Industrial Dryers Dealers in Midc, Mumbai

• Features: Main Body/Vacuum chamber thick SS 316 plate with heavy duty SS 316 flange and stiffeners.Trays in SS 316 rounded corners and edges.Silicon transparent gasket for door.
• Optional: Hot water system (steam heated) with MS tank (insulated), SS 304 steam radiator/electrical heaters,
• Finishing: Internal 320 grit mirror polish and outer 180 grit mat finish.

We are offering rotary louvre dryer. We are well known manufacturing and supplying company of rotary louvre dryer. Special features: high thermal efficiency - continuous operation - compact installation

The  Rotary Dryer is a type of industrial dryer employed to reduce or minimize the liquid moisture content of the material it is handling by bringing it into direct contact with a heated gas. The dryer is made up of a large, rotating cindrical tube, usually supported by concrete columns or steel beams. The dryer slopes slightly so that the discharge end is lower than the material feed end in order to convey the material through the dryer under gravity. Material to be dried enters the dryer, and as the dryer rotates, the material is lifted up by a series of internal fins lining the inner wall of the dryer.When the material gets high enough to roll back off the fins, it falls back down to the bottom of the dryer, passing through the hot gas stream as it falls. This gas stream can either be moving toward the discharge end from the feed end (known as co-current flow), or toward the feed end from the discharge end (known as counter-current flow). The gas stream can be made up of a mixture of air and combustion gases from a burner, in which case the dryer is called a direct heated dryer. Alternatively, the gas stream may consist of air or another (sometimes inert) gas that is preheated. When the gas stream is preheated by some me where burner combustion gases do not enter the dryer, the dryer known as an indirect-heated type. Often, indirect heated dryers are used when product contamination is a concern.Available Capacity  : 100 Kg/hr. to 1000 Kg/hr.Available M.O. : M.S. , S.S. 304, S.S. 316, S.S. 316 L etc.

An Air Tray Dryer Is used for the best drying results in conventional process. It consists of a double-walled cabinet with one or two doors. The gap between two walls is filled with light resin-bounded fibreglass wool insulation material to avoid heat loss. The doors are provided with gaskets to avoid air leakages from the front side of the door. Stainless steel trays are placed inside the chamber. cGMP model dryers are designed to dry specific products.

Microwave Dryer is the best suited technology for industries related to pharmaceutical formulations. Thus people are highly preferred this technology over others. Rufouz Hitek Engineers prepare such Microwave Dryer System which can go well with your manufacturing specifications. The term microwave itself refers to the frequency which lies in the electromagnetic radiation. They are the most commonly used technique that used in our day to day lives. Drying is one of the operation where a big amount of energy is needed for changing the phase. Heat in the microwave is generated through the interaction between the microwave and the part where electromagnetic energy is degenerated.

FUNCTION  Used mainly for drying of high grade, temperature and oxygen sensitive products. Highly suitable for drying hygroscopic substances, which are dried to very low residual moisture, content level. Frequently vacuum drying cabinets are the sole possibility for drying lumpy, glutinous products or products of low pomposity. CAPACITY Standard models range from 4 trays to 48 trays. SALIENT FEATURES Bodies may be of cylindrical or rectangular cross section. Both shelves and body are heated (the body to prevent internal condensation) with controlled circulation of hot water, steam or dia thermic fluid. Vacuum is drawn through large diameter ducts to minimize pressure drops and produce minimum working pressures. Both rotary and static dryers can be supplied with the following Optional ancillaries. Heater system for either pressurized hot water or dia thermic fluid. Cyclones and sleeve filters for powder recovery (for rotary dryers) Solvent recovery system with condenser and receiver, vacuum pump and ancillaries, characteristics and dimensions depending on the drying processes. Vacuum Tray dryer is the most commonly used batch dryer. They are box-shaped and loaded and unloaded via a door (two doors on the larger models). Inside are several heating plates mounted one above the other on which the product is placed in trays. The bottoms of both heating plates and trays should be as smooth as possible to permit optimal heat transfer between plates and product. The medium flowing through the heating plates is water, steam or thermal oil.     The distance between the heating plates is determined primarily by the surface loading and the foaming of the product. To void retrograde condensation the cabinet walls are indirectly preheated by the heating plates. Next, the product is introduced and heated at atmospheric pressure. Only after all individual product trays reach the same temperature the cabinet is evacuated and drying can start. The  preheating phase is very important in order that the drying curve and the foaming of the product is identical throughout the cabinet. During the main drying phase the vacuum is in the range of 40 to 80 mbar abs and in the final drying phase vacuums of only few mbar abs are reached. Heating temperatures are normally in the range between 800C and 1100C. Depending on product and surface load, drying takes from a few hours to 1 to 2 days. For some products the vacuum and temperature profiles are automatically controlled in order to prevent a pass over of the critical product temperature. factor in the design of drying cabinet systems. If for example vigorous foaming of the product is desired, evacuation to the operational vacuum level must take place very quickly. Vapors produced during drying are taken out direct, or via a steam jet compressor to a surface condenser in which the vapors condensate. The non-condensable vapors are extracted by the vacuum system. On completion of the drying, the product can be cooled by circulating of cooling water through the heating plates. Features: All contact parts are made out of SS304 / SS316 / SS316L quality material in GMP models and mild steel externals with stainless steel internals in standard model Hollow pad type heating shelves which are easily removable for maintenance Condenser and condensate receiver fixed on the dryer body or stand alone for remote installation Full welded skirt on vacuum dryer body for flush mounting through the wall. External fluid heating of dryer with protective panels in stainless steel or mild steel powder coated. Dedicated fluid heating and circulating systems. These can be steam or electrically heated. Fluid heating systems are available for water as well as thermic fluid (for temperature requirements above 95 oC) Validation ports and nitrogen purge nozzles Can be designed to customers specification requirements Steam sterilisable models available Double door loading available for large models Halar lined internals for corrosive applications

