Back Back
oil injectors
The pressure required to dismount bearing assemblies generally is in the 200 to 500 kgcm2 range; and for torque-transmission joints is in the 800 to 1800 kgcm2 range. It is only in exceptional cases that a pressure of 2500 kgcm2 is required.
Pressure : 2500 kg/cm2
...more
Induction Heating Equipment
Inventum Induction Heater Model HIR-2540 is specially designed to dismount and mount the Inner Races of Cylindrical Roller Bearings used on the Axles of Railway Rolling Stock and in Traction Motors. The equipment can also be used for similar applications by other industries.When a job is heated with the induction coil it acquired magnetism strong enough to attract iron particles, iron dust etc. To deal with this phenomenon, it is necessary to eliminate the residual magnetism after heating. The design of Inventum Induction Heater Models HIR-2540 permits fast demagnetisation by use of the heating coil itself. The Induction Coil can be used for demagnetisation as well as heating.
...more
Induction Heaters
Its controls are microprocessor based. It weights about 47 kg. and can be easily carried to the site of operation, using special die-cast handle provides on both sides. It can heat a typical bearing of 13 kg. to 100oC in 3 minutes. HIB-02 consists of the main body Induction Heater and a separate handheld HIB Control Box. This HIB Control Box is connected by a 2 meter long cable to the unit and hence the unit can be operated from a convenient location.
...more
Induction Coils
flows through a coil wound around a component, it creates an oscillating magnetic field which induces current in the component. The magnetic field takes the path of least resistance and also due to the skin effect, the outer periphery of the component gets heated more rapidly than the core.
...more
induction bearing heater
Induction Heater Model 'HIB-04' is the latest addition to the range of 'HIB' Series Induction Heaters manufactured by Inventum. For over a decade Inventum has been supplying 3 models i.e. 'HIB-01' (3-3.5 kVA), 'HIB-02' (6-8 kVA) and "HIB-03' (11-13 kVA) to the industries. Keeping in view the special requirement of a few important customers, Inventum has now developed the Model 'HIB-04' (22-25 kVA unit) to heat larger size bearings and other components having mass upto 600 kgs.
...more
hydraulic tools
Developed a unique concept as Mobile Workstation to dismount direct mounted bearings without any damage or scoring to the bearing bore or shaft seating, with minimal force. This equipment is specially designed to inject oil under high pressure between the bearing bore and shaft seating, enabling the bearing to be pulled out floating on thin film of oil.
...more
bearing induction heater
Its controls are microprocessor based. It weights about 47 kg. and can be easily carried to the site of operation, using special die-cast handle provides on both sides. It can heat a typical bearing of 13 kg. to 100oC in 3 minutes. HIB-02 consists of the main body Induction Heater and a separate handheld HIB Control Box. This HIB Control Box is connected by a 2 meter long cable to the unit and hence the unit can be operated from a convenient location.
...more
Bearing Heater
In HIB-01 the 2 operating modes, viz. Temperature mode and Time mode, are controlled through separate knobs on the Control Panel. These modes are connected in series, and heating cycle stops when either of the modes reaches its preselated value first.HIB-01 can also be used to heat bearings of larger diameter. For this purpose a pair of Raiser Blocks (size 55 x 55 x 120 mm ) are to be used. The unit can also be used to heat up a plate of any magnetic material by placing the plate in place of the horizontal yoke across the 2 vertical supports.
...more
bearing fitting tool kit
TIK is the right equipment for mounting small size bearings. The Tool Kit is specially designed to avoid damage to bearing rings while being mounted. The correct combination of Impact Ring and Impact Sleeve will ensure that the mounting forces are evenly distributed over the bearing rings and hence the risk of misalignment and damage to the bearing is eliminated. A nylon - head hammer must be used for impact blows.
...more
industrial induction heater
Inventum Induction Heater Model HIR-2540 is specially designed to dismount and mount the Inner Races of Cylindrical Roller Bearings used on the Axles of Railway Rolling Stock and in Traction Motors. The equipment can also be used for similar applications by other industries.When a job is heated with the induction coil it acquired magnetism strong enough to attract iron particles, iron dust etc. To deal with this phenomenon, it is necessary to eliminate the residual magnetism after heating. The design of Inventum Induction Heater Models HIR-2540 permits fast demagnetisation by use of the heating coil itself. The Induction Coil can be used for demagnetisation as well as heating.
...more
Reviews & Ratings
Write a ReviewBe first to Rate
Rate This
Share your Correspondence Details to receive messages from INVENTUM ENGINEERING COMPANY PVT. LTD
Post Free Ad