on additional adhesive with the notched side. Note : Use proper sized notched trowel to ensure full bedding of the tile. Spread as much mortar as can becovered with tile in 15–20 minutes. Back butter large tiles >8" x 8" (>200 mm x 200 mm) to provide full bedding and firm support. Place tiles into wet, sticky mortar and beat in using a beating block and rubber mallet to embed tile and adjust level. Check mortar for complete coverage by periodically removing a tile and inspecting bedding mortar transfer onto back of tile. If mortar is skinned over (not sticky), remove and replace with fresh mortar.Grouting : Grout the installation after a minimum of 24 hours curing time at 70oF (21oC). Grout with Antique TG Silver Sanded Grout or Antique TG Golden Unsanded Grout mixed & Antique Platinum Grout Admix Plus. For maximum stain resistance use Antique Platinum Adhesive Stain free Grout for Floor N’ Wall.Maintenance : Antique Platinum Adhesive grouts require routine cleaning with a neutral pH soap and water. All other Antique Platinum Adhesive materials require no maintenance but installation performance and durability may depend on properly maintaining products supplied by other manufacturers.Warranty : Antique Designer Tiles warrants that Antique Platinum Adhesive is free from manufacturing defects and will not break down, deteriorate or disintegrate under normal usage for a period of one (1) year from date of purchase subject to the terms and conditions stated in Antique Platinum Adhesive Product Warranty.

Brand Name : Antique Platinum Adhesive (white)

We are Manufacturer and Supplier of SBR Waterproofing from Surat, Gujarat. Latex Waterproofing Adhesive is SBR based liquid and widely used for high performance applications such as waterproofing and repairing cracks. We pack Latex Waterproofing Adhesive in air-sealed bags to keep it free from moisture. For purchasing Latex Waterproofing Adhesive at pocket friendly rates, contact us.   Areas of Application : As bond coating Plaster to plaster, concrete to concrete, For plaster over brick masonry As waterproof repair plaster As crack repair Plaster cracks more than 5 mm, In gaps developed between masonry and RCC members. As coating for prevention of corrosion in rebars Efflorescence (salt petre/damp surfaces) Method of Application :Surface Preparation - Surface for treatments must be thoroughly cleaned of all laitance, loose material, oils, grease, etc. Mechanical means such as wire brushing, shot blasting can be used and finally vacuum cleaned of all loose solids and liquids. Before application ensure that the surface is damp but in a touch dry condition. Curing - 3 to 5 days with a wet hessian or jute cloth, or water spray.  Features : Excellent Coverage -70-80 sq.ft per kg/ in 2 coats, hence economical Less material wastage- material does not fall back/ rebound, when used as bonding agent High Bond Strength Prevents leakage & dampness Enhances strength of a repair mortar & provides durability Precautions & Limitations : Strictly do not dilute beyond recommendation To be applied over damp substrate but in a dry to touch state Not suggested for use in very critical concrete repairs Waterproof coats with Antique Super Latex - 555 SBR must be protected with screeds/plasters When applying as a bond coat, if it becomes dry, re-apply to reach a tacky state for overlay of concrete or mortar 2nd coat of plaster with Antique Super Latex - 555 SBR may cause a problem in external painting of the surface Technical Information : Type - Styrene Butadiene Polymer Liquid Color - White Specific Gravity - 1.02 + 0.02 Storage Condition - Free from frost Solid Content - 44 + 1% For best result - use before 1 year if unopened Consumption - 1 kg of super latex will cover 70 - 80 sq. ft. area in 2 coats for a proportion mix 1:4:7 ( Super Latex : Water : Cement) Packing : 250 g, 1 kg, 5 kg & 20 Kg

Owing to our rich industrial experience and rich knowledge, we are engaged in manufacturing and supplying of Super Bond Waterproofing Adhesive from Surat, Gujarat. Our Waterproofing Adhesives are manufactured by using high quality compounds in line with set quality norms. We can make available our Waterproofing Adhesive in varied specifications as per buyer’s need and that too at nominal rates.

Being a reputed Manufacturer and Supplier, we are offering a quality range of Antique Cem Bond Waterproofing Adhesive (AW+111) from morbi, Gujarat. Waterproofing Adhesive is precisely formulated by using waterproofing compounds. It is an integral liquid water proofing compound for concrete & plaster. Our Waterproofing Adhesive makes concrete cohesive and available with us in different packaging standards.   Description : Antique Cem Bond AW+111 is specially formulated integral liquid waterproofing compound composed of surface active. Plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.Areas of Application Waterproofing of concrete and sand-cement mortars used in  Basements  Roof slabs and screeds  Water tanks & water retaining structures  External plastering  Bathrooms and balconies  Sumps and drains Features & Benefits :  Corrosion resistant - Makes concrete more cohesive, hence protects steel better against corrosion  Compatibility – Being a liquid, easily dispersible & compatible with concrete/mortar mixes.  Permeability – It reduces the permeability of water into concrete.  Strength – The setting time and compressive strength of the concrete remains within the specification limits.  Shrinkage – Reduces shrinkage crack development in plaster & concrete.  Workability – Improves workability of freshly mixed cement concrete.  Durability – Increases durability by improving waterproofing of concrete. Method of Application :  Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes.  Start addition of 75–80% mixing water & mix for 2-3 minutes.  Antique Cem Bond AW+111 is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 minutes.  Place the concrete or apply plaster, as needed .  Cure the applied mortar or concrete as per good construction practices. Precautions & Limitations : Do not add Antique Cem Bond AW+111 directly to dry cement & aggregate mix. Maintain water-cement ratio as low as possible. Do not increase the dosage of Antique Cem Bond AW+111 than the recommendation.  Dosage : 200 ml per 50 kg bag of cementPacking : 200 ml, 1, 5 , 20 & 200 literShelf Life & Storage :  Shelf life is 12 months from the date of manufacturing in unopened conditions.  Store in a cool & dry place. Health & Safety Precautions :  Use rubber hand gloves & safety goggles, while using Antique Cem Bond AW+111.  In case of contact with skin, wash with plenty of water.  Keep out of reach of children.

