Frp Fan Dealers in Mumbai

SCS aerodynamically designed Aerofoil axial flow fans manufactured from high quality epoxy grade FRP material save up to 30% power as compared to aluminum fans. SCS fans achieve the best performance keeping power consumption and noise levels to the minimum possible. Aerodynamic axial flow FRP fans manufactured by COOLDECK are specially designed for high-efficiency, critical applications, which include Cooling Towers, Humidification and Exhaust systems.     Key features   Tough light weight hollow FRP blades   Non-corrosive and erosion resistance   Different standard pitch angles/adjustable pitch angles   Wide range of industrial air moving applications   High efficiency and low noise levels   Aerodynamically designed for maximum airlift and minimum air resistance   Design Features   The unique aerofoil design ensures high efficiency, lower noise levels and less power consumption Reinforced Fiberglass Epoxy Resin (FRP) provides the desired non-corrosive quality to the fan blades, resulting the operation of fans even in the most aggressive environment.   The design of the fans provides high air volume with optimum pressure to ensure the long distance reach in the farthest areas.   The hollow construction of blades makes the fan lightweight resulting into low starting torque and reduced power consumption under varying load conditions. This causes minimum wear and stress on motor bearings and drive shafts.   By varying chord width and angle of incidence along the length of the blade SCS fans yield significantly higher performance than constant-chord-width fans as they develop constant velocities along the full blade length.   SCS FRP Fans with pitch control enable the field technicians to change pitch settings easily in order to optimize fan performance or to change field applications.

Frp fans, Impeller made of FRP using Vinyl Ester High HDT vinyl Ester (Epoxy Novolac based). Spilt Casing for ease of maintenance. Single piece bearing housingindividual plummer blocks, All Protection Guards made out of FRP.

PP / FRP centrifugal fan light metal performance parameters using polypropylene sheets, heating die welded together. Its widely used in scientific research, the chemical industry, metallurgy, electronics, pharmaceuticals, textiles, instruments, electroplating, mines, schools hotels, guesthouses, laboratories, environmental protection, and other ancillary equipment industry for ventilation exclude acidity, and other harmful gases ventilation in . Do not allow transmission of aromatic compounds, aliphatic and aromatic hydrocarbons halogen derivatives, ketones, and other corrosive gases. With corrosion-resistant chemical, it is not easy aging, the proportion of small, small mechanical vibration, low noise, smooth transfer characteristics. It does not allow transmission of gas containing viscous substances contained in dust and rigid particles ≤ 150 mg/m3, ≤ 50 ℃ gas temperature, relative humidity ≤ 100%. And avoid sun exposure, fans are prohibited in the vicinity of heat. 

• Power: 2.1 - 3.9 KW
• Type: Duct Mounted Fan
• Country of Origin: Made in India
• Material: FRP
• Fan Speed: 2800 RPM
• Features: High Durability, Easy To Clean

• Power: 3.9 kW
• Brand Name: R. K. Engg. Works
• Material: Cast Iron
• Voltage: 340V
• Air Volume: Approx. 9800 m3/h
• Phase: 3 Phase
• Frequency: 50 Hz
• Motor Power: 4 HP

SCS aerodynamically designed Aerofoil axial flow fans manufactured from high quality epoxy grade FRP material save up to 30% power as compared to aluminum fans. SCS fans achieve the best performance keeping power consumption and noise levels to the minimum possible. Aerodynamic axial flow FRP fans manufactured by COOLDECK are specially designed for high-efficiency, critical applications, which include Cooling Towers, Humidification and Exhaust systems.   Key features   Tough light weight hollow FRP blades   Non-corrosive and erosion resistance   Different standard pitch angles/adjustable pitch angles   Wide range of industrial air moving applications   High efficiency and low noise levels   Aerodynamically designed for maximum airlift and minimum air resistance Design Features   The unique aerofoil design ensures high efficiency, lower noise levels and less power consumption Reinforced Fiberglass Epoxy Resin (FRP) provides the desired non-corrosive quality to the fan blades, resulting the operation of fans even in the most aggressive environment.   The design of the fans provides high air volume with optimum pressure to ensure the long distance reach in the farthest areas.   The hollow construction of blades makes the fan lightweight resulting into low starting torque and reduced power consumption under varying load conditions. This causes minimum wear and stress on motor bearings and drive shafts.   By varying chord width and angle of incidence along the length of the blade SCS fans yield significantly higher performance than constant-chord-width fans as they develop constant velocities along the full blade length.   SCS FRP Fans with pitch control enable the field technicians to change pitch settings easily in order to optimize fan performance or to change field applications.

Frp Fan, FRP Pipes, FRP Blowers, frp impeller, frp pipe fitting

cooling tower frp fan, Cooling Tower Fan, cooling tower part

energy efficient axial flow frp fan, Air Cooler, Exhaust Fans, ventilation

FRP Exhaust Fan, Cooling Towers, Motor Cover, PVC Pipe Lining, FRP Pipes

FRP Base Roof Exhaust Fans, Axial Fans, Blowers, Dust Collectors

FRP Fans, Cooling Towers

Frp Fan, water distribution nozzles, Drift Eliminator, Fan Motor