Construction Machine Dealers in Chembur, Mumbai

Description:GF foaming concrete brick machine is designed for compact construct, small volume, easy to move. Pumping, foaming and mixing system are assembled as a whole body,  very convenient to use. This CLC foam concrete machine adopts single phase motor as power. The power is moderate, and GF5 CLC concrete machine is very convenient for family constructionTechnical data:Model-GFMax. theoretical concrete put(m³/h)-5Motor power(kw)-4.5Theoretical vertical conveying height(m)-40Theoretical level transmission distance(m)-300Mixer tank capacity(L)-200Filling height(mm)-880Overall dimension(mm)-2100*1340*1390Total weight(kg)-910Applications:1. Lightweight concrete machine can be used for providing insulating layer on the floor.    It can adjust the density according the mix design from 250-1600kg/m3.2. CLC block machine can used for roof insulation of refrigerated storage space.    Besides, it can be used for filling tunnel and mined.3. CLC making machine can be used for producing foam concrete panel and CLC block.

Guniting Hopper refers to the dry-mix process, in which the dry cementitious mixture is blown through a hose to the nozzle, where water is injected immediately before application.. The concrete is blasted by pneumatic pressure from a gun, hence "gun"-ite. Guniting means blowing dry material out of a hose with compressed air, wetting it as it was released. This was later used to patch weak parts in old buildings. Guniting Hopper or "cement gun" is the equipment used, and "gunite", the material that was produced. The dry mix method involves placing the dry ingredients into a hopper and then conveying them pneumatically through a hose to the nozzle. The nozzleman controls the addition of water at the nozzle. The water and the dry mixture is not completely mixed, but is completed as the mixture hits the receiving surface. This requires a skilled nozzleman, especially in the case of thick or heavily reinforced sections. Advantages of the dry mix process are that the water content can be adjusted instantaneously by the nozzleman, allowing more effective placement in overhead and vertical applications without using accelerators. The dry mix process is useful in repair applications when it is necessary to stop frequently, as the dry material is easily discharged from the hose.

• Working Width: 60” (1500 mm) Also available upto 5.5 mts (5500 mm)
• Floor Space 60” (1500 mm): 13 ft x 8 ft.
• Working Speed: 50 Mts. Per/ min
• Max. Unwind dia: 40” (1000 mm)
• Max. Winding dia: 40” (1000 mm)
• Type of material: Paper/ Fabrics / HDPE
• Core ID at winding & Unwind: 3” (76 mm) / 4" (100 mm) Paper core
• Power required: 10 HP (440V 50Hz)
• Optional: Center Web Guide, Shaft Less Unwind uni

Our drum mixers are light and portable with electric or air motor and ideal for easy and rapid stirring up suspensions and mixing additives in drums. For convenience and safety the unit incorporates a threaded 2" BSP or NPT bung adaptor nipple to allow mounting on standard 55 gallon ( 205 liter) drum. Models are available with either folding propeller or fixed blades.

Consider our name for purchasing top-of-the-line quality Loaders at competitively low prices. For the convenience of customers, we issue an invoice to them including details of transaction. Moreover, we maintain transparency in our payment procedure and dealings. The JCB Backhoe Loader, supplied by us, is highly reckoned for its long service life.  

• Accuracy: +/-1%
• Dimension: 810 X 400 X 860mm
• Model: GT-N09
• Measuring Range: 0-200kg
• Compression Speed: 12.7mm/min
• Resolution: 1/10,000
• Weight: 60kg

• Type: Bar Cutter
• Model Number: V40
• Brand Name: CM

Cutter with vertical cutting action. Blade width is 95mm therefore ideal for cutting multiple bars eg 25x2nos  20x3nos 16x5nos  12x7nos  10x8nos  etc ... Max Bar cut is 40size 

We export and supply all types of Hand tools like pliers consisting long nose pliers, diagonal cutting nipper bent nose pliers, end cutting pliers, grove joint pliers, All types of Industrial Sockets like Deep socket, standard socket, bit socket, star socket etc All type of wrench like half moon ring wrench , star box end wrench, flare nut wrench, combination swivel head socket wrench double swivel end socket wrench, half moon ring wrench, star box end wrench, flare nut wrench, combination swivel head socket wrench, double swivel end socket wrench etc. We supply branded quality tools which is high in quality and tested for performance. Packing : International Standard Export worthy packing with materials coding and customize marking on every pack for quick and easy identification for stores and user for easy updation in the software.