We are Manufacturer and Supplier of Antique Wall Putty from Surat, Gujarat. The product is made from high quality compounds and processed by using advanced tools and techniques. Antique Wall Putty, water resistant white cement, ideal for using on concrete and mortar walls and ceilings and provides a smooth and white surface, essential for painting. Our Antique Wall Putty can be applied on moist surface. Offered product is durable and its high strength features enhance the life of paints. Also, it does not require water curing.   Salient features of “Antique Wall Putty” :  Being a cementitious material it has better adhesiveness and durability. “Antique Wall Putty” can be applied on both interior and exterior surfaces. “Antique Wall Putty” does not require any curing.  It is water resistant and can be applied on moist surface. It is recommended that two coats of Birla  White cement wash be done before application of “Antique Wall Putty”. “Antique Wall Putty” gives a smooth and glossy finish.  Any kind of paint or distemper can be applied on it.  No need to apply any kind of primer on it before application of paint/distemper.  It can be applied on used surface after proper preparation.  It prevents the growth of algae and fungi on walls.  It is in dry powder form and does not produce any kind of unpleasant smell at the time of application. Application Procedure : Remove all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and clean water. The substrate should be clean, free from dust, grease and loose materials. Dry and absorbent surfaces should be moistened with sufficient quantity of clean water.Mix “Antique Wall Putty” with 30-35% clean water slowly to make paste. Continue the mixing for 10-15 minutes till a uniform paste is formed. After thoroughly mixing “Antique Wall Putty” apply the first coat on already moistened wall surface from bottom to upward direction uniformly with the help of putty blade. This would ensure less wastage and proper finish. After drying of first coat of putty just rub the surface gently with west sponge or rub the surface very gently with the putty blade in order to remove the loose particles. Allow the surface to dry for atleast 3 hours and then apply second coat of putty. Leavethe surface to dry completely. After drying of second coat remove marks if any with the help of moist sponge or rub the surface very gently with the putty blade. Leavethe surface to dry preferably for overnight. Always prepare a required quantity of putty and use it within 2-3 hrs. of mixing with water The total thickness of the coats should be limited to maximum 1.5mm. It is not essential to rub the surface done with “Antique Wall Putty”, however if you need to remove unevenness before applying any kind of paint/distemper, gently level the walls/ceiling surface with very fine water proof emery paper of not less that 500 number to get a glossy white surface.Precautions During Application : Mixing of “Antique Wall Putty” is very important and hence extreme care is to be taken for proper and thorough mixing with hand or mechanical stirrer in order to get best results. “Antique Wall Putty” Should be done over fully cured surface. It is recommended not to rub “Antique Wall Putty” strongly and harshly with rough emery paper. This breaks the film formed over “Antique Wall Putty”, which Decreases the water repellency properties. The total thickness of the coat should be limited to maximum 1.5mm. In case of fresh concrete/mortar surface it is recommended that two coats of Birla White cement Wash be done before application of “Antique Wall Putty”. Coverage : The coverage area of “Antique Wall Putty” on smooth normal mortar wall is 20 to 25 Sq. Ft/Kg/mm in double coat. The coverage area, however, will depend upon the quality of the substrate.Note : Generally the cause of efflorescence on the walls surface is the brick masonry, which is due to the quality of bricks, sand and water, If the effect of efflorescence on the brick masonry seems to be very high then proper Care should be taken to control the efflorescence. The efflorescence problem on brick masonry if exists impairs the bonding of “Antique Wall Putty” as is with any other product. Packing : “Antique Wall Putty” is available in 1Kg, 20Kg And 40Kg Packs.

Since its inception, we are offering a high quality range of Antique Tile Spacer to our esteemed customers all over the country. The product is precisely manufactured by using qualitative raw material in tune with set industry norms. Antique Tile Spacer is available with us in different specifications such as 2mm, 3mm, 4mm, 5mm, 8mm, and 10mm. Being a client-centric company, we offer our Antique Tile Spacer at nominal rates to our customers.

