Bagadia Petrochem Andheri East, Mumbai, Maharashtra

DESCRIPTION SABIC® PP 5706P is specially developed for producing rigid injection molded articles for general purpose applications. It gives consistent processability and high gloss at the products. TYPICAL APPLICATIONS SABIC® PP 5706P can be used for houseware articles, food containers, furniture and toys.   PROCESSING CONDITIONS Typical processing conditions for 5706P are: Barrel temperature range: 200 - 250°C. Mold Shrinkage: 1.2 - 2.5% depending on wall thickness and processing conditions. Mold Temperature: Normally 15 - 40°C, up to 65°C for thick parts STORAGE AND HANDLING Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.    

Color : White

Form : Granules

Application : Injection Molding, Industrial

Type : Polypropylene Granules

Country of Origin : India

These are film grades and can be processed easily on conventional blown film lines. J1020FS20 has been blended with necessary additives during manufacture to obtain good surface slip and easy open-ability. J1020FA20 is manufactured without any additive to facilitate adhesion during lamination. APPLICATIONS: Slip grade for Mono & Co-extruded film / Cast film, liner film and non-slip grade for adhesive lamination, hygiene & air bubble film. Typical Process Conditions: Melt Temperature (˚C) - 160 – 200 Recommended Blow Up Ratio (BUR): 1.5 – 3.0 (Based on applications, best results achieved with BUR of 2.5 : 1) Die Gap – > 0.8 mm (Based on film thickness and throughput of the machine) Regulatory Information Meets the requirements stipulated in standard IS: 10146 on "Specification for Polyethylene for safe use in contact with foodstuffs, pharmaceuticals, and drinking water". It also conforms to IS 16738:2018 “Positive List of Constituents for Polypropylene, Polyethylene and their Copolymers for its Safe Use in Contact with Foodstuffs and Pharmaceuticals” The grade and the additives incorporated in it also comply with the FDA: CFR Title 21,177.1520, Olefin polymers. Storage Recommendations Bags should be stored in dry/closed conditions at temperatures below 50°C and protected from UV / direct sunlight

Material : Plastic

Color : Natural White

Application : Industrial Use

Country of Origin : India

DESCRIPTION SABIC® PP 37MK10 is a impact copolymer polypropylene resin and is typically used for industrial injection molding application. Molded parts made from this resin typically exhibits good impact, high stiffness and good heat stability. This product is formulated with nucleating agent.   TYPICAL APPLICATIONS SABIC® PP 37MK10 can be used to produceCrates, electrical appliances, thin wall applications and industrial applications   PROCESSING CONDITIONS Typical Processing conditions for 37MK10 are: Recommended melt temperature : 190 – 230 °C   STORAGE AND HANDLING Polypropylene resin should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably do not exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PP resin within 6 months after delivery.    

Material : PPCP

Color : White

Form : Granules

Application : Injection Moulding

Packaging Type : Plastic Bag

Country of Origin : India

PRODUCT DESCRIPTION HDPE B1054 is high density polyethylene specially developed for large blow molding and jerry cans. The material offers high stiffness, good processability and excellent combination of stiffness/ESCR.   TYPICAL APPLICATIONS B1054 is specially designed for Standard jerry cans, Light weight jerry cans and UN approved jerry cans. The grade is intended for use in food contact application.   FOOD REGULATION B1054 is suitable for Food contact application. Detailed information is provided in relevant Material Safety Datasheet and for additional specific: information please contact SABIC local representative for certificate   STORAGE AND HANDLING Polyethylene material should be stored in a manner to prevent a direct exposure to sunlight and/or heat. The storage area should also be dry and preferably don't exceed 50°C. SABIC would not give warranty to bad storage conditions which may lead to quality deterioration such as color change, bad smell and inadequate product performance. It is advisable to process PE resin within 6 months after delivery.