Being the pride of the whole B-LIFT line, the High Range, with its machines from 39m up to 62m, is a new platform line able to meet the requirements of different segments of various markets. Through the integrated projects and brilliant performances these machines are able to compete at a global level with the main competitors. Big variety of accessories for the most demanding uses

Salient Features: Low noise level, high performance Low running cost, High productivity Cost effective compared to CNC machines Minimum bend radius = 1.5D Sturdy Frame: Minimum deflection & uniform distribution of load Main Cylinder Ram : Operates at minimum working pressure for trouble free operation Electrical / Hrdraulic components procured from reputed companies lik Yuken, Hydrome/ Cross (Hydraulic) Mitsubishi & Telemecanique (Electrical)

Automatic Batch Printing Machine is commonly used in pharma, Food , Cosmetics edible oil ,lube oil &  bakery products, and allied industries  suitable to neat, sharp & registered print Batch Number, Date Of Manufacturing, Expiry Date, Prices, best before dates, applied on  labels, cartons and pouches. with the help of Rubber or Polymer flat Stereos. Machine with automatic feeding System, Stack of Pouches/ cartons is pulled or pushed by roller & collected from the tray after printing the message.     Specifications Over All Dimensions : 850mm X 765mm X 575mm Speed : 125/180/250 imprints per minute. Printing Media : Fast dry permanent paste ink or Liquid Ink Label, Pouch or Carton Size : Minimum 75mm X 35mm to Maximum 300mm X 200mm Motor : ¼HP/ 0.18KV 1440RPM (50Hz) Power : 230 Volts, Single Phase or 400/440 Volts, 3Phase Weight : Approx 95 kg Applications : Label & Sticker, PVC Shrink Sleeve, small carton, pouch and sachet.

• Certification: CE Certified
• Weight: 10-20kg
• Driven Type: Electric
• Warranty: 1year
• Pack Type: Box

Salient Features: Sturdy & robust construction Heavy duty bearings for long trouble free service. Totally enclosed construction keeps dust, dirt away from windings Low noise as compared to Electromagnetic Vibrators. Centrifugal Force can adjusted infinitely from 0 to max. Amplitude of vibration can be controlled. Low maintenance due to absence of belts, pulleys, Chains, Sprockets etc.

Our company is engaged in the manufacture and supply of the premium quality Transit mixer spare parts. We offer a wide range to our esteemed customers. These mixer accessories exhibit excellent durability and reliability. These products are highly demanded in the international market for sturdy construction and efficiency. These products are widely accepted in different industries due to their features of optimum reliability, good strength and long service life. We offer these at the market leading prices  Transit mixer spares water pump gear box water pump accessories transit mixer drive drum roller assembly roller bearing skf air filter hydraulic filter Tried and tested technology in UAE harsh working conditions 6 cubic metre & 9 cubic metre mixer available for mounting on Indian truck. Mixers with power take off arrangements are also available. Drum and internal spiral are made with special grade wear resistant steel. Main frame is designed with rectangular hollow sections to give extra The modeling and design of this equipment has been done in UAE and the Same is tried and tested with rigorous working conditions in UAE for long working hours and fast movement with rapid trips at long distance. The same technology is now incorporated in Indian build truck mixers. The drum has been designed with higher thickness of special wear resistant steel to give maximum drum life. With proper maintenance the drum life can be enhanced further.The drum roller supports are of very high capacity to take shocks of Indian bumpy roads. The roller are properly sealed with double thrust bearings. Hydraulics and gear box which are vital parts of the machine are used from recognized imported brands with proven track records.