The company has cemented its presence among the reliable Manufacturers and Suppliers of Antique Tile Grout Silver from Surat, Gujarat. The product is made from quality-approved raw material under the guidance of supervisors at our production unit. Our Silver Water Resistant Tile Grout is used for grouting of tiles, stones etc. Water repellency properties, excellent adhesion and workability make our Antique Tile Grout high in demand.   Description : Antique Tile Grout Silver is a fine powder consisting of portland cement, specially selected polymer, properly selected & graded fine fillers, additives and inorganic chemicals. It is used for grouting of tiles, stones, marble joints & edges because it has water repellency properties, excellent adhesion (high bonding strength), soft consistency, workability and seals joint permanently. It is non-shrinking, non-toxic and odourless grout used for sealing of swimming pool & water tank joints as well.Areas of Application : Antique Tile Grout Silver is used for grouting of ceramic tiles, marbles, natural stones and edges. Specially formulated for wet or submerged grouting applications such as swimming pool, bathrooms, toilets, fountains and kitchen areas. It can be used for external and internal areas. It is used in residential and commercial areas. Application up to joint width of 2-4mm. It is excellent for highly glazed tiles to give a smooth and watertight joints which when set will be both water and mould resistant. Features & Benefits :Aesthetics – Available in specify shades. Easy to use – Easily to mix with water and forms soft consistency paste which is easy to fill the joints. Shrinkage & cracking - Avoids cracks formation in the joints and also there is negligible shrinkage. Service Temperature - Specially formulated for temperature range of 5° – 120°C.  Water resistant – Excellent water-resistance making it beneficial for application in areas immersed under water.  Durability & UV resistant - Excellent UV resistance & durability enables the product use for exterior application.  High Strength & abrasion resistant – High strength & abrasion resistance properties makes it suitable for grouting of toilets & bathrooms. Method of Application : Surface Preparation :  Surface must be cleaned and should be free from dirt, cured tile adhesive. Remove dust with wire brush & by air blower.  For exterior grouting application, wet the tiles prior to applying Antique Tile Grout Silver. Mixing :  Add the grout powder to the mixing water (w:p ratio – 1 : 2.5 by volume) and mix with slow speed drill (250-300 rpm) to a soft & smooth consistency paste.  If the grout mortar has become too stiff to work, it should be discarded and a new batch should be prepared. Application : Apply to the tile joints with squeegee, spatula or putty blade. After application flush the surface of tile using a hard rubber float, working diagonally across the grout joints to fill and compact the joints. All excess grout should be removed with the same rubber float without any delay. Lesser the quantity of grout left on the face of the tiles while application, the final cleaning will be easier. with Antique Tiles & Grout Cleaner - 225. However, it is important to allow the grout to set in the joint and to let it acquire its initial set before any further cleaning. After the initial set of the grout, clean the tile surface with a pad of cheesecloth or towel dampened with minimum quantity of clean and cool water. Rub in a circular motion to further compact the grout. The remaining surface grout on the tile can also be cleaned at this time. Scrubbing pad fastened to a float works very well to remove grout from the porous tiles. Rebuff the tile surface and grout within 1-2 hours to remove all weep water and grout residue from the surface, which helps to reduce the efflorescence and to control colour variation. Cleaning : Polish the tiles when the job is complete with a clean dry cloth. Scrubbing the floor with hot water and soap water is the best. Due to polymer content, it is advisable to clean the surface immediately after the grouting. Precautions & Limitations : Do not mix excess water. Antique Tile Grout Silver cannot be used where high acid resistance is required because of its cement base. The potential for efflorescence is inherent in all cement-based products and it is not to be considered as a manufacturing defect.  # The water Absorption test results complies with the ANSI 118.6 specification limitCoverage : Refer Table for the consumption of Antique Tile Grout Silver for various sizes of tiles Pls. Add 5 % wastage in TG consumption mentioned above. Packaging - 500gm, 1kg & 20kg.Shelf Life & Storage : -Shelf life is 12 months from the date of manufacturing in unopened condition. -Store in a cool & dry place. Health & Safety Precautions : Protective clothing, such as gloves and goggles, should be worn. Treat any contact to the skin or eyes with fresh water immediately. Do not induce vomiting & seek medical Assistance immediately. Reseal pack after use and ensure product is stored as instructed..

