Ceramic Heaters Dealers in Andheri, Mumbai

Ceramic Jacketed Heaters are EXCEL’s premium product since three decades Especially to heat the cylinders (barrels) on all types of plastic (s) processing machinery The key to the ceramic – jacketed heaters is its superior design to save power Outer insulation jacket conserves energy Up to 20% of power consumption reduced Maximum watt density = 50 Watts/square inches Note: In case where high watt densities are required, it is important that all heaters should be used with appropriate, approved and precise temperature control/sensor device(s) Maximum sheath temperature up to 800˚ C Use of special ceramic material “steatite” with high thermal conductivity The model is designed & constructed with special effective dual insulation which reduces the rate of heat radiation/loss, resulting swift rise in the temperatures of the object to be heated Uniform heat distribution throughout the barrel Reduction of thermal shocks on polymer melt, resulting in improved quality Good shine of your finished products Increases productivity Ceramic Jacketed heaters meet progressive requirements of the plastic processors

  Ceramic Flexible Heaters are manufactured from high grade materials and have a working temperature capability of 1050°C. They can be powered from Power source/Heat Treatment units or Welding machines.Heating element consists of multi strand Nickel Chrome element wire, electrically insulated by interlocking sintered alumina beads, providing a flexible high heat transfer-Mat, complete with twistlock connectors.Heaters are rated at low voltage of 30V, 32.5V, 40V, 42.5V, 60V, 65V, 80V and 85V., and available in wide range of sizes. Non-standard voltages of 220V & 240V are also available. Other sizes and rating can be supplied on request.Heaters are rated at 45Amps for 30V, 60V and 80V and 50 Amps for 32.5V, 65V and 85V.

We are recognized as one of the trusted Ceramic Band Heater Manufacturers, Exporters and Suppliers from Mumbai (Maharashtra). The Ceramic Band Heaters design consists of a helically wound resistance coil made from 80/20 nichrome wire, evenly stretched and precisely strung through a specially designed ceramic insulating bricks forming a flexible heating mat and its exterior part is coated with stainless steel sheet. Thanks to high conductive ceramic, long service life, fast and simultaneous dispersion of heat is realized by installing chrome-nickel wire properly. Thanks to conservation of heat achieved by ceramic fibres conservation of energy up to 25% to 45% can be obtained. Glass fibre cable and armoured cable whose exterior surface is coated with stainless steel upon request these heaters can be manufactured in special dimensions and values. SpecificationsElectricalResistance + 10% -5%Wattage + 5% -10%Voltage 220V AC to 480V ACMaximum Watt 50 watts / sq. inch.Maximum Temp.800o CDimensionalMinimum Dia. 38 mmMinimum Width 25 mmOverall Thickness12-15 mmWidth - Normal Multiple of 15 + 6mmStd. gap between edges 5 to 10 mm

We are offering ceramic band heaters. Description: php's ceramic band heaters are designed and manufactured with more than 40 years of practical experience, for superior performance and life expectancy. As a manufacturer specialized in industrial electric heating elements & the desire to provide quality products and services to our customers both oem's & end users, php specializes in designing ceramic band heaters , mica band heaters, nozzle heaters & strip heaters to your exact specifications. Depending upon applications php ceramic band heaters are manufactured with high temperature oxidation metal sheath and high grade steatite insulators to withstand high temperatures. A superior grade nicr resistance wire coil provides uniform and reliable heat distribution with the best combination of physical strength, high emissivity & good thermal conductivity to heat cylindrical parts, good for sheath temperature up to 5000c. Php ceramic band heaters are also available with various construction styles with special inbuilt energy saving options. features: 1. available in chrome nickel steel with power saving options. 2. special high grade steatite insulators for superior thermal conductivity. 3. power saving up to 30%. 4. designed for higher temperature up to 500°c. 5. robust terminal junction with specially designed protection cap. 6. efficient heat transfer even on irregular surfaces in comparison to mica band. 7. conserves energy with improved heating efficiency up to 55 watts per square inch. 8. engineered for longer life with superior quality nichrome wire for uniform temperature & maximum amperage carrying capacity. 9. reduces down time for replacements. 10. easy installation and removal. 11. available in various lead terminations & clampings expandable to fit around the barrel o.d. applications: 1. injection moulding. 2. film extruders. 3. blow moulding. 4. plastic & rubber processing machinery. 5. laboratory equipment 3 construction styles: 1. Premium-heat construction standard features for premium-heat construction suggested watt density 35 to 40 wattssq. Inch chrome nickel steel sheathing with 4mm thick heat saving thermal insulation single piece construction 500 mm long insulated metal braided flexible leads. barrel nut type clamping with terminal protection box. total wall thickness 12mm min requirement : i.d. 60mm, width 35mm also available in two piece construction. 2. Power saver construction standard features for power saver construction suggested watt density 40 to 45 watts sq inch. chrome nickel steel sheathed with 16mm thick twin insulated cover single piece construction. 500 mm long insulated metal braided flexible leads allen key barrel nut type clamping with terminal protection box. total wall thickness: 25 mm. also available in two piece construction. min requirement : dia. 75mm, width 75mm 3. Power saver plus construction standard features for power saver plus construction suggested watt density 50 to 55 watts sq inch. chrome nickel steel sheathed with heat optimizing insulated cover. single piece construction. 500 mm long insulated metal braided flexible leads barrel nut type clamping with terminal protection box. total wall thickness : 45mm min requirement: i.d.: 100mm, width 100mm. also available in two piece construction. electrical variations: single phase: php's band heaters are usually designed on 230 volts single phase unless specified. dual phase: ceramic band heaters can be designed with multiple circuits to operate in single or three-phase circuits. three phase: on very high wattage band heaters it would be advantageous to install three-phase wiring to reduce the current load across a single conductor. Three-phase wiring is available with all types of insulation, construction styles, and clamping variations. limitations: minimum width: 3"(76.2mm).

