Hydraulic Shears Dealers in Mumbai

Ram & Table designed with inclined member and box type structure for maximum strength. Positive holding of Hyd. Hold downs avoids slippage of sheet during    cutting stroke. HCHCr Blade suitable to MS & SS. Hardened Transfer bars. Front gauging by disappearing stoppers mounted on front squaring arm.   SPECIAL FEATURES   The stable robust, all welded steel frame from ultrasonically tested plates are of top quality. Ramand table designed with special inclined member and box type structure for maximum strength. The top beam is guided by three point roller with replaceable hardened liners for least wear.This eliminates lubrication of guides. Roller guide made of hardened & ground bearing steel to provide better quality of cutting for a long time. Rake angle can be varied to permit shearing of higher thickness than nominal capacity and facilitating distortion free shearing of thin sheets. The fastest and easiest way of blade clearance setting without need of feeler gauge, which helps Burr-free edges. Positive holding by hydraulic holddowns before shearing avoids slippage of sheets and independent       operation of holddowns for clamping of sheet helps checking of mark without taking shear stroke. Front gauging by disappearing stoppers mounted on left squaring arm. Robust, heavy & accurateback gauging to set cutting width. Hydraulic cylinder are designed with both low and high pressure sealing, Hard chrome plated rod also with special type guide for long life without leakage. Hydraulic components of international quality assembled in our own factory with specially designed compact manifold   STANDARD ACCESSORIES   Main Drive motor Electric Control Panel Operational Console Pre selector switch to adjust rake angle   Lever operated blade clearance with calibration Fine stroke adjustment rod with limit switch Front sheet support  Squaring arm on right end with steel rule Hardened transfer bar mounted on table  Hold down cylinders   Shadow light Indicator Four edge HCHCR / HCSR blade interchangeable & suitable to shear mild and St. Steel Manual back gauge   OPTIONAL ACCESSORIES   Second squaring arm on left side Motorised back gauge with DRO NC back gauge with ball screw Front support with rolleraccording to required length Rear sheet support Ball transfer table Degree protector for angular cutting Stroke counter Design with throat depth First fill of hydraulic oil

Range : 3 mm to 25 mm Length : 1250 mm to 6000 mm   Ram & Table designed with inclined member and box type structure for maximum strength. Positive holding of Hyd. Hold downs avoids slippage of sheet during    cutting stroke. HCHCr Blade suitable to MS & SS. Hardened Transfer bars. Front gauging by disappearing stoppers mounted on front squaring arm.   SPECIAL FEATURES   The stable robust, all welded steel frame from ultrasonically tested plates are of top quality. Ram and table designed with special inclined member and box type structure for maximum strength. The top beam is guided by three point roller with replaceable hardened liners for least wear.This eliminates lubrication of guides. Roller guide made of hardened & ground bearing steel to provide better quality of cutting for a long time. Rake angle can be varied to permit shearing of higher thickness than nominal capacity and facilitating distortion free shearing of thin sheets. The fastest and easiest way of blade clearance setting without need of feeler gauge, which helps  Burr-free edges. Positive holding by hydraulic holddowns before shearing avoids slippage of sheets and independent       operation of holddowns for clamping of sheet helps checking of mark without taking shear stroke. Front gauging by disappearing stoppers mounted on left squaring arm. Robust, heavy & accurateback gauging to set cutting width. Hydraulic cylinder are designed with both low and high pressure sealing, Hard chrome plated rod also with special type guide for long life without leakage. Hydraulic components of international quality assembled in our own factory with specially designed compact manifold     STANDARD ACCESSORIES   Main Drive motor Electric Control Panel Operational Console Pre selector switch to adjust rake angle   Lever operated blade clearance with calibration Fine stroke adjustment rod with limit switch Front sheet support  Squaring arm on right end with steel rule Hardened transfer bar mounted on table  Hold down cylinders   Shadow light Indicator Four edge HCHCR / HCSR blade interchangeable & suitable to shear mild and St. Steel Manual back gauge OPTIONAL ACCESSORIES   Second squaring arm on left side Motorised back gauge with DRO NC back gauge with ball screw Front support with rolleraccording to required length Rear sheet support Ball transfer table Degree protector for angular cutting Stroke counter Design with throat depth First fill of hydraulic oil    

• Voltage: 220 - 240 V
• Payment Terms: T/T (Bank Transfer)
• Automatic Grade: Manual
• Max Shear Thickness: 2-3 mm
• Power Source: Hydraulic

Hydraulic Variable Rake Angle Shears, Bolt Making Plant, Milling Machine

hydraulic crop shear, scrap winder unit

Hydraulic weld shear, AT Welding, ms rail roller, USFD Testing of RAIL

Hydraulic Swing Beam Shear, Busbar Cutting Machine