We are acknowledged Manufacturer and Supplier of Antique Tile Grout Golden (High Polymer) from Surat, Gujarat. Our Antique Tile Grout is a high polymers powder composed of Portland cement. Golden Antique Tile Grout, offered by us, is widely demanded due to its water resistance, high bonding strength and soft consistency. Our Water Resistant Tile Grout is non-toxic and non-shrinking and widely used for sealing of swimming pools & water tank joints.   Description : Antique Tile Grout Golden is a High Polymer based fine powder consisting of portland cement, specially selected polymer, properly selected & graded fine fillers, additives and inorganic chemicals. It is used for grouting of tiles, stones, marble joints & edges because it has water repellency properties, excellent adhesion (high bonding strength), soft consistency, workability and seals joint permanently. It is nonshrinking, non-toxic and odourless grout used for sealing of swimming pool & water tank joints as well.Areas of Application : Antique Tile Grout Golden is used for grouting of ceramic tiles, marbles, natural stones and edges. Specially formulated for wet or submerged grouting applications such as swimming pool, bathrooms, toilets, fountains and kitchen areas. It can be used for external and internal areas. It is used in residential and commercial areas. Application up to joint width of 2-10mm. It is excellent for highly glazed tiles to give a smooth and watertight joints which when set will be both water and mould resistant. Features & Benefits : Aesthetics – Available in specify shades. Easy to use – Easily to mix with water and forms soft consistency paste which is easy to fill the joints. Shrinkage & cracking - Avoids cracks formation in the joints and also there is negligible shrinkage. Service Temperature - Specially formulated for temperature range of 50– 1500C.  Water resistant – Excellent water-resistance making it beneficial for application in areas immersed under water.  Durability & UV resistant - Excellent UV resistance & durability enables the product use for exterior application.  High Strength & abrasion resistant – High strength & abrasion resistance properties makes it suitable for grouting of toilets & bathrooms. Method of Application : Surface Preparation :  Surface must be cleaned and should be free from dirt, cured tile adhesive. Remove dust with wire brush & by air blower.  For exterior grouting application, wet the tiles prior to applying Antique Tile Grout Golden Mixing :  Add the grout powder to the mixing water (w:p ratio – 1 : 2.5 by volume) and mix with slow speed drill (250-300 rpm) to a soft & smooth consistency paste.  If the grout mortar has become too stiff to work, it should be discarded and a new batch should be prepared. Application : Apply to the tile joints with squeegee, spatula or putty blade. After application flush the surface of tile using a hard rubber float, working diagonally across the grout joints to fill and compact the joints. All excess groutshould be removed with the same rubber float without any delay. Lesser the quantity of grout left on the face of the tiles while application, the final cleaning will be easier with Antique Tiles & Grout Cleaner - 225. However, it is important to allow the grout to set in the joint and to let it acquire its initial set before any further cleaning. After the initial set of the grout, clean the tile surface with a pad of cheesecloth or towel dampened with minimum quantity of clean and cool water. Rub in a circular motion to further compact the grout. The remaining surface grout on the tile can also be cleaned at this time. Scrubbing pad fastened to a float works very well to remove grout from the porous tiles. Rebuff the tile surface and grout within 1-2 hours to remove all weep water and grout residue from the surface, which helps to reduce the efflorescence and to control colour variation. Cleaning : Polish the tiles when the job is complete with a clean dry cloth. Scrubbing the floor with hot water and soap water is the best. Due to polymer content, it is advisable to clean the surface immediately after the grouting. Precautions & Limitations : Do not mix excess water. Antique Tile Grout Golden cannot be used where high acid resistance is required because of its cement base. The potential for efflorescence is inherent in all cement-based products and it is not to be considered as a manufacturing defect.  The water Absorption test results complies with the ANSI 118.6 specification limitCoverage : Refer Table for the consumption of Antique Tile Grout Golden for various sizes of tiles Pls. Add 5 % wastage in TG consumption mentioned above. Packaging - 500gm, 1kg & 20kg.Shelf Life & Storage : -Shelf life is 12 months from the date of manufacturing in unopened condition. -Store in a cool & dry place. Health & Safety Precautions : Protective clothing, such as gloves and goggles, should be worn. Treat any contact to the skin or eyes with fresh water immediately. Do not induce vomiting & seek medical Assistance immediately. Reseal pack after use and ensure product is stored as instructed..

We bring forth a qualitative range of Antique Tile Grout (German Based) to our customers all over the country. Based in Surat, Gujarat, we are Antique Tile Grout Manufacturer and Supplier. Antique Tile Grout is formulated by using high quality ingredients in line with set industry norms. Owing to our vast network, we can provide German Based Antique Tile Grout in custom made specifications as per buyer’s need.

Brand Name : Antique Tile Gout (german Technology)

