Kevin Enterprises Private Limited Andheri East, Mumbai, Maharashtra

KEVIN ME-II Wire Mesh Packing has enhanced self-wetting characteristics; as the fiber is woven from fine diameter wires. The packing element consists of parallel-perforated corrugated sheets of wire mesh. These packings are particularly suited in separations that require a large number of separation stages, which typically operate under high vacuum and therefore low liquid loads. The capillary action of the wire mesh ensures complete surface wetting when complemented with high efficiency internals. KEVIN ME-II Wire Mesh Packing is available in following two types:

Trays are used in mass transfer operations where pressure drop limitations are not critical. They are mainly used in high-pressure distillation operations. However, there are a few atmospheric, moderate pressure and vacuum operations where trayed towers are used. Trays are availabe in segmental or cartridge type construction to suit customer's requirements. Our design team is well experienced in Tower rating and can select or advise you on the type of tray most suitable for the given conditions. Design of each type of tray is done judiciously by selecting the right type of valve, cap, hole diameter, etc.

Medal-Pak ( formerly sold as Norton's IMTP® ) gives the best of both worlds in terms of performance (i.e. low-pressure drop and high efficiency). It can be effectively used in both high pressure and vacuum towers. Other advantages include large effective interfacial area, high mechanical strength, and low cost. Its monolithic construction overcomes the problem of "opening out " at the ends as can be experienced with ring-shaped packings. Medal-Pak is available in an array of sizes to provide multiple combinations of efficiency and pressure drop. Medal-Pak can be fabricated from a variety of metals including, but not limited to, Carbon steel, Stainless steel, Copper, Aluminum, Titanium and Zirconium.

Liquid distributors aim towards ideal liquid distribution, i.e. equal liquid rate per unit area of the packed bed surface. These distributors are available in a complete range to suit various column diameters, liquid rates and service conditions. Models, which can give turndown ratio upto 10:1, are available. Our design team selects the most suitable model for a given application. Distributor With Flow Multiplier, Distributor Pan Type, Distributor Pipe Arm Type, Distributor Riser Deck Type.

Tierce Rings are also ring type packings but with an approximate diameter to height aspect ratio of 3:1 and are further flared along the periphery for strengthening of packing.

Support plates in addition to providing physical support to the packings, must also allow unrestricted flow of gas and liquid. Gas injection support plates provide separate passageways for liquid and gas, which minimizes the pressure drop across the plate. Support plate model is selected depending upon the packing type and size and the maximum design load to be supported.

Super Saddles are the improved version of the original saddles. They are designed to give the enhance internal gas and liquid distribution. The unique scalloped edge is the key to the product's high performance in terms of higher capacity and improved rates of mass transfer when compared to traditional plastic saddles. It also serves to overcome the problem of nesting that is commonly encountered with ordinary saddles. These saddles are available in plastic & ceramics both. Plastic Super Saddles are used where temperature are less & services is corrosive. Ceramic saddles are used where temperature required are high along with chemical attack resistance these saddles are offered with a glazed construction to enhance the capacity and reduce porosity

Super Saddles are the improved version of the original saddles. They are designed to give the enhance internal gas and liquid distribution. The unique scalloped edge is the key to the product's high performance in terms of higher capacity and improved rates of mass transfer when compared to traditional plastic saddles. It also serves to overcome the problem of nesting that is commonly encountered with ordinary saddles. These saddles are available in plastic & ceramics both. Plastic Super Saddles are used where temperature are less & services is corrosive. Ceramic saddles are used where temperature required are high along with chemical attack resistance these saddles are offered with a glazed construction to enhance the capacity and reduce porosity

Pall rings, Medal-Pak ( formerly sold as Norton's IMTP® ) gives the best of both worlds in terms of performance (i.e. low-pressure drop and high efficiency). It can be effectively used in both high pressure and vacuum towers. Other advantages include large effective interfacial area, high mechanical strength, and low cost. Its monolithic construction overcomes the problem of "opening out " at the ends as can be experienced with ring-shaped packings. Medal-Pak is available in an array of sizes to provide multiple combinations of efficiency and pressure drop. Medal-Pak can be fabricated from a variety of metals including, but not limited to, Carbon steel, Stainless steel, Copper, Aluminum, Titanium and Zirconium.

Omni-Pak (formerly sold as Snowflake® ) is a high-performance plastic packing. It offers superior efficiency and capacity in environmental application such as scrubbing and stripping. Its distinctive shape lowers the pressure drop, which significantly reduces energy consumption. Its various applications include ASU, DCA, fume scrubbing, acid gas absorption, VOC stripping, wastewater treatment, flue gas scrubbing, etc. It gives higher efficiency compared to Pall Rings 38 mm (1.5 inches) and larger as well as #2 Plastic Super Saddles and larger.

KEVIN is also in a position to offer tower internals i.e. bed limiters, distributors, support plates, etc. in a variety of polymer materials including FRP, polypropylene, CPVC and PVDF. These internals are designed to provide optimum performance and operating conditions. Major advantages of plastic internals are their lightweight construction and chemical resistance in turn leading to extended life of internals.

Mist eliminators, Effective separation of vapor and liquid is a primary requirement for efficient industrial processing. KEVIN Mist Eliminators are engineered to provide high efficiency & low pressure drop for effective separation.

Effective separation of vapor and liquid is a primary requirement for efficient industrial processing. KEVIN Mist Eliminators are engineered to provide high efficiency & low pressure drop for effective separation. KEVIN Liquid-Liquid Coalescers solve separation problems involving immiscible liquids.

Liquid-Liquid Extraction is a Separation process in which a feed stream containing dissolved components is contacted with an immiscible solvent which forms a second liquid phase and selectively extracts the dissolved components from the feed. It is primarily used for services where distillation is not practical, like close boiling point or heat sensitive materials. Packed columns in LLE are used in certain extraction services, such as alcohol washing and contaminant removal from light hydrocarbon. Packed columns are flexible and can handle wide range of feeds and extract to feed ratio. Packed columns are equipped with internals like Disperser PlateDisperser cum Support Plate, Feed pipes for Dispersed and Continuous Phase. Packing promotes, contacting of two phases, as they have to follow tortuous path thru packed bed. It brings both the phases in close contact, maintaining dispersion & preventing short-circuiting.

Different Feed devices are available for various feed conditions of the fluid entering the column such as only liquid feed, mixed feed or gaseous feed. Feed devices are selected to complement with the type of Distributor used to give the optimum performance.

Fatty acid distillation plant has been designed & installed to achieve desired product purity & quality at a minimum cost and also to take care of variations in input feed composition.

Collector trays are used to collect liquid from between packed beds or packed bed to tray transition. Liquid interception is required in various situations such as total or partial draw-off of liquid etc. Different types of collector trays are available to suit the vapor and liquid rates

Bed limiters are safety devices that are available for both random as well structured packing to avoid the expansion of the packed bed, as well as to maintain the bed top surface level.