Electronic Circuit Boards Dealers in Deonar, Mumbai

• Shelf Life: 24 Months from Date of Manufacture in Sealed Condition.
• Packaging: 400 Ml Aerosol Spray - 550 Ml Aerosol Spray

High Gloss Fast Drying Flexible Acrylic Conformal CoatingELECTOCOAT is a fast air-drying, lightweight, clear, tough and flexible acrylic coating designed primarily to protect printed circuit boards and electrical / electronic equipment against high voltage arcing, corona shorts, corrosion, ingress of moisture and fungus. It resists rust, tarnish, corrosion, moisture and has excellent waterproofing / weatherproofing abilities. ELECTOCOAT is highly abrasion & scratch resistant and protects electronic equipment completely due to its high dielectric strength. It does not contain any harmful chlorinated solvents, CFCs or ozone depleting chemicals.Benefits Protects against rust, corrosion, tarnish, oxidation, moisture and weathering influences Provides a high-gloss, clear protective finish that remains transparent and does not fade or become yellow Provides a protective and insulating film that shields printed circuit boards from electrical leakage and short circuits Prevents sparking and corona discharges Non-conductive and has good dielectric properties Excellent resistance to weak acids & alkalis, water, oils and chemical fumes Easily solderable and very convenient for onsite repair jobs Conforms to requirements of specifications MIL-I-46058C Applications Insulation and protection of all electrical, electronic and high- tech equipment of: general electronics, printed circuit boards, thick film circuits, high voltage transformers, electrical motor coils, cables, wires; for moisture proofing and corrosion prevention of any industrial, automotive, aviation, marine and military electrical & electronic hardware.Directions For Use - Bulk Mask and protect areas not to be coated. Apply steady even strokes by means of brush. Component to be coated can also be dipped into the coating. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity.Directions For Use - Aerosol Shake can vigorously for at least one minute after bearing noise from inside the can is audible. Mask and protect areas not to be coated. Hold can 12-15 inches away from surface to be coated and spray in steady, even strokes. For best results, two light coats are better than one heavy coat. Coating becomes dry to touch in about 15-20 minutes. Complete cure takes place in about 24 hours depending upon the relative humidity. Clean the valve by inverting the can and spraying a few short bursts till only the clear propellant comes out. Clean the actuator button orifice by means of a thin, fine wire.Caution:- Contains flammable propellant and solvents. Do not spray near naked flame, hot surfaces or energized equipment. Use with adequate ventilation.

The company has made a formidable base in the domestic and international markets as a Manufacturer, Exporter and Supplier of Ultrasonic PCB Cleaning Machines in Mumbai (India). The Ultrasonic PCB Cleaning Machine is normally used for cleaning the assembled PCB as when the components are assembled on PCB, a lot of flux is formed during the soldering. The ultrasonic cavitations provided by the Ultrasonic PCB Cleaning Machines helps in removing this flux, dust and other contaminants from the soldered surfaces of PCB and improve the overall function of circuitry. The Ultrasonic PCB Cleaning Machine is also used during the manufacturing process of PCB to clean the small holes. Why Our Ultrasonic PCB Cleaning Machines? Highly durableEfficient and reliableCompact design and easily portableSimple operation

Spades and spacers are designed to isolate sections of pipe to prevent contamination and allow inspection. Our spades and spacers are made from duplex, super duplex, 6% moly, nickel alloy and stainless steel to ensure they are strong and corrosion resistant. Our spades and spacers are available dimensionally in accordance with API 590 and ASTM 16.48 or customer requirements.  

• Features: Excellent finish , Lightweight, Long working life.

• Colour: Red,Yellow,Green,Blue

We offer Electronic Jewellery Rate Board. Prices in this board can be changed vi Remote ControlPC. Number of Lines can be increased or Decreased as per clients requirements. * Completely Customised.

• Brand Name: EPS / SAI

We are offering printed circuit boards. All types of electronic printed circuit boards. Single and double sided including aluminium base for leds. Laminate materials: phenolic, composite cm 1, glass epoxy,fr1 base. Laminate thickness: 0.4 mm to 3 mm, sizes: width size of b 450mm x l 750mm max. copper cladding: thickness of 0.25 mm to 0.75 mm

tv kit, Public Address Systems, Electronic Items, tuner, Diaphragms

electronic circuit boards, automatic test equipment, mill grade ups, Modules

Esd Protection Devices, Plug Gauges, Electric Receptacles, T Connectors

Printed Circuit Board, Pitch Connector, white pcb connector, Terminal Block

Printed Circuit Boards, double side boards

Inverters, Printers

Inverters, Uninterrupted Power Supply

Inverters, Transformers, ups systems, Voltage Stabilizers

Inverters, Automotive Tyres, tubes, Batteries

Inverters, Laptop, Notebooks

Inverters, Ups, SMF Batteries, Industrial Battery, silver oxide battery

Inverters, ups systems, Fire alarms and Security Systems

Circuit Boards, Printed Circuit Boards

Camera Module, Robotics Gear Motor Kit

Circuit Board, Electronic Component, semiconductor devices, Smd Capacitors

Inverters, Home Appliances, power batteries

Inverters, Inverter, lit power conditioning unit, solar green pump