We are recognized Manufacturer and Supplier of Antique Flexi Bond Waterproofing Adhesive from Surat, Gujarat. Waterproofing Adhesive, that we offer, is made to provide protection for concrete from seawater. Due to its long lasting effects and quality features, our Waterproofing Adhesives are highly appreciated. Buy from us Waterproofing Adhesive in different quantity and packaging at unbeatable market rates. We assure safe and timely deliveries.   Features & Benefits : Waterproofing - Exceptionally good waterproofing. Ease of application - Cold applied, bituminous emulsion material. Easily applied by brush or mop. Durability - Forms relatively thick (1.2-1.5 mm) film providing excellent impermeable and durable membrane. Movement accommodation - Polymer modified hence forms flexible film. Also accommodates thermal stresses in slab due to variation in temperature. Reinforcement – Higher reinforcement can be induced with polyester fibre sheet between the coats. Self priming – No separate or additional primer is required. Method of Application : Surface Preparation : Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. Mechanical means such as wire brushing & shot blasting can be used. Finally vacuum cleaning of all loose solids and liquids can be done if required. All surface cracks up to 5 mm width should be filled up with Antique Non Shink Crack-x. Cracks more than 5 mm and all separation gaps should be filled up with Antique Flexi Bond URP Modified Adhesive as specified. Application : Apply Three coats directly by brush or mop and dilute Antique Seal - 115 with three part of water & one part of Antique Seal - 115 powder. Apply 2nd & 3rd coat in gapes of two or three hours. Cleaning : Tools & equipments should be cleaned with potable water immediately after use. Cured material can be cleaned by scrapping  Precautions & Limitations : Dilute with water for application. Not recommended for areas larger than 2000 sq. ft. Always protect the coating with proper and appropriate screeding. Do not keep it exposed to UV Coverage : 1kg meterial gives coverage 10 to 15 sq. ft.(Three coats) Coverage may vary depending upon the texture and porosity of the surface Packaging - 1, 5kgShelf Life & Storage : Shelf life is 12 months from the date of manufacturing. Store in a cool & dry place. Keep away from direct sun light Health & Safety Precautions : During application wear protective clothing, gloves and eye goggles during application. Avoid product to contact eyes and skin. Skin Contact : Wash immediately with plenty of clean water. Eye contact : In the event of eye contact splash plenty of clean water immediately and seek medical advice.

We are Manufacturer and Supplier of Antique Master Coat from Surat, Gujarat. Made as per the international quality standards, our Antique Master Coat is known for its optimum quality features. The product is used as a waterproof coating for roofs. It has excellent Acrylic reinforced cementitious property. We have advanced production technology, so we can provide Antique Master Coat in different specifications as per buyer’s need. We offer Antique Master Coat at pocket friendly rates, contact us.   Description : Antique Master Coat-550 is a two component acrylic modified cementitious system that requires only on site mixing forming the ideal coating to waterproof and resurface concrete, masonry, and most other construction materials.Simply applied by stiff brush, roller, or trowel, it forms a waterproof, flexible coating.Uses : As a waterproof lining for water retaining structures. As a waterproof coating for roofs. To provide foundation protection. For coating seawater channels. To provide protection to concrete surfaces from carbonation and chloride attack. Sealing and coating tie bar holes to ensure watertightness. For waterproofing and protection against brackish water. As a backing to marble and granite to prevent water ingress and thus eliminates surface staining. Advantages : A 1mm coating provides anti carbonation cover equivalent to over 80cm of concrete. Waterproof-resists up to 7 Bars (70 metre head) of pressure when applied at 2mm DFT. Provides barrier to water borne salts. Excellent adhesion. Bonds to porous and non-porous surfaces. Flexible. Non toxic suitable for contact with potable water. Suitable for light pedestrian traffic. Breathable - whilst repelling water, allows substrate to breathe. High resistance to carbon dioxide and chloride ion diffusion. Can be applied to 24 hour-old concrete thereby giving immediate protection. Specification Clause : All exposed concrete surfaces are to be coated with Antique Master Coat-550, a two component reactive polymer composite. The product shall be applied in minimum two coats to achieve total DFT of 1mm. The product shall resist 7 bars pressure when tested as per DIN 1048 at 2mm DFT. The cured coating shall have the following diffusion co-efficient.Directions for use : Surface preparation : The surface to be coated must be clean and sound. Remove all traces of formwork, release agents, previous coatings, laitance and any other contaminants that may affect the bond adversely. Suitable cleaning methods include high pressure water jetting and grit blasting. Mechanical wire brushing may be appropriate for small areas. After the above surface preparation, surfaces must be thoroughly washed with clean potable water to remove all dust and loose particles. Spalled concrete should be cut back to sound concrete and made good with a suitable cementitious repair mortar such as Antique Non Shrink Crack Filler. All cracks and bolt holes must be cut out and filled solid with Antique Master Coat-550 or Antique Seal-115. Mixing : Antique Master Coat-550 is supplied in premeasured units and should be mixed on site utilising clean containers. Slowly add the powder to the liquid and mix, using a slow speed drill fitted with a suitable paddle. Leave the mixed material to stand for 5 minutes to allow for full saturation to take place. Remix to restore the consistency. Do not mix more material than can be used in half an hour. Do Not Re-temper with Water.Application : Always apply Antique Master Coat-550 to pre-dampened surface. High-suction substrates require more dampening then dense substrates. However, make sure there is no free-standing water. Apply by brush or broom. Mixed material must be used with in 30 -45 minutes, or less under hot weather conditions. First Coat : Brush or broom the mix firmly onto the pre-dampened, prepared surface. Care must be taken not to spread the material too thinly. When the material begins to drag or “ball”, do not add more liquid/water but dampen the surface again. Second Coat : Allow at least overnight to cure before applying subsequent coats. Dampen the first coat and remove excess moisture. Brush or broom the mix onto the surface (as above) finishing in the opposite direction to the first coat. Antique Master Coat-550 can be spray applied but should afterwards be brushed well into the substrate to ensure proper adhesion. To avoid this apply first coat by brush and second by spray application. Finally finish with sponge to get a uniform aesthetic appearance. Curing : Under hot or excessive drying conditions fog-spray after the initial set has taken place for as long as practicable. In cold, humid or unventilated areas it may be necessary to leave the application for a longer time curing period or to introduce forced air movement. Never use dehumidifiers during curing periods. Equipment Cleaning Not hardened material may simply be removed with water. Coverage : Each square metre will require minimum of 0.9 Kg of mixed material per layer. The coverage rate for each layer will be strongly influenced by the roughness of the substrate. 1.8 kg / m2 in two coats to achieve 1 mm thickness. Packaging : Antique Master Coat-550 is available in 10kg & 5 Kg packs and in white and grey colours.Storage and Shelf life : Store under cover, out of direct sunlight and protect from extremes of temperature. In tropical climates the product must be stored in an air-conditioned environment. Shelf life of the powder is 6 months and liquid is 12 months when stored as recommended. Disclaimer : Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.

