Gas Pipe Fittings Dealers in Mazgaon, Mumbai

FAV range of Hydraulic Fittings provides secure, tough, and reliable tube connection that with exceptional leak-tight quality. FAV Hydraulic Fittings are available in Stainless Steel, Brass, Steel and Monel. Features 1)     International Standards 2)     Very effective seal between the fittings and the tubes 3)     Good vibration resistance 4)     High Pressure Rating Upto 10000 psi For use with applications such as: Construction machinery, Textile machinery, Machine tools, Chemical, Marine, Military, and most other high pressure hydraulic applications.Applications using thick wall tubing where flaring is not practical.7000 Flareless Fittingsare NOT RECOMMENDED for use in instrumentation applications where toxic and noxious gases are present.A bite type fitting is sometimes incorrectly referred to as a compression fitting. Compression fittings are designed for use with soft tubing and are not interchangable with bite type fittings   Tubing sizes are measured in sixteenths of an inch. Available sizes are 1/8" through 2". When ordering, the tube end of the fitting must be specified first followed by the pipe thread or straight thread end. All fittings in this section are ordered as assemblies only unless otherwise specified by customers when ordering   Hydraulic fittings  consist of a body, a one-piece ferrule, and a nut are available in carbon steel, brass, and stainless steel. With a large number of configurations, there will be a fitting that is ideally suited to meet the requirements of almost any industrial application. On assembly, the ferrule “bites” into the outer surface of the tube with sufficient strength to hold the tube against pressure and seal the fluid, without considerable distortion of the inside tube diameter. Hydraulic fittings have a visible bite, allowing the fitting assembler to visually inspect the bite quality, thus significantly minimizing the risk of improper assembly and related service problems. Hydraulic fittings are especially suitable for use with tube wall thickness ranging from medium to extra heavy. For proper bite, bottoming out the tube is essential for the make-up of the fitting. Leak-free performance is guaranteed when bite type fittings are assembled properly. No special tools are required to obtain proper installation.   Hydraulic fittings are also suitable for use with soft metal tube and various types of plastic tubes such as nylon, polyethylene, etc. When used with plastic tube, it is strongly recommended that a tube insert, be used to prevent tube pull out due to tensile loading. Our expertise lies in successfully designing and manufacturing of Hydraulic fittings We can deliver these in different designs as per the specific application demands. The range include Flareless Fittings, Flareless Bite Type Fittings, Union Fittings, Connectors, Elbow Fittings, Adapter Fittings, Tee Fittings, Nipple fittings, End Closure fittings, Cross Fittings and Nut & Ferrule fittings.  

We are offering stainless steel 316 double ferrule tee.pioneer is a manufacturer of fittings which are available in stainless steel and monel including male tee, female tee and union tee.

• Type: Tee
• Size: Carbon Steel Buttweld Pipe Fittings
• Technics: Forged
• Shape: Reducing
• Lead Time: Within 3 to 4 weeks after receipt of advance payment.
• Brand Name: Ravi Ratan Metal Industries
• Port: Nhava- Sheva Port, Mumbai
• Packaging Details: Standard Sea Worthy Packing or as per the customers requirement.
• Head Code: Hexagon

forged elbows: 90° elbow socket weld 90° elbows threaded 45° elbow threaded 45° elbows socketweld seamless elbows: 90° elbow long 45° elbows long 180° elbows long 90° elbow short 45° elbow short 180° elbow short welded elbows: 90° elbows long 45° elbow long 180° elbow long 90° elbows short 45° elbows short 180° elbow short elbows – material wise: titanium elbows tantalum elbow nickel elbows cupro nickel elbow zirconium elbows hastelloy elbow incoloy elbow niobium elbows hr alloy elbow alloy 20 elbow nimonics elbows monel,inconel elbow stainless steel elbows duplex, super duplex elbow production range: ravi ratan metal industries manufactures pipe fitting devices which are bent in such a way to produce some degree ( 90,45, 180 degree ) changes in the direction of flow of the content in the pipe. Elbows are manufactured tomeet different specifications, in terms of size and diameter. Ravi ratan metal industries manufactures & supplies high quality elbows that can be used for various applications. Our elbows are tested and verified for durability, accuracy and precision. ravi ratan metal industries manufactures forged, seamless & welded elbows (pipe fitting) of types 90° elbows, 90° elbow 45° elbows, 180° elbow of socket weld, threaded type to ansi b 16.5 from classes 2000 to 9000 and schedules from 10 to 160 . ravi ratan metal industries manufactures elbow (pipefitting) accordance with bs standard from classes 2000 to 9000 lbs, schedule 10 to 160 .

