Elektromag-Joest Vibration Pvt. Ltd. Prabhadevi, Mumbai, Maharashtra

Limit Switch is a switch operated by the motion of a machine part or presence of an object. These are used for control of a machine as, a safety interlock or to count an object passing a point. Limit Switch may be directly mechanically operated by the motion of the operating lever.

Current Rating : 40 AMPS at 500 V.A.C.

ELEKTROMAG are the pioneers of the Indian Crane Control Gear Industry. These EM Brakes are used when a load must be stopped rapidly to prevent the load from rotating due to the motor and load inertia. EM Brakes have found innumerable applications where stopping of a machine is necessary by automatic control whether it is a question of stopping at a pre-determined timed or at selected points of travel or to prevent over travelling. All types of brakes are normally applied when in OFF position and the brake is released when power is ONconnected. Brakes upto 400mm diameter for Braking Torque as per client’s requirements can be supplied.

Electro Hydraulic Thrustor Brake is a heavy duty brake designed to withstand the severe duty conditions imposed by heavy duty machinery in various industries. Electro Hydraulic Thrustor transmits useful thrust through the lever onto the brake shoe thereby releasing the brake. When the power is switched OFF, the brake is smoothly applied because the hydraulic thrust acting against the spring pressure is gradually reduced. Electro Hydraulic Thrustor: It consists of a cylinder filled with oil and having a centrifugal pump at the bottom of the cylinder. The centrifugal pump is driven by a 3phase fractional horse power Class ‘B’ insulated, continuously rated rotor and stator. Specially designed radial impeller permits operation of the pump in either direction of rotation. Thrustor conforming to IP-55 & adjustable time lag on both up & down stroke can be supplied at extra price.

Solar thermal collectors use the power of the sun to provide heat for space heating and hot water -- for free, reliably, and without an environmental impact. The heart of flat-plate and evacuated-tube collectors is the absorber. It takes up the energy in sunlight and converts it into heat. The more efficient the absorber, the greater the collector's output. With its highly selective blue TiNOX energy absorbers, Almeco sets industry standards. These products absorb 95% of incident sunlight. At the same time, they only lose some 4% of heat radiation, so that around 90% of the solar energy can be used as heat. In this way, manufacturers of flat-plate and evacuated-tube collectors can ensure the greatest quality and maximum yield for their customers. Almeco applies its highly selective absorber layers both to aluminum and copper substrates in a high-tech coating process. Collector manufacturers are then able to offer a wide range of high-quality products with TiNOX energy. No other company in the world has as much experience in the production of highly selective absorbers; after all, TiNOX invented this technology in the mid-1990s and has continued to further develop it since. All TiNOX energy products are made in Germany on modern production lines in Munich and Bernburg (Saxony-Anhalt). Almeco offers a 10-year guarantee for its TiNOX energy products. A number of renowned testing institutes have confirmed the high quality of TiNOX energy absorber's with their findings.

Magnetic Drum Separators are essential in every processing industry and are widely used for the separation of iron contamination from minerals, chemicals, food, flour, sugar, grains, plastics, sand, cement, fertilizers, rock, borings and many other gravity or conveyor transported products. The Drum Type Separators can be either permanent magnetic or electro magnetic, depending on the nature of the application. Permanent Magnetic Drums may use either Ceramic magnets for low intensity applications or Rare Earth Magnets for medium intensity applications. Permanent Magnetic Drums are usually made in the diameter range of 300mm to 900mm and widths up to 3000mm. Electro Magnetic Drums are supplied for a larger and more heavy duty applications typically in slag recycling or auto recycling industries.

Powered by clock type springs and rotating on sealed for life bearings. ELEKTROMAG drum offer a convenient, cost effective means of supplying power to moving machinery. With heavy duty, one piece drum halves and a painted finish the reels are suitable for operation in arduous conditions. ELEKTROMAG springs have been proved in service for many year and are manufactured from the highest quality materials. They are of the “clock spring” or spiral wound type and by using the springs singly or assembled in series or in parallel, a wide range of performance characteristics is obtained from the standard range.