We are counted among the trustworthy Manufacturers and Suppliers of Antique Epoxy Grout from Surat, Gujarat. Our product is known for its high quality features and optimum performance. In order to cater the best quality product to our prestigious customers, we test our Antique Epoxy Grout on several parameters for quality assurance. We offer Antique Epoxy Grout at budget friendly rates.

We bring forth an Antique Base Wall Mortar which is a new innovation for wall coating in India. Antique Base Wall Mortar, water resistant Luster wall coating, is widely used for interior as well as exterior use. Our Antique Base Wall Mortar is crack proof, weather proof and makes building components totally waterproof. We provide Antique Base Wall Mortar in standard packaging and can also provide in custom-made specifications as per buyers request.   Salient features of “Antique Wall Mortar” : Make building component Totally Water Made wall totally crackproof with high bonding. Colour resistancy as well as Weatherproofing. Use for interior as well as exterior coating. Get Luster Finish With UV Resistance and Eco friendly’’Antique Wall Mortar” Application Procedure : Remove all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and clean water. The substrate should be clean, free from dust, grease and loose materials. Dry and absorbent surfaces should be moistened with sufficient quantity of clean water. Mix “Antique Wall Mortar” with 60-65% clean water slowly to make paste. Continue the mixing for 10-15 minutes with putty grind machine till a uniform paste is formed. After thoroughly mixing “Antique Wall Mortar” apply the first coat with Antique base mortar on already moistened wall surface from bottom to upward direction uniformly with the help of putty blade. This would ensure less wastage and proper finish. After drying of first coat of Antique base mortar just rub the surface gently with west sponge or rub the surface very gently with the putty blade in order to remove the loose particles. Allow the surface to dry for atleast 24 hours and then apply second coat of with Antique finish mortar Leave the surface to dry completely. After drying of second coat remove marks if any with the help of moist sponge or rub the surface very gently with the putty blade. Leave the surface to dry preferably for overnight. Always prepare a required quantity of putty and use it within 2-3 hrs. of mixing with water The total thickness of the coats should be limited to maximum 1.5mm. It is not essential to rub the surface done with “Antique Wall Mortar”, however if you need to remove unevenness before applying any kind of paint/distemper, gently level the walls/ceiling surface with very fine water proof emery paper of not less that 500 number to get a glossy white surface. Precautions During Application : Mixing of “Antique Wall Mortar” is very important and hence extreme care is to be taken for proper and thorough mixing with hand or mechanical stirrer in order to get best results. “Antique Wall Mortar” should be done over fully cured surface. It is recommended not to rub “Antique Wall Mortar” strongly and harshly with rough emery paper. This breaks the film formed over “Antique Wall Mortar”, which decreases the water repellency properties. The total thickness of the coat should be limited to maximum 1.5mm. In case of fresh concrete/mortar surface it is recommended that two coats of Antique Base Mortar be apply before application of “Antique Wall Mortar”.Coverage : The coverage area of “Antique Base Wall Mortar” on smooth normal mortar wall is 25 to 30 Sq. Ft/Kg/mm The coverage area of “Antique Finish Wall Mortar” on smooth normal mortar wall is 35 to 40 Sq. Ft/Kg/mm The coverage area, however, will depend upon the quality of the substrate. Note : Generally the cause of efflorescence on the walls surface is the brick masonry, which is due to the quality of bricks, sand and water, If the effect of efflorescence on the brick masonry seems to be very high then proper care should be taken to control the efflorescence. The efflorescence problem on brick masonry if exists impairs the bonding of “Antique Wall Mortar” as is with any other product.  For High Effected efflorescence walls Contact our Customer Care for solution. Packing : “Antique Base Wall Mortar” is available in 20Kg Pack. “Antique Finish Wall Mortar” is available in 10Kg Box Pack.