Color : White

Application : Blow Moulding

Type : HDPE

Country of Origin : India

Shape : Different shape available

Product Description Moplen EP332L is a heterophasic copolymer with medium flow used in injection molding. This grade is characterized by a medium stiffness-impact balance at low temperature as well as a low warpage tendency. The additive formulation provides a good heat aging resistance. Moplen EP332L is typically used by customers requiring a high resistance to temperature degradation, in particular for battery cases and automotive components.   This grade is not intended for medical and pharmaceutical applications. Status Commercial: Active Availability Africa-Middle East; Asia-Pacific; Australia and New Zealand; Europe; South & Central America Application Battery Cases Market Automotive; Consumer Products; Industrial, Building & Construction Processing Method Injection Molding Attribute Good Heat Aging Resistance; Good Impact Resistance; Good Stiffness; Heat Stabilized; Impact Copolymer; Low Warpage   Health and Safety The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact you ocal representative. Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes. Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed.

Material : PPCP

Color : White

Form : Granules

Application : Injection Moulding

Packaging Type : Plastic Bag

Type : Ppcp Granules

Country of Origin : India

Description DFDC-7080 is a butene LLDPE grade offering excellent drawdown and puncture resistance combined with high gloss and clarity. Films made from DFDC-7080 resin have very good tensile and toughness properties. Additives: • Anti-block: High • Slip: Medium • Thermal Stabilizer   Application Agricultural Film, bag in box, food packaging films, FFS packaging films, garment bags, liner bags, multi-layer packaging films, cast film, drip irrigation tubes Storage and Handling Luban DFDC-7080 must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material. Safety Luban DFDC-7080 is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet. Food Contact Luban DFDC-7080 meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration”. Recycling The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

Material : Lldpe

Color : White

Form : Granules

Type : Lldpe Granule

Apparence : Granules

Country of Origin : India

DESCRIPTION EMDA-6200 grade is a high-density polyethylene copolymer resin designed for blow molding small to medium size bottles. It can be used on intermittent as well as continuous blow molding machines for high-speed production of high quality bottles. The bottles have excellent environmental stress cracking resistance and a good balance of rigidity and impact strength. They are easily trimmed and exhibit excellent surface attributes. APPLICATIONS EMDA-6200 is intended for producing containers of up to 10 liter capacity for packaging household and industrial chemicals (detergents, bleach, fabric softeners, etc.) toiletries, cosmetics and food products. It is als suitable for producing thin-walled parts and household items In addition EMDA-6200 can also be used successfully for extruding sheets and profiles including corrugated drainage Pipes.   FOOD CONTACT USAGE EMDA-6200 can be used for all food contact applications including holding food during cooking. It conforms to US FDA Regulation 21 CFR 177.1520 as well as EC Directive 90/128/EEC and its amendments to-date. Food contact suitability certificate is available upon request.   AVAILABILITY EMDA-6200 is supplied in 25-Kg bags in secured pallets of 55 bags (1.375 MT net). It is also supplied in sea bulk containers of up to 15 MT capacity.   STORAGE AND HANDLING EMDA-6200 is supplied in pellet form and is readily conveyed on conventional polyethylene bulk handing equipment. The bulk handling system should be designed to prevent accumulation of fines and dust particles that can pose an explosion hazard. Ensure all equipment is properly grounded. The product should be stored in a cool dry shaded area away from dust, sunlight and heat. For more details on storage and handling see our Polyethylene Storage and Handling Guide. Also carefully review the Material Safety Data Sheet supplied with this product for health, safety and waste considerations.   IMPORTANT NOTICE The information supplied in this bulletin to the best of our knowledge is accurate and factual as of the date printed. It is offered solely as a convenience to EQUATE’s customers and is intended only as a guide for EMDA-6200. Since the user’s specific applications and conditions of use are beyond EQUATE’s control, EQUATE makes no warranty or representation regarding results that may be obtained by the user. It shall be theresponsibility of the user to determine the suitability of the product for the user’s specific application. The information disclosed in this document is not to be construed as a recommendation to use the product in infringement of any patent rights covering the usage.