General Specification: Construction : External : 2 mm  Thkinternal : 2 mm Thkmoc : cGMP  Surface Finish : External : Buffed to 150 grit matt finish Internal : Buffed to 220 grit mirror finish.  Inlet & Outlet : All dryers have a 5 micron pre filter r at the inlet and a manually infinite adjustable damper at the outlet. Door : Doors at provided at the front and / or rear side of the tray dryer. Door lips are lined with silicon rubber gasket to prevent any leakages. Suitable locking is provided for the doors. Air Circulation : Air circulation is done by specially designed recirculation blowers inside the tray dryer. The blower capacity, static & design depends on the size and model of dryer. Heating : Dryers are normally supplied with either steam/ electric/ thermic fluid / hot water heating system. Suitable heating coils / caloriefiers are provided in the dryers. Temperature Control : Temp control system is done by electronic digital temp controller fitted in the control panel. The temp control in the dryer is fully automatic. Trays : Trays are available in S.S. 304/ 316 q. All trays are fully die pressed and with cooved corners. Trays are buffed to mirror finish. Trays are also available in aluminum / Polypropylene / Frp/ M.S. galvanized as per clients requirements. Trolley : Trolley is provided in the dryers to accommodate trays in it. Trolley truck are used to load and unload the trays into the dryer. Control Panel : Automatic Control panel is fitted on the side of the dryer. If consists of Starters, contactors, safety relays, ckt breakers, indicating lamps, push buttons , timers, controllers etc.

• Gross Capacity: 500 Ltrs. To 25000 Ltrs
• Vacuum: Upto even 0.6 torr
• Heating Temperature: 30° to 300°C.

Rotary Vacuum Paddle Dryer is a jacketed cylindrical horizontal vessel with a a large diameter hollow shaft. Attached to the shaft are hollow paddles provided with specially designed scraper blades, which scrape the entire internal surface of the Dryer and continuously move and rotate the material thereby precluding the possibility of material remaining in contact with hot surfaces for protracted periods of time.

A well known rotary vaccum dryers supplying company.

VACUUM TRAY DRYERS, double cone vacuum dryers, Conveyor Idler, Tunnel Dryer

• Brand Name: RIDDHI
• Material: SS AND MS
• Model: RDVTD
• Capacity: 3,6,12, 24, 48,96 TRAYS
• Temperature (Degree Celsius): 40 TO 110 DEGREE
• Design: MECHANICAL
• Weight (kg): 4 TO 5 TONS
• Number Of Shelves: 16
• Voltage (V): 410 VOLTS
• Automation Grade: Automatic
• Usage/Application: VACUUM DRYING

• Certification: MANUFACTURERS
• Condition: New
• Cleaning Type: WATER REMOVAL
• Use: DRYING OF STRANDS
• Power(W): 0.25 KW TO 11.0 KW
• Supply Ability: 30 Unit/Units per Month
• Machine Type: Other
• Packaging Details: CARD BOARD BOXES
• Model Number: STRANDS DRYING AIR KNIFE SYSTEM
• Material: METAL/RUBBER
• Industry Used: PLASTIC
• After-sales Service Provided: No overseas service provided
• Brand Name: RAICO