We are offering Double Ferrule Compression Tube Fittings to the clients. Available in the size range of 2 mm to 38 mm outer diameter tubing, these Double Ferrule Compression Tube Fittings are available with a variety of end connections and patterns as per customer requests. These Double Ferrule Compression Tube Fittings do not twist the tube during installation. Our range of Double Ferrule Compression Tube Fittings includes Double Ferrule Compression Tube Connectors, Double Ferrule Compression Tube Cross, Double Ferrule Compression Tube Elbow, Double Ferrule Compression Tube End Closure, Double Ferrule Compression Tube Tee, and Double Ferrule Compression Tube Union.   Attributes : Double Ferrule Compression Tube Fittings do not twist the tube during installation. Make and remake of the fittings is very much eased, as nuts are silver plated internally to prevent galling of threads. Low torque operation Positive leak free seal assembly and reassembly Size range from 116 to 2 (2mm to 38mm OD tubing) Variety of end connections and patterns as per customer requests

• Material: AISI304, AISI316L
• Size: 1/2""-12", DN10-DN300
• Feature: Corrosion Resistance, High Quality
• Machine Ferrule: By Forging, Then CNC
• Gasket Material: 1. EPDM, PTFE, Viton, Silicon
• Application: 1. Beer, Food, Dairy, Beverage, Cosmetics, Pharmacy and Chemical Etc Industries

• Application: Hydraulic, Industrial
• Feature: Fine Finishing, High Strength, Perfect Shape
• Technics: Forging, Press Fitting
• Form: Elbow, Nut, Tee
• Pressure: Medium Pressure
• Connections: Flange, Male, Welded

We are offering Buttweld Fittings. RANGE 15 NB UP TO 1200 NB IN SCH 5S , 10S ,10, 20 , 40S , 40 , STD , 60 , 80S , 80 , XS , 100 , 120 , 140 , 160 & XXS FORM :: SEAMLESS & WELDED LONG RADIUS & SHORT RADIUS ELBOW 90 DEG , LONG RADIUS ELBOW 45 DEG ,Long Radius & Short Radius Elbow 90 Deg , Long Radius Elbow 45 Deg , Long Radius & Short Radius Elbow 180 Deg ( Return Bend ) , Reducing Elbow , Equal Tee , Un Equal Tee, Crosses , Concentric Reducer , Eccentric Reducer , Long Stubend , Short Stubend , Coller , Pipe Cap , Long Radius Bends R =3 D , 5 D , 6 D , 8 D ,10 D & 20 D In 15 Deg ,30 Deg, 60 Deg & 90 Deg And Drawing Bassed Butt Weld Fitting ( Customised ). Stainless & Duplex Steel Stainless Steel ASTM / ASME SA 403 GR WP "S" / "W" / " WX" 304 , 304L , 304H, 304N , 304LN , 309, 310H , 316 , 316H , 317 , 317L , 321 , 321H , 347 , 347 H Duplex Steel ASTM / ASME SA 815 UNS NO.S 31803 , S 32205 , S 32550 , S 32750 , S 32760 . Carbon & Alloy Steel Carbon Steel ASTM / ASME A 234 WPB , WPC ASTM / ASME A 860 WPHY 42 , WPHY 46 , WPHY 52 , WPH 60 , WPHY 65 & WPHY 70 . Alloy Steel ASTM / ASME A 234 WP 1, WP 5, WP 9, WP 11, WP 12, WP 22, WP 23, WP 91 Nickel & Copper Alloy Nickel Alloy ASTM / ASME SB 336 UNS 2200 ( NICKEL 200 ) , UNS 2201 (NICKEL 201 ) , UNS 4400 (MONEL 400 ) , UNS 8020 ( ALLOY 20 / 20 CB 3 ) , UNS 8825 INCONEL (825) , UNS 6600 (INCONEL 600 ) , UNS 6601 ( INCONEL 601 ) , UNS 6625 (INCONEL 625) , UNS 10276 ( HASTELLOY C 276 ) Copper Alloy ASTM / ASME SB 111 UNS NO.C 10100 , C 10200 , C 10300 , C 10800 , C 12000, C 12200, C 70600 , C 71500 . ASTM / ASME SB 466 UNS NO.C 70600 ( CU -NI- 90/10) , C 71500 ( CU -NI- 70/30).

