Cooling Tower Parts Dealers in Andheri East, Mumbai

• Size: 28 X 28, 35 X35, 65 X 65, or According To Clients Requirement
• Material: PVC
• Warranty: 1 Years

Cooling Tower Fill Is The Main Heat Transfer Area Available For Heat Transfer From Hot Water To Cold Air. The Splash Fills Disintegrates The Hot Water From The Vertical Direction And It Splits The Water To Pass Through Next Level Of Splash Bars.. Fills Are Normally Made Of Pvc, Wood.

• Coating: Gpld
• Model Name: VJ2.4
• Raw Material: Brass
• Code Through Hole Type: VJ2.4/ 001
• Code Shut Off Valve Type: VJ2.4/ 001 - V
• Series: 60

drive shafts in hot dip galvanized steel and stainless steel grades. The couplings are normally of cast iron. Cast stainless steel Grades are available upon request. The drive shafts are suitable for fans ranging from 8’ to 33’diameters . The drive shafts are tublar floating types and have flexible flanged couplings at both gear and motor ends , to compensate for any misalignment . The flexible elements are neoprene bonded metals. The length of the drive shafts are as per the cooling tower requirements. The drive shafts are dynamically balanced confirming to ISO 1946 Grade 6 prior to dispatch.

We are offering PVC Drift Eliminators manufactured from rigid PVC and are designed to remove entrained particles from air steam efficiently, with minimum pressure drop, thereby reducing the fan power requirement when the air passes through the drift Eliminator. Water droplets are separated from the air drift at the three direction change points on the drift eliminator. For crossflow tower applications, the almost vertical water conduits provided by the SPC 100 drift eliminator remove the water droplets out of the drift eliminator area and return them back into the tower and does not allow any re-entry. The special locking pin arrangement for SPC-100 facilitates quick and simple assembly at site. When used in counter-flow cooling towers, the measurable residual liquid load behind a droplet separator characterizes its efficiency. The performance data of our droplet separators have been determined under laboratory conditions. At a face velocity (CA) of 3.5 ms and a specific water flow (rw) -22tm2 h, the residual liquid load of the air is 15mgm3. If this residual load is related to the circulating cooling water volume this equates to a value smaller than 0.001%.   Fundamental conditions required to achieve these high efficiencies in practice are, a workman like installation, the droplet separator sections must be installed without any gaps between themselves or the tower walls to ensure by passing does not take place. The face value shall not exceed the maximum permissible value at any position across the total area of the separator. Any performance testing of the separators must be carried out immediately above the separators and by using a test method consistent with that employed in our laboratory or otherwise agreed with ourselves. We can advise on the likely operating efficiencies of specific towers provided that their operating data are made available to us.       Application Areas : Primary setting in wastewater treatment plants (suspended and flocculated solids) Secondary (biological solids) setting in wastewater treatment plants Solid-liquid separation in potable and industrial process water treatment plants, Anaerobic digesters (restrict loss of solids) Ash handling units in thermal power plants Process industry (material recovery from wash storm water) Oil-water separation

Over the past three decades, COOLDECK has established itself as one of the leading manufacturer of cooling tower Components. Fills, drift eliminators, fans and nozzles for both crossflow cooling towers as well as counterflow cooling towers. Our products have been installed in across the cooling tower consumer spectrum including power, industrial and HVAC segments. We bring to you a combination of our functional knowledge of cooling towers along with deep expertise in polymer engineering and top that off with superior pre and post sales service in the cooling tower field. You can count upon COOLDECK to not just deliver products but assist you with cooling tower performance and upkeep issues.

• Material: Rigid PVC
• Maximum Face Velocity: 4.5 m/sec
• Module Length: Can be chosen in 600-mm increments.  Max suggested length – 1800-mm
• Module Depth: 130 / 146 mm
• Pitch: 20 mm
• Pitch: 20 mm
• Maximum Spacing of Support with  standard thickness of sheets: 800 mm
• Directional changes for air flow: 3
• Standard Thickness (Corrugated/Plain): 0.3mm/0.4mm
• Average Weight: 7.6 / 8.5 kgs/m2
• Expected Drift Loss: < 0.001% / 0.0005% of circulating water
• Maximum Continuous Temperature (deg Celsius): 55°C

  Various spares available such as Fan Assembly, Sprinkler, Header, Fillings,      Motor, Structures, FRP Components, etc.   For any make, any type and any capacity

Cooltech Cooling Equipments uses high quality cooling tower spares like Rotary Sprinklers, PVC Fills, Fan Assembly and FRP Casings for Cooling towers. Cooltech is also a supplier of Cooling tower spares contact 9322274824 to order any of these spares which are available in different sizes for different capacity cooling towers.

aluminum fin, F.T.L Caps & Lamp Caps, aluminum gasket, aluminum vial seals