We are engaged in manufacturing high grade Vacuum Tray Dryer in various shapes and sizes. Our Vacuum Tray Dryer is aptly designed for drying thermal sensitive materials which can be easily resolved, degrade, or polymerized under high temperature. Sterilization of the material can be conducted before drying process as no other materials are allowed to enter once the dryer is started. Besides, it also assists in elimination of configurationally damage of drying materials. Optional : Receiver and Condenser in SS 316SS 304 steam radiator/electrical heatersValidation port is available with CensorsSkirting or wall panel that is provided with all along the body as well as vacuum chamber flangeHot water system (steam heated) with MS tank (Insulated)Insulation is provided with vacuum chamber outer surface excluding door. The insulation is enclosed and is covered with transferable SS 304 panelsCirculation pump with FLP Motors and controlsVacuum Pump (2stage water ring) consisting FLP motor Salient Features : Main Body made of thick SS 316 plateDoor thick SS 316 plate consisting heavy duty SS 316 flangeHeavy duty SS 316 flange and stiffeners availableTrays (without back folding) in SS 316 having round corners and edgesCondenser and Receiver SS 304Hollow type pads shelves with SS 316 Sheet as well as BafflesDigital Temperature controller (FLP) withExplosion Vent or rupture disc on vacuum chamberValidation Port on Body (provisional)Solenoid controlled Pneumatic operated valve located at hot water inletDigital type Vacuum gauge in vapor lineDigital Temperature Indicator at H.W. inlet & outletPressure release valve in steam lineDigital Temperature Indicator (FLP) in vapor lineSilicon Transparent gasket perfectly designed for doorLight glass provided on vacuum chamber body, door and receiverDrain valve for Vacuum chamber as well as ReceiverNitrogen purging valve and Vacuum break valve available on vacuum chamberFinish : Internal 320 grit Mirror Polish /outer 180 grit mat finishTemperature Accuracy : plus-minus 2 to 3 degree

Italimpianti produces a wide range of gas atomizers specially designed for the production of metal powders, available in small size to be used in the laboratory until you get to large installations for a real industrial production. The special geometry of the nozzle allows a constant production of metal powder with a spherical form of high quality, with controllable size from 10 to 100 microns. All our melting furnaces are equipped with special induction coils, powered by generators completely designed and manufactured inside our company, with capacities from 5 to 20 kW. The fusion process can take place in air or in a controlled atmosphere, as well as under vacuum or at normal atmospheric pressure, thus allowing a wide range of atomizzabili metals, including those low melting or easily oxidizable. The chemical composition and the homogeneity of the alloys are perfectly guaranteed through the use of low-medium-frequency generators, while the use of inert gas inside the upper chamber limits the oxygen content. These systems are designed to ensure a quick replacement of the crucible, to avoid "cross-contamination", they are easy to clean and easy to use. TECHNICAL CHARACTERISTICS: • Power consumption: from 5 kW to 20 kW • Production Capacity: from 1 to 10 Kg per cycle • Metals that can be treated: Steel, Precious Metals, Copper, Zinc, Aluminum and other base metals, including alloys .    

• Features: The dryer due to its closed design reaches the preset temperature fast, Specially designed blower facilitates in even distribution of the hot air inside the chamber.
• Pay Mode Terms: L/C (Letter of Credit)
• Size: 12 T
• 24 T: 48 T
• 96 T: No. of Trays
• 12: 24
• 48: 96
• Motor – Blower (HP): 0.25
• 0.5: 1
• 1.0x2 Nos.: Electrical Heater (k.w.)
•  :  
•  :  
• Upto 100 0C: 3
• 6: 9
• 15: Upto 200 0C
• 6: 9
• 15: 21
• Upto 300 0C: 9
• 12: 21
• 27: No. of Doors
• 1: 1
• 1: 2

• Tray Size: 16 x 32 x 1.25 (h)
• Tray height: 2 inches

All stainless steel 304 316 316L CGMP or mild steel externals with stainless steel internals (vapor and product contact parts), Hollow pad type heating shelves which are easily removable for maintenance, Condensor and condensate receiver fitted on the dryer body or stand alone for remote installation Fully welded skirt on vacuum dryer body for flush mounting through the wall, External insulation of dryer with protective panels in stainless steel or mild steel powder coated Dedicated fluid heating and circulating systems. These can be steam or electrically heated. Fluid heating systems are available for water as well as thermic fluid ( for temperature requirements above 95 degree centigrade ), Validation ports and nitrogen purge nozzles. Can be designed to customers specific requirements, Steam sterilisable models available, Double door loading available for larger models

Drying solutions to produce cereal based baby foods (weaning foods), drink cereals, brewers yeast, fruits & vegetables, milk powder (for chocolates, gulab jamun & other Indian sweetmeats), also lines for making potato flakes / potato granules, maleic anhydride, phthalic anhydride, etc 

seed dryers, chemical process equipments, Food Processing Equipments

Double Drum Dryer

air tray dryer, Nitrous Oxide Gas Plants, Agitated Cylindrical Vacuum Dryer

spray drying plants, film evaporators, Evaporators

Double Drum Dryer

Industrial Refrigeration Air Dryer, cooling tower maintenance service

spin flash dryers, Blender, tumbling dryer, Vessels

Industrial Dryers, Dishwashers, dish washers, Water Purifiers

Vacuum Tray Dryer, High Shear Mixer, vacuum transfer system, air tray dryer

rotary vacuum cone dryers, halar coating, etfe coating, pvdf coating

Vacuum Tray Dryer, Fluid Bed Dryers, pharmaceutical packaging machines

Centrifugal Dryer, Heat Exchanger, REACTOR, Used Chemical Machinery

drum drier, Oil Filters