Colloid Mill Dealers in Marol, Mumbai

Product is fed into hopper and specially designed feeding device push the material to stator and rotor for high shearing, cutting and rubbing forces. Due to conical arrangement, the slightly deviating tapeiring of the milling surface of the stator and rotor, the angular gap becomes narrower towards the discharge section and the centrifugal effect of the rotor rotates at a high speed, the material is then forced into next tooth stage. The tooth breaks the particles with high degree of forces. Intence whirling multiples the grinding and mixing effect. The processed material continuously leave the mill through the drain pipedischarge spout, if required it can be recirculated.

MEVISH Colloid Mill is suitable for Homogenising, Emulsifying, Dispersing, Mixing, Comminuting of liquids to highly viscous products. It is based on rotor- stator principle. It is available in plain as well as Water Jacketed model which is suitable for heat sensitive products. Flame proof electrical can be supplied on demand at extra cost. .   Colloid Mill is based on Rotor and stator principle, as you decrease the gap between Rotor and Stator you can get fine product.Colloid Mill Machine is a machine used in the disintegration of solid particles or droplet size of a liquid present in suspension or emulsion. The Colloid Mill Machine consists an inlet (which is subjected to a tremendous shearing action that effects a time dispersion of uniform size) and an outlet. Colloid mill works on the rotor-stator principle.

• Motor: 3 HP, 2800 RPM
• Hopper Capacity: 15 Ltrs
• Final Particle Size: 10-15 Microns

It works on the rotor stator principle. The complete assembly is provided with serrations for better mixing. Better mixing can also be obtained by adjusting the gap between the rotor and the stator by the handle provided. The product is subjected to a high shear action in the rotor stator assembly due to which the particle reduction takes place. The material is then pushed out through the outlet for further process or for recirculation. The mill is optionally provided with a cooling water jacket and a mechanical seal for leak proof operation. Granulation Line:- Colloid Mills is suitable for homogenizing, mixing, emulsification, dispersion of liquids, ointment, creams, and other similar difficult to mix products. mill is optionally provided with a cooling water jacket and a mechanical seal for leak proof operation.

SPECIAL FEATURES * All contact parts are made out of SS304 SS316 SS316 L quality material. * Coupling provided between motor shaft and rotor for the ease in maintenance. * 3 way valve system for draining and re-circulation of liquids or discharge spout for viscous products can be provided. * Contact parts can be easily dismantled for cleaning. * Flame proof construction provided if customer requires. * Jacketed model with jacket to the hopper.

• Material: Stainless Steel
• Brand Name: ACE
• Voltage: 240 Volt
• Phase: Single Phase
• Capacity: 12 to 100 Kg/Hour
• Speed: 2850 rpm
• Height: 1100 mm
• Motor Power: 3 HP
• Power Source: Electric
• Features: Longer functional life, Sturdy construction, Low maintenance

• Power: 5 hp to 3 hp
• Material: Casting
• Application: Pharmaceutical industry. Food, flour, dairy, sweetmeats and confectionery industry.Chemical industry.Paint industry. Textile industry. Cosmetic and detergent industry. Cubber industry.
• Capacity: 40 kg to 500 kg

• Power: 1 kW
• Material: Stainless Steel
• Brand Name: PCM
• Country of Origin: Made in India
• Voltage: 220 V
• Frequency: 60 Hz
• Phase: Three Phase
• Capacity: 100 Litre/hour
• Speed: 2800 RPM
• Driven Source: Electric
• Reduction Up To: 5 Micron
• Finishing Type: Mirror Finished
• Usage/Application: Industrial

• Model: RDCM3
• Output: 120 to 12000 kgs/shift
• Particle size reduction: 5 to 10 Micron
• Hopper Capacity: 15 ltrs.
• Reduction upto: 5 to 10 microns (Particle Size)
• Electricals: 3 HP/ 2800 RPM / 3 PHASE