Material : Hdpe Plastic

Packaging Type : Plastic Bag

Country of Origin : India

Application : closed head shipping containers of up to 50 liter size, fuel tanks, drums, jerry cans.

Material : Lldpe

Color : White

Form : Granules

Country of Origin : India

DESCRIPTION Borstar® RA140E is a BNT Nucleated high molecular weight, low melt flow rate polypropylene random copolymer (PP-R) natural colored. APPLICATIONS Borstar® RA140E together with the appropriate additive package is recommended for the production of PP-R pipes and fittings used in: Heating, Plumbing, Domestic water, Relining, and Industrial applications SPECIFICATIONS Borstar® RA140E is intended to fulfill the following standards and regulations, providing the appropriate industrial manufacturing standard procedures are used and a continuous quality system is implemented: DIN 8078, DIN 8077 and EN ISO 15874   SPECIAL FEATURES Borstar® RA140E is a natural grade used for production of pipes and fittings. The material is in pellet form and includes selected additive package which ensure: Enhanced process ability High temperature resistance Economical pipe production Low incidence on taste and odour Excellent product consistency Good impact strength The pipe systems will show high durability, no corrosion, good weldability, homogeneous joints, low tendency to incrustations and fast and easy installation   STORAGE Borstar® RA140E should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on physical properties of this product   SAFETY The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.   RECYCLING The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling    

Material : Polypropylene

Color : White

Feature : Good Quality

Type : Random

Country of Origin : India

DESCRIPTION FT6230 is a Low Density Polyethylene for Film extrusion produced by high pressure Tubular Technology. This grade is developed for the production of packaging film with good optical properties. FT6230 contains no additives. PROCESSING GUIDELINES FT6230 can be processed easily on most types of blown film equipment such as LDPE, LLDPE or HDPE extruders Recommended processing conditions: Melt temperature 160 –190°C Die gap > 1.0 mm FLH: > 2 DD BUR: > 2:1   FOOD CONTACT REGULATIONS FT6230 fulfils the food contact regulations in most countries. If required, contact your Borouge representative for a certificate. STORAGE The product should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet for this product   SAFETY The product is not classified as a hazardous mixture. Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required A Safety Information Sheet is available on request. Please contact your Borouge representative for more details on various aspects of safety, recovery and disposal of the product.   RECYCLING The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.  

Color : White

Application : Industrial Use, Plastic Industry

Technics : Machine Made

Packaging Size : As Per Client Requirement

Country of Origin : India

DESCRIPTION FT5230 is a Low Density Polyethylene for Film extrusion produced by high pressure Tubular technology This grade is developed for the production of packaging film with good optical properties for shrink wraps and medium duty film applications. FT5230 contains no additives.   PROCESSING GUIDELINES FT5230 can be processed easily on most types of blown film equipment such as LDPE, LLDPE or HDPE extruders. Recommended processing conditions: Melt temperature 160 –190°C Die gap > 1.0 mm FLH: > 2 DD BUR: > 2:1 FOOD CONTACT REGULATIONS FT5230 fulfils the food contact regulations in most countries. If required, contact your Borouge representative for a certificate. STORAGE The product should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.    

Material : Plastic

Texture : Highly Soft

Color : Natural White

Form : Granuels

Application : Industrial Use

Country of Origin : India

Description Luban polypropylene is manufactured using Novolen vertical stirred Gas-phase polymerization process. Luban HP4128N is a homopolymer polypropylene with superior slip and anti-blocking properties. Application Tubular quench (TQPP) and Cast film, flexible packaging including textiles over raps, garment bags, snack food packaging and straws.   Processing Guidlines L/D ratio 24.1 – 30.1 Compression ratio 3.1 – 4.1 Melt Temperature  200 – 250 ° C Pellets Drying    Not essential but helps in insuring consistent feed to extruder   Storage and Handling Luban HP4128N must be protected from direct sunlight and should be stored in a shaded and completely dry area. During handling and processing, the material should be kept in a well-ventilated area to prevent the accumulation of dust and fumes. Contact with strong oxidizers, excessive heat, sparks or open flame should be avoided as this could initiate the degradation process and consequently impact the quality of the material.   Safety Luban HP4128N is not classified as dangerous preparation. For further information about safety in handling and processing please refer to the Safety Data Sheet. Food Contact Luban HP4128N meets the requirements of the U.S. Food and Drug Administration (FDA) as specified in 21 CFR 177.1520, covering safe use of polyolefin articles and components of articles intended for direct food contact. For additional information on approved conditions of use for food contact applications, please refer to the “Product Stewardship Declaration   Recycling The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

