Isolation Transformers Dealers in Mulund, Mumbai

• Min. Order Quantity: ,

We bring forth Control Circuit Transformer with basically electric components fitted on the Circuit boards which are then fitted in the Junction boxes and are used in the monitoring of the current passed on to the Oil pipelines, Tank farms and Oil wells to avoid disruption of the flow of the Oil and Gas. A Control Circuit Transformer is a device designed to provide a reduced control voltage for energizing the coils of electromagnetic devices such as motor starters, contactors, relays, & electronic circuits. These devices make up the majority of the loads supplied by the Control Circuit Transformer. Control Circuit Transformer is also referred to as Industrial Control Transformers, Machine Tool Transformers, and Control Power Transformers, Inrush Volt-Ampere & Sealed Volt-Ampere considerations. The proper size, or the VA rating, of the Control Circuit Transformer is important. It will be a determining factor in the life of the transformer, which ultimately will reflect on the proper operation of control devices that it supplies.  Methods of Selecting The methods of selecting transformer VA ratings addressed in this technical paper are applicable to 50-3000 VA. Control Circuit Transformer. The transformers used in this application fall into the dry type insulation category. Typical primary voltages are 600, 480, 240, and 110. Transformers can also be manufactured with special primary & secondary voltage combinations. There are two VA values to be considered when selecting a transformer. Energizing electromagnetic components creates a large momentary surge current, commonly referred to as inrush VA. This is the first VA value to be considered. The inrush VA will last approximately 5-20 milliseconds and can have a value as high as ten times the transformer's nameplate rating. Thus, the inrush VA will be high in value and short duration. A properly selected control circuit transformer is designed to handle the momentary inrush VA and at the same time maintain a secondary voltage within a set range. The second value to be considered is the sealed VA, the amount of volt-amperes required to maintain the energized state of an electromagnetic device. This VA requirement will be 5 to 10 times less than the inrush VA.Specifications Range : 1mA to 20 A Taps : As per client spec. ( We are also provided PCB with connector) Shielding Lamination : CRGO or CRNO Input : 110/230/440V AC

• Phase: Single & Three Phase
• Cooling Type: Dry Type/Air Cooled
• No. of Winding: Double Winding
• Application: Power, Electronic, Instrument, Lighting, Rectifier, Audio
• Input Voltage: 400- 450 V
• Insulating Fluid: Mineral Oil

We are offering transformer. Double wound, step-down transformer made from high quality annameled dpc copper wire of circular & square cross selection & having crgo lamination as core. Transformer core is cylindrically designed to overcome losses and achieve maximum efficiency high packing fraction enables compact transformer design & reduces heating in high load condition ballast choke is single wound inductor made of crno lamination &anameled copper wire set to perfection to controll current & voltage drop at perticular current load. Setting only possible at factory.

• Power: Electric
• Phase: Two phase
• Cooling Type: Oil Cooled
• Material: Stainless Steel
• Usage: Industrial
• Single Coil Current: 1-150 amp
• Ganged Coil Current: 150 amp
• Minimum Order Quantity: 1 Piece

All the types of electrical noises, predominantly common mode noises can be eliminated by Ultra Isolation Transformers. Since it isolates primary and secondary or separates neutral to ground bond on the secondary side, can be used to create separately derived source to combat current loops. The Ultra Isolation Transformers are available in different levels of noise attenuation capabilities. The most commonly used are 100 & 120 dB. The coupling capacitance between primary and secondary is direct 1:1 relationship with dB levels. Some of the graphs herewith indicate different types of electrical noises observed in typical Engineering Industries & successfully eliminated.

We have good expertise in designing Ultra Isolation Transformer. These noise cut off transformer is compact in design, cost efficient and perform with musical perfection. The noise cut-off Ultra Isolation Transformers thus eliminate noises from high frequency and attenuates the spikes to negligible values. This way these protect from such kind of electrical disturbances.

We are manufacturing & supplying a wide range of ultra isolation transformer in mumbai. All the types of electrical noises, predominantly common mode noises can be eliminated by ultra isolation transformers.

• Type: Control Transformers
• Color: Green, Grey, Light Green, Sky Blue
• Application: Equipments Controlling
• Condition: New, Used
• Automatic Grade: Automatic, Fully Automatic
• Cooling System: Air Cooled, Oil Cooled
• Warrenty: 1yr, 2yrs

K Rated Isolation Transformer, Ultra Isolation Transformers

We are offering Neelkanth Power Solutions is a widely prominent and popular name in the field of manufacturing and supplying varied range of isolation stabilizer in India.

Instrument Transformers, Copper Cable Lugs, Cooling Fans, Cable Glands

Double Wound & Auto Wound Transformer, Copper Carbon Brushes

As an Ultra Isolation Transformer, Unity’s Tranquil is the most powerful solution to help eliminate all types of noise, particularly Common Mode Noise, Spikes, Surges and Transient Noise, which act as silent killers inside factories and commercial parks alike.

CONTROL TRANSFORMERS, Battery Chargers, electronic rectifiers

Distribution Transformers, Electrical Panels, Switchgears

CONTROL TRANSFORMERS, dc filter chokes