Operation Product is fed to the operating area of rotor, having a speed of 3000 rpm by specially designed feed device. The product is processed by high shear, pressures & friction between the stator & rotor, & is also subjected to intensive vibration which exerts their force on it by means of pressing & releasing actions. due to the slightly deviating tapering of the milling surfaces of stator & rotor, the angular gap becomes narrower towards the discharge section. This processed product continuously leaves the mill through the drain pipe, if required, it can be recirculated.   Salient Features All contact parts are made out of SS. 304 (SS.316 on demand at extra charges). No casting are used for avoiding contamination problems. Coupling provided between motor shaft & rotor shaft for ease in maintenance. Three oil seals between the Motor & the processing chamber to prevent liquid going in the motor winding, Resulting in the burning of the motor. Modified design of semi concave teeth in rotor & stator reduces the motor HP & gives better performance in size reduction without damaging the product. Extended bearing housing specially designed to facilitate fine adjustment of bearing clearances or back lash to avoid metal to metal contact of rotor & stator. This unique design provides smooth & consistence all round performance & ong life of rotor & stator. Leak proof neoprene sealing device. Three way cock system for draining & recirculation of liquids provided as standard. Extra discharge spout provided as standard for viscous products. DOL Starter with over load relay for protection against single phasing & low voltage. Contact parts can be easily dismantled for cleaning. Special design facilitates adjustments of the grinding gap by an exterior screw by means of handle even during operation. Flame proof motor &Flame proof rotary switch can be provided on request at extra cost.  Output Depending upon material characteristics viscosity, density & micron size.

By way of introduction. We are pleased to introduce Parag Pharma Pump And Equipment is one of the leading manufacture of Inline colloid Mills developed for the first time in India, suitable for total dispersion of pharmaceutical formulation, creams and cosmetics,ointment,food products,etc. The process is carried out in single pass under a closed and pressurized system with improved color, reactivity and with no contamination. They come as tailor made for particle size reduction. This allows the industries to choose the colloid mill as per their specific requirements. The construction of the Mill is in stainless with built in jacket for heating or cooling, serrated rotor stator design with calibrated hand wheel adjustment with micrometer indicator for precisely varying the grinding gap between rotor and stator during the operation. In a short period of time we have achieved high level of technical excellence meeting the customers requirement resulting in an acceptable quality supported by series of trials conducted at our works. SALIENT FEATURES Inline Horizontal design Works under closed and pressurized system Process is carried out in single pass under hydraulic shear Discharge at elevated level Temperature rise is minimum and no aeration Quality uniform throughout the batch Can handle high viscosity media Improves color, reactivity with no contamination Jacketed mill housing for heating/ cooling Simple to use, easy to clean, less expensive to maintain Parag Pharma Pump And Equipment has develop for the first time in India, Horizontal Model inline-Colloid Mill for the Quick processing of all types of emulsions, dispersions of various media and micro grinding under wet condition. Colloid Mills have innumerable users. To list a few, manufactures of adhesives, cosmetics, coatings, ceramics, dyes and pigments, food products, insecticides, latexes, paints, toothpastes, pharmaceuticals etc. Parag Pharma Pump And Equipment backed by the two decades of technical excellence and experience in the process industries has the answer for getting difficult solid-liquid and liquid-liquid product mix inti.  

• Unique for Grinding , Homogenizing , Emulsifying , Dispersing , Mixing and Extracting. • Versatile Machine for Homogenizing and Milling Upto 5 to 10 Micron Particle. • Three way Cock System for Draining and Recirculation of the Liquids Provided as Standard. Extra Discharge Sprout Provided as a Standard for Viscous Products. • Modified Design of Semi Concave Teeth in Rotor and Stator Reduces Motor H.P. and Gives Better Perfomance in Size Reduction without Damaging the Product. • Contact Parts Can Easily Dismantled for Cleaning.

Colloid Mill, Sigma Mixer Machine, Flaker machine, Octagonal Blender

colloid mills manufacturer, Nitrous Oxide Gas Plants, air tray dryer

Colloid Mills, Liquid Laboratory Stirrer