Application : Industrial

Type : Polypropylene Granules

Country of Origin : India

Repol H050MN is recommended for injection molding and sheet extrusion. It is an ideal choice as a compounding base and as a blending material in furniture compounds. It is also suitable for molding rigid containers, houseware and thermoware. Repol H050MN contains nucleating agent for high rigidity and reduced cycle time. It also contains antistatic agent that reduces static charge build up on products. Typical Processing Conditions Melt temperature: 220 – 260 OC Mold temperature: 20 – 50 OC Note: Processing parameters mentioned above are for reference only and not to be considered as specifications. They may vary based on the product to be manufactured.   Applications Furniture and rigid packaging.   Regulatory Information The product complies with Indian Standard IS 10910 on “Specification for polypropylene and its copolymers for safe use in contact with foodstuffs, pharmaceuticals and drinking water. It also conforms to IS 16738:2018 on positive list of constituents for polypropylene, polyethylene and their copolymers for its safe use in contact with foodstuffs and pharmaceuticals. The grade and the additives incorporated in it also comply with the FDA:CFR Title 21,177.1520, Olefin polymers   Storage Recommendations Bags should be stored in dry / closed conditions at temperatures below 50°C and protected from UV / direct sunlight

Material : Plastic

Color : White

Form : Granules

Uses : Manufacturing Units

Thickness : 10-20mm

Country of Origin : India

Material : Plastic

Color : Natural White

Form : Granules

Application : Industrial Use

Plastic Type : PP

Transparency : Clear

DESCRIPTION EGDA-6888 is a high molecular weight, high density polyethylene copolymer that has been designed specifically for tubular film extrusion. Its broad molecular weight distribution and density have been optimized to give excellent bubble stability at high extrusion rates with high film strength and rigidity. The combination of high strength and excellent drawdown-ability makes EGDA-6888 ideal for down gauging in many applications. APPLICATIONS Tubular films produced from EGDA-6888 are recommended for high strength grocery sacks, shopping bags, produce bags and high quality thin films for multiwall sack liners and replacements for thin paper products. EGDA-6888 is also suitable for making non-pressure “gravity” pipes for drainage and sewage applications. Film properties are typical of blown films extruded at a 4:1 blow-up ratio and melt temperature of 215 C. ASTM: American Society for Testing and Materials   EXTRUSION CONDITIONS EGDA-6888 can be extruded on conventional HDPE blown film equipment at 215C melt temperature. A flat or moderately increasing temperature profile is recommended for its extrusion. A 4:1 blow-up ratio and high stalk bubble configuration are always recommended for products requiring high strength. Lower blow-up ratios (3:1) can be used for products that do not require high strength. For best gauge uniformity, a minimum extrusion rate of 0.14 kgs/hr/mm of die circumference is recommended. The best balance of extrudability and film strength is obtained with a 1.0 to 1.1 mm die gap.   FOOD CONTACT USAGE EGDA-6888 can be used for all food contact applications including holding food during cooking. It conforms to US FDA Regulation 21 CFR 177.1520 as well as EC Directive 90/128/EEC and its amendments to-date. Food contact suitability certificate is available upon request.   AVAILABILITY EGDA-6888 is supplied in 25 Kg bags in secured pallets of 55 bags (1.375 MT net). It is also supplied in sea bulk container of up to 20 MT.   STORAGE AND HANDLING EGDA-6888 is supplied in pellet form and is readily conveyed on conventional polyethylene bulk handing equipment. The bulk handling system should be designed to prevent accumulation of fines and dust particles that can pose an explosion hazard. Ensure all equipment is properly grounded. The product should be stored in a cool dry shaded area away from dust, sunlight and heat. For more details on storage and handling see our Polyethylene Storage and Handling Guide. Also carefully review the Material Safety Data Sheet supplied with this product for health, safety and waste considerations.   IMPORTANT NOTICE The information supplied in this bulletin to the best of our knowledge is accurate and factual as of the date printed. It is offered solely as a convenience to EQUATE’s customers and is intended only as a guide for EGDA-6888. Since the user’s specific applications and conditions of use are beyond EQUATE’s control, EQUATE makes no warranty or representation regarding results that may be obtained by the user. It shall be the responsibility of the user to determine the suitability of the product for the user’s specific application. The information disclosed in this document is not to be construed as a recommendation to use the product in infringement of any patent rights covering the usage.