block ice plants offered by us are developed by a team of experienced professionals, in tandem with the norms and guidelines already laid down by the industry. offered range of plant consist a brine tank, an electrically operated crane, a thawing tank, a tilting device with an inclined wooden table to receive the ice blocks as they slide out of the cans and filler. operations/ functions the ice machine & harvesting section of the plant consists of the brine tank, an electrically operated lifting device (crane) running on rails along the sides of the tank, a thawing tank, a tilting device with an inclined wooden table to receive the ice blocks as they slide out of the cans and a filler. Standard rectangular 25,50 & 150 kg ice cans, the brine tank is covered with solid wooden lids as shown on the picture. the machine room occupies the rear the machine room accommodates the brine chiller with the liquid separator the brine recirculation pump the air or water cooled condenser the refrigerant receiver the electric switch board and other accessories which are connected to one another through refrigerant and brine piping as shown on the piping diagram and the electrical wiring cold pips and vessels are insulated as required. the refrigerant evaporating in the brine chiller cools the brine the cold carrier which is recirculated by the brine pump from the brine tank through the brine chiller and back to the brine tank. The recirculated quantity is sufficient to facilitate adequate agitation in the brine tank. Removal of the process heat takes place in the air or water cooled condenser. Liquid refrigerant collects in the liquid receiver from where it passes over an expansion device back to the brine chiller. the refrigeration capacity required to maintain the temperature in the ice storage is small compared to that of the block ice plant, therefore, to simplify design and minimize service and maintenance work, the ice storage is cooled with the ice storage is cooled with an air-cooler refrigerator through brine pumped from the brine tank, for which a small brine pump is provided. the two main sections of the plant, namely the ice making & harvesting and the machine room & ice storage are placed side by side on the installation site and interconnected by the supply and return lines for the brine and electric power supply for harvesting and lighting. application cooling. food preservation. distance transportation. fresh keeping for aquatic products. ice factory of the ports and docks. special areas of cooling advantages capacity modulation and precision cooling high energy efficiency compact ozone-friendly refrigerants proven technology wide voltage range superior quality wear resistant part steel fabricated acc(air cooled condenser), low vibration, and low noise level.  

• Brand Name: Boss
• Power: Electric
• Usage/Application: Industrial
• Automation Grade: Automatic

• Weight: 100-1000kg
• Power: 1-3kw
• Driven Type: Electric
• Automation Grade: Semi Automatic
• Application: For highly sensitive instruments like Electronic Balance.
• Usage: Laboratory

The anti-vibration table is designed for use in the laboratory or metrology room to provide suitable working conditions for devices that are sensitive to vibrations and shocks. The table comprises two separate parts – An internal working surface consisting of a large granite slab mounted on rubber shock absorbing mounts. An external service table with steel frame and adjustable leveling feet.

Features: Utility van cum aerial work platform. Enough space for storage of tools and Tackles.  Aesthetically more pleasing. Optional Insulated basket for electrical work. Best suitable for working any season including monsoon.

Features of Mobile Jaw Crusher- Hydraulic-drive feeding plate is convenient and reliable. Easy to control by equipping with high-tech LCD touch screen and PLC control system. Feeder grates pre-screen scrap and excurrent material can be conveyed by side belt or main belt either. Belt conveyors and Magnetic iron separator are easy to use.

Pipe Bending Machine is widely used to create single or multiple bends in the pipe creating the desired shape or form. We, as a reputed Manufacturer and Supplier, bring forth the best quality Pipe Bending Machine. Our Pipe Bending Machine delivers excellent performance. Moreover, we can easily handle the bulk orders of Pipe Bending Machine as per the requirements of the clients. Attributes : High performanceRugged constructionBest quality Affordable

• Voltage: 380-440 V
• Weight: 165 kg
• Country of Origin: Made in India
• Power Consumption: 5.5 Hp
• Automation Grade: Semi-automatic
• Grinding disc width: 230mm*3

Batching plants are machines which mix the different ingredients of concrete homogenously to produce a perfect mix of concrete. Schwing Stetter India manufactures a wide range of batching plants that can be broadly classified with respect to their design, batch size, material storage (Aggregate Storage), and mixer technology. Schwing Stetter India analyses each customer’s requirement and guides the customer to opt for that batching plant which would suffice his needs of concreting, from the wide range available.