"ELEKTROMAG" MAGNETIC FLOOR SWEEPER is the most effective and economical answer to damaging nails, screws, rods and dangerous scrap metal of all kinds lying scattered on roadways and factory premises. The Magnetic Sweeper can pick up everything from fine iron to heavy bolts, nuts, washers, screws, turning, borings, rivets, nails, pins, staples etc., lying on the floor. The Magnetic Sweeper finds wide application in machine shops, repairshops, garages, metal working assembly plants, scrap yards, ships, warehouses, building constructions, airports and parking lots. A considerable amount of time is saved in magnetically sweeping up and reclaiming ferrous trash by this process instead of manually brushing the floor. The considerable savings resulting from the use of this Sweeper makes it pay for itself within a short time. Furthermore, the Magnetic Sweeper helps prevent accidents by removing sharp edged objects that could penetrate shoes or injure bare feet. Also, steel chips, turning embedded in shoes cause damage to office furnishings such as carpeting, flooring etc.

ELEKTROMAG Moulded Plastic Cable Drag Chains are a logical addition to the range of the steel Cable Drag Chains which have proved themselves worldwide for over 25 years. The chain links and separating plates for taking the cableshoses, from a single unit in the ELEKTROMAG Cable Drag Chains. The individual chain links can be connected by a snap connection enabling them to be joined to form a chain of any required length. One of the advantages of this system is that the customer can make up any required length of chain so that stocks can be kept and it is not necessary to place an order for each requirement.

Magnetic Separators and Suspension Magnets have become indispensable for decades. They are used for removing magnetic parts from non-magnetic materials in order to protect crusher, mills, processing plants etc. against too much wear and damage. They serve for cleaning non-magnetic bulk goods with iron contamination, for instance cleaning of foundry sand, coal and the like. They are used for recovering magnetic material from ore, steel mill slag etc. Generally, Overband Magnetic Separators and Suspension Magnets are installed above conveyor belts, vibratory feeders or chutes. They pick up ferrous metal parts from the bulk goods. In most cases, the magnet can also be installed in an existing installation without much expense.

'ELEKTROMAG' Electro Magnetic Clutches are used where frequent load cycling takes place. Where a motor must be accelerated and decelerated, there is motor heating which reduces the motor life. By installing a Clutch the motor can be operated at its normal speed and the load can be cycled by engaging and disengaging the clutch. 'ELEKTROMAG' Clutches have been designed for installations where a smooth take-up of drive is essential. Such applications include wire drawing, textile machines, rolling mills, welding plants, machine tools, shearing machine, etc.

ELEKTROMAG Rectangular Lifting Magnets, series LMQ B are mainly used for transport of sheets, billets and slabs. Around the central pole in the casing lies a coil-firmly connected to the casing by thermal conduction material. High- performance chains provide maximum safety when carrying the magnet. The cable connection point is also efficiently protected. Standard design WITHOUT POLE PLATE is used for transporting one-piece loads such as sheets or slabs. The pole plate design is used when the magnetic power must be distributed evenly over the full length of the magnet, as is the case, for instance, when transporting a layer of billets. All listed types are available with and without pole plate.

Limit Switch is a switch operated by the motion of a machine part or presence of an object. These are used for control of a machine as, a safety interlock or to count an object passing a point. Limit Switch may be directly mechanically operated by the motion of the operating lever.

Current Rating : 40 AMPS at 500 V.A.C.

Elektromag Magnetic Pulleys are generally used as the head pulley of a conveyor for separating iron pieces from conveyed material. Elektromag Magnetic Pulleys are used for all kinds of bulk materials, such as brown and pit coal, coke, like-stone, cement, rock salt, potash, chamotte, blast furnace, and steel mill slag, foundry sand, gravel, sand, synthetic granulates, grain and feedstuff. They can also be fitted as drive or return pulleys to the discharge end of rubber conveyor belts of existing installations at a later stage. ELEKTROMAG Magnetic Pulleys are mainly designed to remove large iron pieces, such as bolts, screws, wire, strips and tools which could damage conveyor belts, brake sieves, crushers or processing machines. Other Type of separating magnets are available for separating fine iron. In the event of slag separation they server – depending on the granulation – for parting magnetic and non-magnetic components. METHOD OF OPERATION The magnetic field produced is effective on the entire surface in the range of the conveyor belt. The magnetizable iron pieces contained in the conveyor material are influenced by the magnetic field and drawn on the conveyor belt. The iron pieces follow the run of the conveyor belt until they loosen from the magnetic field and, parted from the conveyor material, are discharged in the belt’s run direction underneath the magnetic pulley.