Color : White

Grade : Extrusion Grade

Type : HDPE

Country of Origin : India

DESCRIPTION RE425MO is a versatile designed transparent polypropylene random copolymer with medium melt flow rate intended for injection moulding and injection stretch blow moulding. RE425MO is suitable for high speed injection moulding with excellent clarifier and demoulding properties. Articles produced from this product have excellent transparency, excellent impact strength at ambient and refrigerator temperatures, good organoleptic properties, low blooming, good denesting performance and excellent hinge properties   APPLICATIONS Lids Food storage containers Houseware containers Sports and drinking bottles Customized / hinged closures Transparent pails SPECIAL FEATURES Excellent impact performance Low blooming Very good gloss and transparency Excellent hinge properties PROCESSING CONDITIONS RE425MO is easy to process with standard injection moulding -and injection stress blow moulding machines. Following parameters should be used as guidelines: Melt temperature: 220 - 260°C Holding pressure: 200 - 500bar Mould temperature: 30 - 40°C Injection speed: High Shrinkage 1 - 2%, depending on wall thickness and moulding parameters   STORAGE RE425MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product.   SAFETY The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.

Color : White

Application : Injection Moulding

Feature : Good Quality,Long Shelf Life

Type : Natural PP Granules

Country of Origin : India

DESCRIPTION RE420MO is a versatile designed transparent polypropylene random ethylene copolymer with medium melt flow rate intended for injection moulding and injection stretch blow moulding RE420MO is suitable for high speed injection moulding due to clarification and excellent demoulding properties. Articles originating from this product have excellent transparency, good organoleptic properties, good balance of stiffness and impact strength at ambient and refrigerator temperatures, low blooming, good denesting performance and excellent hinge properties.   APPLICATIONS Lids Transparent pails Customized / hinged closures Food storage containers Sports and drinking bottles Houseware containers   SPECIAL FEATURES Very good stiffness and impact balance Good gloss and transparency Low blooming Excellent hinge properties   PROCESSING TECHNIQUES RE420MO is easy to process with standard injection moulding machines and injection stretch blow moulding machines. Following parameters should be used as guidelines: Melt temperature 220 - 260 °C Holding pressure 200 - 500 bar Mould temperature 30 - 40 °C Injection speed High Shrinkage 1 - 2 %, depending on wall thickness and moulding parameters