The major concern of our firm is to deliver a quality content, thus, we check the product quality on several counts at all stages. We are a quality driven firm ad thus make sure that the material used for manufacturing complies with high quality standards. As a result of which, the finished products have long service life. Features: High grade metal Dimensional stability Industrial application

• Material: Carbon Steel
• Thickness: 10-15mm, 15-20mm
• Application: Fittings
• Color: Black
• Feature: Corrosion Proof, High Strength
• Finishing: Polished
• Material Of Construction: 304,304L,316, 316L etc

Threaded Bevel Seat 90° Elbow 90° Reducing Elbow, Non Tapered so• Elbow, Plain Bevel Seat 90° Elbow Short Outlet Tea 45 Elbow Equal Tee Reducing Tee Instrument Tee Short Oudet Reducing Tee Equal Cross Long Weld Ferrule Short Weld Ferrule Ferrule for Expanding (Racesslass)

We are offering buttweld fittings. Range 15 nb up to 1200 nb in sch 5s , 10s ,10, 20 , 40s , 40 , st d , 60 , 80s , 80 , xs , 100 , 120 , 140 , 160 & xxs form :: seamless & welded long radius & short radius elbow 90 deg , long radius elbow 45 deg ,long radius & short radius elbow 90 deg , long radius elbow 45 deg , long radius & short radius elbow 180 deg ( return bend ) , reducing elbow , equal tee , un equal tee, crosses , concentric reducer , eccentric reducer , long stubend , short stubend , coller , pipe cap , long radius bends r =3 d , 5 d , 6 d , 8 d ,10 d & 20 d in 15 deg ,30 deg, 60 deg & 90 deg and drawing bassed buttweld fitting ( customised ) . Types: elbow, tee, reducer, return bends, stu-ends, cap, collar, cross, insertetc. Available in stainless steel & duplex steel, carbon & alloy steel and nickel & copper alloy, monel, nickel, inconel, hastelloy,titanium.

We are leading supplier of stainless steel ferrule fittings , our range of stainless steel ferrule fittings is highly durable. These are made using stainless steel and are offered in various forms as per the requirements of the clients. Our range can be availed in various grades at market leading rates. we have been offering a wide range of duplex ferrule fittings to our clients. These cater to the requirements of various industries and are known for dimensional accuracy, corrosion resistant and durability. Our range is available in various technical specifications as per the requirements of the clients. our range of alloy steel ferrule fittings is available in various specifications. These are sourced from renowned manufacturers, who utilize high grade material for manufacturing these. Best known for high tensile strength and durability, our range is offered at market leading rates to our clients. Our range of nickel ferrule fittings is procured from authentic vendors of the world. These are best in quality and conform to the international quality standards. Our range caters to the requirements of various industries and is known for optimum performance and high durability. Available in various grades, our rage can be further customized in terms of size, weight, thickness and dimension as per the requirements of the clients. Inconel & monel ferrule fittings hastelloy & titanium ferrule fittings alloy - 20 ferrule fittings copper alloy ferrule fittings. twin ferrule fittings s.s. Double ferrule fitting front ferrule nickel ferrule fitting.

• Brand Name: T.c fitting
• Material: Stainless Steel
• Finishing: Polished
• Feature: High Strength
• Type: Pipe Fittings
• Country of Origin: India
• Head Code: 400004

• Material: Brass
• Size: 1/4 inch-1 inch
• Color: YELLOW
• Bend: DEGREE
• Capacity: AS REQUIRED
• Item Code: AMTB24

Shasan Piping Solution is a main Manufacturers and Exporter of Pipe Fittings. We offer Pipe Fittings in various evaluations and material which are of predominant quality.We can supply stainless steel  Pipe Fittings and stainless steel funnels in an extensive variety of sizes and grades from our stockroom. These all channels and tubes are fabricated as per national and global gauges furthermore according to details of our clients. We supply funnels and tubes in extent 15 mm NB upto 1200 mm NB in Schedule 5S, 10S, 10, 20, 40S, 40, STD, 60, 80S, 80, XS, 100, 120, 140, 160 and XXS and are generally utilized as a part of mechanical applications.

• Country of Origin: India
• Type: Double Ferrule Tube Fittings

T-lok makes single and double compression tubes fittings which are designed / manufactured for process and instrumentation tubing which provides a leak proof torque free all the tubing connections, thus eliminating hazardous costly leaks. End connection : 1/16 to 1" (npt,bsp,bspt socketweld and plain end) working pressure 2000 to 6000 psi

Copper Fittings, Copper U Bend, SS 304 Steel U Bends, copper reducer

• Size: 1inch, 2Inch, 3/4Inch, 3Inch
• Thickness: 0-5mm
• Type: Fittings
• Uses: Used in preventing the nut loosening even under high strain and vibration
• Corrosion resistant: Yes
• Features: High Tensile Strength, Superior quality

We offer quality Ferrule Pipe Fittings. Three piece structure of these Ferrule Pipe Fittings at market leading prices. Ferrule Pipe Fittings includes body, special case hardened ferrule and a nut. These Ferrule Pipe Fittings have leak proof joints and can withstand extreme working conditions.