Magnetic Drum Separators are essential in every processing industry and are widely used for the separation of iron contamination from minerals, chemicals, food, flour, sugar, grains, plastics, sand, cement, fertilizers, rock, borings and many other gravity or conveyor transported products. The Drum Type Separators can be either permanent magnetic or electro magnetic, depending on the nature of the application. Permanent Magnetic Drums may use either Ceramic magnets for low intensity applications or Rare Earth Magnets for medium intensity applications. Permanent Magnetic Drums are usually made in the diameter range of 300mm to 900mm and widths up to 3000mm. Electro Magnetic Drums are supplied for a larger and more heavy duty applications typically in slag recycling or auto recycling industries.

These are designed for heavy duty Mill & Crane duty frequent operations suitable for voltage upto 600 Volts DC. Contactors are designed for mechanical duty Class 10 as per IS: 2959:1975. Rating ranging from 50Amps upto 600Amps are available in four types: 1) Single Pole D.C Contactor 2) Double Pole D.C. Contactor. 3) Triple Pole D.C Contactor 4) Four Pole D.C. Contactor. Details require for enquiry from clients are Current Range, Nos. of Poles, ACDC, No. of Auxiliary Contacts, Operating Coils Voltage & type of Main Contacts –normally open or closed.

The Widest Range under one Roof. Elektromag are the pioneers of the Indian crane control gear industry. With experience in this field for more than 5 decades we offer you the most comprehensive range of AC DC Brake, Clutch, Resistance Box, Master Controller , DC contactor, limit Switch etc, used by various crane machinery manufactures. Elektromag’s stringent quality checks and materials reduce your expensive production stoppages due to trouble free performance. This is the only reason why we are the people behind the scene of Major EOT Bulk MHE Industry

Limit Switch is a switch operated by the motion of a machine part or presence of an object. These are used for control of a machine as, a safety interlock or to count an object passing a point. Limit Switch may be directly mechanically operated by the motion of the operating lever.

Thousands of Elektromag's Circular Lifting Magnets have been in use for many years throughout the world. We can provide you with special designs and complete solutions. We provide more details of our products and their capabilities in the data overleaf. Take advantage of our expertise.

Elektromag offers a comprehensive range of products for the efficient, safe handling and control of cables and hoses including spring, motor operated reels and drag chains. Our factory houses full production capability alongside design and development facilities. Our Experienced technical staff can advise on the optimum solution to individual application and tailor our products accordingly, to ensure our clients receive the best solution with Quality assured.

2 PL Lamps 18 W (CFL) Double Parabolic Louvre (9 Cells - Square) made from Reflector Diffuse (Matt) finish imported Pre-anodised Aluminium having 86% reflectivity manufactured by Almeco, Italy. These Louvres are also available as tailor made due to CNC Flexible programming Machines and can be manufactured to suit your existing housings and also in Specular Mirror finish imported Pre-anodised Aluminium having 86% reflectivity manufactured by Almeco, Italy mainly used for CFLs.

The Anodising Process is an electrolytic process which results in the surface of the Aluminium Strip being converted to a layer of Aluminium Oxide which firmly adheres to the metal surface and forms a nearly homogeneous bond with the Aluminium. This oxide layer functions as an electrical insulator with insulating properties dependent on the oxide layer thickness. The oxide layer thickness is controlled during the Anodising process so as to meet the desired insulation level which would be adequate for the inter-turn voltage. For example, if the Inter-turn Voltage is 1V, then the insulating level would be in excess of 100V. The Al2O3 aluminium oxide layer has high wear and abrasion resistance. It has a melting point of approximately 2000oC which exceeds the melting point of 658oC of the base Aluminium metal. Thus, effectively the oxide layer would have refractory properties and a Coil made from Anodised Aluminium Conductor could insulate till it melts.

Voltage : 100V