We have developed fast cutting & long life blades for green concrete. The main thrust is on quick initial cutting. Which reduces risk of cracks due to late cutting in PQC. Concrete Cutting Blades Different blades for various applications.green concrete, cured concrete,asphalt or dbm cutting The sizes available are 3.2 mm to 3.6 mm Thick dia 300 350 400 mm. to 18mm thick in 2000mm dia. Cured concrete cutting: The sizes available are 3.5mm to 12 mm thick. Dia 300 to 2000 mm. Used for widening of grove concrete full depth cutting of pavements.. Asphalt cutting Blades: popularly used for cutting asphalt roads, trimming sides joints.

batch bleaching plant, Acid Oil Plant, Hydrogenation Plant

• Power: 80 HP
• Salient Features: Plants are provided with Large Bins, Twin Shaft Compulsory Mixer, Inclined Aggregate Conveyors & Accurate Software for quick batching, quality mixing and safety
• Brand/Make: Penta
• Model Name/Number: Compact 30
• Mixer Type: Turbo Pan Mixer
• Output Capacity: 30 m3/hr
• Air Compressor: 5 HP
• Water Tank: 200 L (3 Loadcells)
• Input/Output Capacity: 750/500 Ltrs.
• Output Batch: 0.5 m3
• Mixer Motor Power: 1x22 kW
• Greasing System for Mixer: Automatic
• Standard Number of Bins: 4 Compartment Bins
• Bin Capacity: 6 m3
• Weighing System: PLC Based System through PC
• Aggregate Weighment: 1200 Kg
• Cement Hopper on 3 Loadcells: 300 Kg
• Additive Tank on 1 Loadcells: 10 L
• Air Capacity: 14.7 cfm
• Standard Screw Conveyor: Dia. 168x13 m
• Standard Supply of Screw Conveyor: 1 Piece
• Control Cabin: 7.5 x 7.5 Ft.

Top & Sink Bowl - SS 16 SWG SS 304 Sunk In Top 16 SWG SS 38 mm Round Pipe with Adjustable Nylon Bush 32 mm SS 16 SWG Round pipe for Cross support All Joints duly Argon welded, Ground & Buffed for Uniform Matt Finish 1 ½“ Sink Coupling with flexible PVC drain pipe Sink size can be Custom Made as per requirement 16 SWG SS 304 Top & Sink Bowl 1.5” Round Square Pipe Uprights 1” Round Square Pipe Cross Bracing 1.25” or 1.5” Sink Drain Outlet

Superior sweeping performance in the harshest, most congested sweeping environments Maximize sweeping safety with TotalView™ glass doors and cab forward design Consistent performance – any season – with state-of-the-art, dry dust control system Automatically adjust to surface variations with the industry`s only center suspended, floating main broom Maximum operator comfort with roomy, sealed cab interior that keeps out noise and dust down to 3 microns 4 wheel steering for brilliant maneuverability Path width 3200 mm 126 in; Hopper capacity 2600L; Power source turbo diesel Optional Multi-level dumping with hopper overload indicator – enables you to empty debris wherever you need Designed for use in industries, airport, cement plants, street, parking lots, airports, etc

RANGE – 5 Ton to 100 Ton We are engaged in manufacturing and supplying a wide array of C-Frame Press. The offered machines are fabricated using premium quality raw material and advanced technology that ensure their durability.  Product features: Specially designed for multiple – hole punching and Notching with unit tools. Use as press Brake for Bending. It is designed for various applications such as straighting, Trimming, Punching, Stamping, Notching and Bending. Its unique designs offers flexibility and ease of operation as three sides of the machines are open. Special guiding arrangement. Suitable for high productivity.

We have established ourselves as the prominent manufacturer, exporter and supplier of the Hydraulic Pipe Bending Machine that is designed by our team of experts using the advanced technology. Known for DurabilityCorrosion resistantOptimum Performance Applications Material handling equipmentsRefrigeration pipesChemical Plant-Petrochemical PlantsIn Automotive and other vehiclesBoiler tubesConstruction industryAgriculture sectorElectrical appliances

Table Top Model, Closed Cup Type, Economically priced, For small print areas, 100 % FESTO Pneumatics, Proximity switch based controls, Easy to shift, Suitable for Ceramic Steel Cup Rings, For small print areas within 60mm Diameter, Microprocessor based, Works on Single Phase Supply.