We are prominent Manufacturer and Supplier of Antique Adhesive Silver (Grey) from Surat, Gujarat. It acts a waterproof barrier between two surfaces and gives excellent bonds on concrete, plaster etc. Our Silver Adhesive is widely used for fixing tiles. Its low shrinkage ability prevents tile from cracking. We offer Silver Adhesive at pocket friendly rates to our customers.   Description : Antique Adhesive Silver (Grey) is composed of ordinary portland cement properly selected & gradedaggregates, polymer, rheology modifier & additives. It is used for fixing of tiles internally & externally floorsbecause it gives excellent bond on cementitious surfaces like, concrete, plaster, etc. It forms a waterproof barrierbetween two surfaces and has excellent ‘grab’ properties of tiles to the substrate.Areas of Application : For fixing all types of Flooring tiles on internal & external, Floors. Features & Benefits : Ease of application - Ready to use, needs only mixing with water. Adhesion - Excellent adhesion prevent falling of tiles. Shrinkage - Low shrinkage hence prevents cracking of tiles & joints. Flexibility - Sufficiently flexible to accommodate physical & thermal movements. Water resistance – Excellent water resistance. Curing - Needs no water curing, hence saves labour & time. Traffic ability - Floors can be used after 24 hours of application. Soaking -Soaking of tiles & backing of surface not required Slip resistance – Non slip resistance is an advantage to fasten the work Toxicity – Non toxic Method of Application : Surface Preparation : The surface should be sound, clean, and free from dirt, oil or grease before Antique Adhesive Silver (Grey) is applied. Substrate should be in Saturated Surface Dry (SSD) condition before application of adhesive. Substrates should be in plumb before application of adhesive Mixing : Mix 20 kg of Antique Adhesive Silver (Grey) with 5 to 5.5 liters of water. Mix to a uniform lump-free consistency using a forced action mixer. Keep it for approximately 5 minutes to fatten it. Hand mixing is recommended for small quantities only. Mix as much quantity as can be consumed in 60 min. Application : Apply Antique Adhesive Silver (Grey) paste on substrate with plain side of notch trowel. Press paste firmly to work into substrate. Comb with notch trowel with notched side, notch trowel to be selected as per required bed thickness. Spread as much adhesive paste as can be tiled within 15 minutes. Start placing/fixing of tiles & tap using beating block or rubber mallet. For large format tiles & stone provide back butter for 100 % coverage & firm bonding. Periodically remove a tile to check transfer of material on tile. Also check spread of adhesive, if not proper and if becomes non-sticky then scrap it & apply paste again.. Grouting : Grouting should preferably be carried out at least 24 hours after the completion of tiling For grout joints upto 3mm wide use Antique Adhesive Silver (Grey) For grout joints above 3mm wide use RTM Wide. After grouting clean and polish tiles with a damp sponge or cloth Cleaning : Clean the tools & equipments with potable water immediately after use. Precautions & Limitations : Always add powder to liquid and not liquid to powder. While working in temperature more than 35OC ( 95OF ) always dampen the substrate & finish faster. Tiling should not be done when surface temperature is below 4OC. Antique Adhesive Silver (Grey) should not be used on painted , metal surfaces, ply & gypsum boards.  Coverage : 3.5 kg / m2 for 3 mm bed thickness. 7.0 kg / m2 for 6 mm bed thickness. Packaging : 20 kgShelf Life & Storage : Shelf life is 12 months from the date of manufacturing in unopened condition. Store in a cool & dry place.Health & Safety Precautions : As with all chemical products, caution should always be exercised. Protective clothing, such as gloves and goggles, should be worn. Treat any contact to the skin or eyes with fresh water immediately. Do not induce vomiting & seek medical assistance immediately. Ensure the pack is available for the medical attendant to examine any relevant instructions and content details. Reseal all containers after use and ensure product is stored as instructed.

We are Manufacturer and Supplier of Antique Adhesive Golden (White) from Surat, Gujarat. Golden Adhesives are obtained from blended polymers under the guidance of skilled personnel. Its excellent grabbing properties make our Golden Adhesive highly demanded among the buyers. Golden White Adhesive in used for both interior and exterior wall, floor & tile on tile applications.   Description : Antique Adhesive Golden (White) is a blended polymer modified white cement based powder tile adhesive. It gives excellent bond on cementitious surfaces like, concrete, plaster, etc. Antique Adhesive Golden (White) forms a waterproof barrier between two surfaces and has excellent 'grab' properties. Area of Application : For fixing all types of wall tiles on internal wall / floor, external floor & tile on tile applications. As well as swimming pool tiling applications.Features & Benefits : Ready to use, needs only mixing with 6 Ltr. water in 20kg bag. Excellent adhesion, low shrinkage Suitable for indoor and tile on tile applications Sufficiently flexible to accommodate physical & thermal movements Needs no curing, needs no hacking or mechanical key on the surfaces Floors can be used after 24 hours Curing not required Soaking of tiles & backing of surface not required Method of Application : The surface to be tiled should be clean and sound. Old surfaces must be free from wax, grease, polish, etc. The surface to be tiled should be sound and thoroughly cleaned. Old surface should be free from wax, grease,polish etc. Pour one 20 kg. Bag in approx. 6 lt. of clean water (recommended proportion approx. 3:1 of powder to water by volume). At site, addition of water shall be adjusted to attain desired consistency. Do not put water into the powder. Mix with a trowel / slow speed drills (50 - 100 rpm) until a lump free homogeneous paste is obtained. Always mix the required quantity, which can be consumed with in the prescribed pot life adopting the mixing proportion mentioned above. Spread the adhesive to a thickness of approx. 3-6 mm and comb with a notched trowel. Strictly apply the adhesive paste which can be tiled with in 10 to 15 mins. Intermittently touch the adhesive paste on substrate by finger. If the adhesive sticks to fingers then continue tiling and if not scrape off the adhesive and apply new coat. Start placing the tiles on the surface to be tiled. Tap the tiles properly to ensure complete coverage of the backside of tiles and to eliminate the possibility of any air voids. Keep joints between two-tiles using spacers that are available with Antique Adhesive Golden (White) bag. Allow tiling to set for 24 hours and start filling joints next day. Use mechanical clamps for holding the heavy stones in positions on vertical surface. Antique Adhesive Golden (White) also can be applied at 3-mm thickness for fixing of normal tiles in toilets and swimming pool area.  Precautions & Limitations : Do not use for vertical cladding of heavy tiles Always add powder to water and not water to powder Do not add more water than recommended Do not add sand or cement at site Before doing tile-on-tile application, ensure that the original tiling surface is in sound condition. In case of undulations in the existing floor, rectify the same before applying Antique Adhesive Golden (White) Strictly not recommended for the direct use on gypsum plaster, paint, wood & metal. For such applications apply Antique Adhesive Golden (White) over a dry & clean surface. Thereafter within 60 mins start applying without excessive deflection. Consult Antique Adhesive Golden (White) Packing : 20 kg