We offer high end Ceramic Band Heaters to our esteemed clients. The Ceramic Band Heaters employ an exclusive method of designing, which maximizes the element wire coverage of the heated area. In addition, the Ceramic Band Heaters have been fabricated from the best quality raw material, using sophisticated technology. Avail the Ceramic Band Heaters from us at nominal prices.

Vinman's Ceramic Band Heaters are designed and manufactured with more than 25 years of practical experience, for superior performance and life expectancy. As a manufacturer specialized in industrial electric heating elements & the desire to provide quality products and services to our customers both OEM's & End Users, Vinman specializes in designing Ceramic Band Heaters , Mica Band Heaters, Nozzle Heaters & Strip Heaters to your exact specifications. Depending upon applications Vinman's Ceramic Band Heaters are manufactured with high temperature oxidation metal sheath and high grade steatite insulators to withstand high temperatures. A superior grade NiCr resistance wire coil provides uniform and reliable heat distribution with the best combination of physical strength, high emissivity & good thermal conductivity to heat cylindrical parts, good for sheath temperature up to 5000C. Ceramic Band Heaters are also available with various construction styles with special inbuilt Energy saving options. Features: 1. Available in Chrome Nickel Steel with Power Saving Options. 2. Special High Grade Steatite Insulators for Superior Thermal Conductivity. 3. Power saving up to 30%. 4. Designed for Higher Temperature up to 500°C. 5. Robust Terminal Junction with Specially Designed Protection Cap. 6. Efficient Heat Transfer even on irregular surfaces in comparison to Mica Band. 7. Conserves Energy with Improved Heating Efficiency up to 55 Watts per square inch. 8. Engineered for Longer life with Superior quality Nichrome wire for Uniform Temperature & Maximum Amperage carrying capacity. 9. Reduces Down time for replacements. 10. Easy installation and removal. 11. Available in various Lead Terminations & Clampings expandable to fit around the Barrel O.D. Applications: 1. Injection Moulding. 2. Film extruders. 3. Blow Moulding. 4. Plastic & Rubber Processing Machinery. 5. Laboratory Equipment 3 Construction Styles: 1. Premium-Heat Construction 2. Power Saver Construction 3. Power Saver PLUS Construction Electrical Variations: Single Phase: Vinman's band heaters are usually designed on 230 Volts single phase unless specified. Dual Phase: Ceramic Band Heaters can be designed with multiple circuits to operate in single or three-phase circuits. Three Phase: On very high wattage band heaters it would be advantageous to install three-phase wiring to reduce the current load across a single conductor. Three-Phase wiring is available with all types of insulation, Construction styles, and clamping variations. Limitations: Minimum width: 3"(76.2mm).

Ceramic Band Heater, Mica Band Heater, Mica Strip Heater, mica barrel heater

Ceramic Heater, Cabinet Dryer Tray Oven, Sulthises Crucible

Ceramic IR Heaters, glass heaters, Lead Bonded Heaters, Micro Tubular Heater