Material : Polypropylene, Polypropylene

Color : White

Type : Random

Country of Origin : India

Description Borstar®HE1490 is a Black, bimodal HDPE product produced using the proprietary Borstar® bimodal technology which offers excellent melt strength and process ability for sprinkler pipe extrusion and drip lateral with superior mechanical properties. CAS-No. 25087-34-7 APPLICATIONS HE1440 is recommended for Range of wall thickness for drip irrigation tubing for online drip lateral and flat as well as cylindrical emitting pipe/inline production Sprinkler Irrigation pipes Non pressure utility pipes   KEY FEATURES HE1440 offers excellent balance of process-ability and mechanical properties   PROCESSING CONDITIONS The actual extrusion conditions will depend on type of equipment used and the size and wall thickness of the pipe required. Following conditions should be used as a guide for the starting up the extruder. Barrel Zone 180 – 210 Deg C Die Zone 190 – 210 Deg C Please contact your local Borouge representative for specific recommendation for the processing conditions.   STORAGE This product should be stored in dry conditions at temperature bellow 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and can have negative effects on physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product.   SAFETY The product is not classified as a hazardous mixture. Dust and fines from the product carry a risk of dust explosion. All equipment should be properly earthed. Inhalation of dust should be avoided as it may cause irritation of the respiratory system. Small amounts of fumes are generated during processing of the product. Proper ventilation is therefore required. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative. RECYCLING The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.

Material : HDPE

Shape : Granuales

Color : White

Application : Industrial Use

Packaging Type : BOPP Bags

Country of Origin : India

DESCRIPTION HE125MO is a versatile polypropylene homopolymer intended for injection moulding. This product shows very good stiffness and toughness. APPLICATIONS Closures Houseware Garden furniture Compounds and master batches SPECIAL FEATURES Good flow behaviour High stiffness   PROCESSING CONDITIONS HE125MO is easy to process with standard injection moulding machines. Following parameters should be used as guidelines: Melt temperature: 220 - 260°C Holding pressure: 200 - 500bar As required to avoid sink marks Mould temperature: 20 - 40°C Injection speed: High Shrinkage 1 - 2%, depending on wall thickness and moulding parameters STORAGE HE125MO should be stored in dry conditions at temperatures below 50°C and protected from UV-light. Improper storage can initiate degradation, which results in odour generation and colour changes and can have negative effects on the physical properties of this product. More information on storage can be found in Safety Information Sheet (SIS) for this product   SAFETY The product is not classified as a hazardous preparation. Please see our Safety Information Sheet (SIS) for details on various aspects of safety, recovery and disposal of the product, for more information contact your Borouge representative.   RECYCLING The product is suitable for recycling using modern methods of shredding and cleaning. In-house production waste should be kept clean to facilitate direct recycling.   RELATED DOCUMENTS The following related documents are available on request, and represent various aspects on the usability, safety, recovery and disposal of the product. Safety Information Sheet Statement on chemicals, regulations and standards Statement on compliance to food contact regulations

Color : White

Form : Granules

Application : Industrial

Type : Polypropylene Granules

Country of Origin : India

Product Description Lupolen 2427 K is an additivated, low density polyethylene. It contains an antioxidant, slip and anti-blocking agent. It is characterized by a good processability. Films made from Lupolen 2427 K exhibit good optical properties. It is delivered in pellet form. This product is not intended for use in medical and pharmaceutical applications. Status Commercial: Active Availability Africa-Middle East; Asia-Pacific; Europe Application  Food Packaging Film; Hygiene Film; Shrink Film Market   Flexible Packaging Processing Method  Blown Film; Cast Film Attribute  Antioxidant; Good Heat Seal; Good Optical Properties; Good Processability; Low Friction; Unspecified Antiblocking; Unspecified Slip   Health and Safety The resin is manufactured to the highest standards, but special requirements apply to certain applications such as food end-use contact and direct medical use. For specific information on regulatory compliance contact your local representative. Workers should be protected from the possibility of skin or eye contact with molten polymer. Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to the eyes. Molten polymer may be degraded if it is exposed to air during any of the processing and off-line operations. The products of degradation may have an unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes or vapours. Legislation on the control of emissions and pollution prevention should be observed. The resin will burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. While burning, the resin contributes high heat and may generate a dense black smoke. Recycled resins may have previously been used as packaging for, or may have otherwise been in contact with, hazardous goods. Converters are responsible for taking all necessary precautions to ensure that recycled resins are safe for continued use. For further information about safety in handling and processing please refer to the Safety Data Sheet

Material : Low Density

Shape : Rectangular

Color : White

Pattern : Plain

Type : Low Density Polyethylene

Country of Origin : India