As a quality driven company, we are offering an exclusive range of Tiles Trowel all over the country. Tiles Trowels are manufactured by using high-grade metal and advanced tools and techniques at our production house. Tiles Trowel, we deal in, is a handheld tool widely used for spreading mortar or plaster. We can make available our Antique Wall & Floor Tiles Trowel in custom-made specifications as per specific demand of buyer.

As a reliable Manufacturer and Supplier, we bring forth a wide range of Acrylic Sealant to our customers all over the world. Our Acrylic Sealant is widely used for sealing objects and makes them airtight and watertight. We provide Acrylic Sealant in high quality packaging material to prevent it from moisture. Our Acrylic Sealant is free from adulteration and available in market at the most competitive rates.

Grout Hardener

We are among the trusted Manufacturers and Suppliers of Super Bond Waterproofing Adhesive (SPW+101) from Surat, Gujarat. Waterproofing Adhesives are precisely processed at our production house. The product is suitable for performing plasticizing actions and provides cohesiveness and waterproofing to cement concrete, mortar etc. We provide Waterproofing Adhesive in air sealed packaging to keep it free from moisture. Customers can contact us for purchasing Waterproofing Adhesive at market leading rates.   Description : Antique Super Bond - SPW+101 (Add Mixture) is specially formulated additive composed of cement compatible, plastisizing agent, polymers & additives. It is used as a waterproofing additive with an additional benefits of plastisizing action, cohesive mix & waterproofing to cement concrete / mortar / plasters. It improves the workability, compressive strength than control & integral waterproofing properties of cement concrete & plasters after curing.Areas of Application Waterproofing of concrete and sand-cement mortars used in : Waterproofing of concrete and sand-cement mortar used in Basements, Roof slabs and screeds, Water tanks & water retaining structures, External plastering, Bathrooms and balconies, Sumps and drains Features & Benefits : Compatibility - Being a liquid, easily dispersible & compatible with concrete / mortar mixes. Cohesiveness - Makes the concrete/mortar more cohesive in low W/C ratio, hence no bleeding & segregation. Durability - Increases durability, by improving integral waterproofing of concrete. Breathing – It retains the breathing efficiency of concrete. Permeability – It reduces the permeability of water into concrete by blocking the capillaries. Economics – It is an economical additive as compare to other waterproofing materials. Workability – Improves workability of freshly mix cement concrete. Water reduction – W/C reduction is possible upto 8%, which improves the cuing properties of concrete. Strength – Increases the strength of the concrete than control mix. Shrinkage - Reduces shrinkage crack development in plaster & concrete. Method of Application : Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes. Start addition of 75 – 80% mixing water & mix for 2-3 minutes. Antique Super Bond - SPW+101 (Add Mixture) is added as per the recommended dosage into the remaining mixing / gauzing water, then add to concrete mixer & mix for another 2 minutes. Discharge the concrete / plaster for application. Cure the applied mortar or concrete as per good construction practices. Precautions & Limitations : Do not add Antique Super Bond - SPW+101 (Add Mixture) to dry cement & aggregate mix. Maintain water-cement ratio as low as possible (< 0.50). Do not increase the dosage of Antique Super Bond - SPW+101 (Add Mixture) than recommendation.  Dosage : 100ml per 50Kgs bag of cement.Packaging : 1, 5 , 20, 200 litersShelf Life & Storage : Shelf life is 12 months from the date of manufacturing in unopened condition. Store in a cool & dry place. Health & Safety Precautions : Use rubber hand gloves & safety goggles, while using Antique Super Bond - SPW+101 (Add Mixture). In case of contact with skin, wash with plenty of water. Keep out of reach of children’s.