Acrylic Coatings Dealers in Mulund, Mumbai

Perma Floor Coat - WD is a single component liquid material available in selected colors, used for coating concrete floors in heavy duty applications. The product is based on high performance polymers specially developed for heavy traffic applications. Primary Use : Perma Floor Coat - WD is used for coating concrete floors and gang ways in the manufacturing units Perma Floor Coat - WD can be used for coating parking areas in the shopping malls and super market As a contrasting color markings on the walkways and in joggers parks Perma Floor Coat - WD is used for coating swimming pools, fountains, water bodies and water tanks Perma Floor Coat - WD is used for coating Tennis/ Badminton/ Squash Courts Perma Floor Coat - WD is used for renovating and redecorating red oxide cement floors in the residential premises Advantages : Perma Floor Coat - WD is water based and hence not messy like conventional coating materials Perma Floor Coat - WD has a higher PH and hence more compatible with concrete No cleaning solvents are required and can be washed off with water when it is still wet Single component and easily brush applied Can be used on wet surfaces Packing : Perma Floor Coat - WD is supplied in 3Kg., 15Kg. 50Kg Packs

• Shelf Life: 24 Months from Date of Manufacture in Sealed Condition.
• Packaging: 400 Ml Aerosol Spray - 550 Ml Aerosol Spray

High Gloss Fast Drying Flexible Acrylic Conformal CoatingELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.Benefits Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits Prevents sparking and corona discharges Non-conductive and has good dielectric properties Excellent resistance to weak acids & alkalis, water, oils and chemical fumes Easily solderable and very convenient for onsite repair jobs Conforms to requirements of specifications MIL-I-46058C Applications Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.Directions For Use - Bulk Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.Directions For Use - Aerosol Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

Acrylic Polymer Waterproofing Coating, Anti Carbonation Coating