Air Valve Dealers in Andheri, Mumbai

• Media: Air
• Coil Voltage (volt): 12V
• Body Material: Aluminium and Brass
• Internals Material: Aluminium
• Seals Material: Standard Nitrile and Viton
• Voltage Tolerance: AC +/-10%

Valve consists of a body and shut off mechanism inside the body. Body has through axial holes of different diameters over the length. Lower part the hole is 8 mm in dia, the remaining part is of 22 mmin dia. (MOC – SS). The upper part of the body is provided with female thread for securing stem assembly and male thread for fastening the valveon the bottle. From one side and under the body there is a connection with male threads for attaching to the pipe lines. The shut off mechanism consist of valve assembly with a pad made of polyamide resin, stem assembly (MOC - MS), bushing (MOC – Gun Metal), gasket (MOC - Copper), spring (MOC – Case hardened steel) with packing . The stem assembly in its turn has a nut, stem, ball and pivot journal. Hand wheel assembly is fixed by nut on the square end of stem for opening and closing of the valve. The air leakage from the valve is prevented by a seal and made in movable and fixed joint. The movable joint of valve end and bushing are sealed by rubber rings. Valve assemblies have tested for the leak tightness by compressed air at a pressure of 400 kgf/cm² and hydraulic test for strength at a hydraulic pressure of 600 kgf/cm².

the varie av21 can be used..  at top of wet riser of fire fighting systems. at ends of vertical uptake line (top) of hydro- pneumatic systems. in hvac lines wherever air needs to be removed automatically without wasting chilled water into the drain. other applications wherever water (liquid) is present in a pressurized system and air needs to be removed without wasting hot / cold water. in hot water (solar) systems.   salient features   the varie av21 uses a low - density solid plastic float (and not hollow) thus eliminating failure of float. Other conventional air vent valves use a hollow metallic ball float which develops pin holes or leakages from the welding joint and becomes heavy (due to water that enters the float). The valve thus remains in open position permanently. simple design with minimal parts makes it virtually maintenance free. has built-in filter which prevents ingress of dirt & foreign particles, which are the main culprits for choking with malfunction. light weight. transparent chamber in av21-t shows visual indication of water level to determine if valve is malfunctioning. av21-t (transparent) comes with a protecting sun cap to avoid moss / algae formation inside due to sunlight.

The unit is designed to provide a flexible air seal, allowing larger particles to easily pass through the valve while maintaining its air seal. Bolting arrangement on side plate allows service or change-out of the reinforced rubber vane tips without removing the entire unit from the system.Components of a rotary feeder include a rotor shaft, housing, head plates, and packing seals and bearings. Employing Karyasiddhi make rotary airlock   on your dust collection system allows for continuous operation without the need to shut down for barrel removal or lost labor time for barrel change outs. A rotary airlock can also minimize employee exposure to dust while making your system less susceptible to material back-up and damage.   Applications   • Steel Industry Blast Furnace, Electric Arc Furnace, BOF, etc   • Fertilizer Industry Phosphate Rock Dryers & Calciners, Dryers   • Non-Ferrous Copper Reverberatory Furnace, Laea Blast Furnace   • Pulp & Paper Lime Kilns, Back Liquor Recovery, Bark Boilers   • Sugar Industry Boiler Flue Gas, Bagging Section   • Mineral Products Asphalt Stone Dryers, Cement Kilns   • Pharmaceuticals Tablet Coating Fans, etc  

Application: For use when an air pilot signal is required at a set hydraulic pressure. Can be used to shift valves, and start or stop pneumatic pumps. Attaches directly to control manifold or can be mounted “in-line” to read system hydraulic pressure. Automatically turns on an air pilot signal when a predetermined system pressure is reached. Has 1/4" NPTF male thread and 1/4" NPTF fitting for gauge mounting if required. Adjustable from 500-10,000 psi. Maximum rating of 25 scfm at 100 psi.  

• Weight: 0-500 g
• Material: Mild Iron, Fibre, Plastic, Stainless Steel
• Usage: Water, Air
• Colour: Black, White, Silver, Blue
• Size: 0-1000 MM, 1000-2000 MM
• Size: 0-10 Inch, 10-20 Inch

• Brand Name: None
• Single gross weight: 0.4 kg
• Delivery Time: 7 Days For Normal Quantity
• Place of Origin: Shanghai, China (Mainland)
• Packaging: Paper Box & Plastic Bag
• Quality Control: Defective Rate <1.0%
• Single package size  : 16X7X5.5 cm

Also known as Auto diaphragm valves - Pneumatically operated diaphragm actuators can be direct, reverse or double acting in operation with spring or can be springless. Springless actuator can be supplied with the air reservoir for fail safe position. Effective area 9 sq. in. to 300 sq. in. and in case of double , diaphragm actuators. it can go up to 600 sq.in.to match any thrust requirements.

We provide our clients with a world-class range of Rotary Air Lock Valves, which can be put to use as a discharger, pneumatic feeder and batch feeder. These valves are made using quality material, which makes these all the more durable. Our clients can avail these valves at an affordable price.

Air Admittance Valve, Special Cement, drain covers, Frp Manhole Covers

We provide you to its world of air valves.

VALVES FOR AIR, STEAM, Pneumatic Cylinders, PNEUMATIC CYLINDERS VALVES