Laboratory Mill Dealers in Mumbai

• Power:  220V/50Hz
• Weight:  50Kg
• Grinding Chamber: Designed Volume: 400ml Effective Volume: 200ml
• Inner Chamber material:High wear resistant hard alloy 9CrMo18: Outer Materia: SS304
• Grinding pin and rotor material:High wear resistant hard alloy 9CrMo18: Cooling Mode: Cooling water passing through gridning chamber
• Mechanical Sealing: Self design mechanical seal. Sealing Support : SS304
• Dispersion & Grinding: ROOT patented turbine and pin type rotor. Dispersing linear speed：10.2 m/sec
• Separating mode: Dynamic separation; no stuck and high efficiency
• Grinding Media: 95% zirconia beads Zirconia beads spec : Dia 0.4 mm- Dia 1.4mm Filling quantity recommended：50% ᷉ 90%
• Dimension: 540(L)x 190(W)x240(H)mm  

• Power: 1-3kw
• Driven Type: Electric
• Warranty: 1yrs
• CFM Required: 20
• Required Power (HP): 7.5
• Capacity (KG/HR): 0.1 - 0.8

r & d model or qualifying model emco has designed this new and compact lab model for r & d purpose and also it acts as a qualifying model for the higher size production models. the latest designed computational fluid dynamics (cfd) is a branch of fluid mechanics that uses numerical analysis and data structures to solve and analyze problems that involve air flows. computers are used to perform the calculations required to simulate the interaction of carrying medium with surfaces defined by boundary conditions. this subsequently improved geometry of the milling chamber and ring integrated nozzles have led to a very narrow psd (particle size distribution). documentation to support fda validation design qualification (dq) operation qualification (oq) factory acceptance test (fat) installation qualification (iq) performance qualification (pq) features of jet mill - emco psi lab narrow particle size distribution (psd) simple and rapid assembly or disassembly limited number of components low energy consumption sterile manufacturing no heat generation no cross contamination variety of available liners to resist abrasion benefits for the cosmetics industries ultra-fine loose and compact powders improved metallic pigments effect perfect skin adherence increased binding effect ultraviolet radiation reflecting properties

Specific Engineering Corporation offers complete range of 2 roll mills for processing wide application rubbers, such as sheeting mill, worming mills,feeding mills, compounding mills, cracker mills, refiner mills etc. In general, the mills are study construction to match the heavy duty operation of rubber processing in tyre as well as non-tyre industries. The mills, fully assembled andd tested prior to dispatch stand on a robust steel structure base frame, precisely machined for accurate alignment. The mills are available in both Bull Gear as well as UNI Drive design. The bearing are provided with force feed oil lubrication or grease lubrication system with special seals to prevent ingress of deleterious particle. The rolls are ground chilled cast iron, with about 500 bhn hardnes. The rolls are of core design / peripherally drilled rolls or grooved rolls for cracker mill based on the requirement. The gear boxes are of unique design and of reputed make, specially manufactured to serve their purpose. SEC offers a wide range of mills right from smallest 6" x 13" LAB milll to 26" x 84" robust UNI DRIVE mills.Back roller is directly connected with reduction gear box by Oidha's coupling and power is transmitted to the front roller through connecting (couple) gears, there by omitting ordinary large bull gear pinion gear gear and pinion stand. This results in lower maintenance and quieter operation as well as better transmission efficiency ( Reduced power consumption). The rare roll and front can be made inter changeable to reduce roll inventory on request.The reduce the vobration i the main body, reduction gear and motor are mounted on the common bed which is supported by wedge shaped special level mounts (vibro mounts). The set position and size of level mounts are such that the wt. is evenly distributed on each level mount at an average of 5 kg/cm2. The level mounts require no foundation bolts, consist of 3 pieces of wedge with distinctive shock absorbers & are freely adjusted up to 12mm in height by a spanner. Thi faciliates erection, alignment & leveling and also movement of mill from one location to the other.   This mill is comfortable to work on far an average height person.There is minimal maintance and power consumption.One set of knife is provided in the front roll of th emill for sheet sutting.Stock blenders are provided on request.

Laboratory Mill, lab homogeniser, Platelet Agitator

Laboratory Mill, mixer granulator, Co Mill, Conta Blender, Co-Mill

lab two roll mill, PVC Compounding Mixers & Coolers