Mica Band Heater Dealers in Andheri, Mumbai

Being a reliable Manufacturer, Exporter and Supplier, we offer high quality Mica Band Heater. Our Mica Band Heaters are primarily designed for normal heating performance at a working tern of 450°C. With these heaters, the level of performance is achieved from a mineral known as mica. Our Mica Band Heaters are designed with close ends so as to protect them against contamination. This also enables its installation without causing any internal damages. The outer sheath of these heaters is constructed in stainless steel and brass, with various terminal options. We can manufacture these heaters in different diameters, watts, and volts, as per your specification. Benefits Low temperature capabilityLong service lifeLow energy costHeat transfer not affected by surface and can be easily installed and removed Application Barrels and dies of InjectionBlow Molding MachineExtrudersAutoclaves & Chemical Reactors

EXCEL’s Mica Band Heaters are widely used to heat the molds, dies,  nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machinery The mica heater is most economic It provides excellent thermal conductivity as heat transfer is by “conduction” Due to its best heat transfer capability, faster heating up & cooling down is possible Maximum sheath temperature upto 480°C (900°F) Maximum watt density = 25 watts/square inches Note: In case where high watt densities are require, it is important that All  heaters should be used with appropriate, approved and precise  temperature control/sensor device(s) The built in insulation is specially formulated for the excellent heat  reflection &performance capabilities The low mass heaters give the best controllability. The lower the thermal  mass, lesser time required to deliver the heat to the object to be heated.  Due to low mass and high conductivity, the“Polymer Melt” is heated  quickly. Resulting autotune function on a control works best. Flexible one or two – piece design makes installation faster & easier . Its  flexible construction also allows the heater to be opened to the full  diameter of the cylinder The most common square, rectangular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or terminals EXCEL’s exclusive method of designing, maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater life The heater meets progressive requirements of the plastic processors

We are offering mica band heaters. Description: php's mica band heaters are designed and manufactured with more than 40 years of practical experience, for superior performance and life expectancy., as a manufacturer specialized in industrial electric heating elements & the desire to provide quality products and services to our customers both oem's & end users, php's specializes in designing mica band heaters, ceramic band heaters , nozzle heaters & strip heaters to your exact specifications. Depending upon applications php's mica band heaters are manufactured with high temperature oxidation metal sheath and high grade mica insulation resistant to moisture and high temperatures. A superior grade nicr resistance wire is evenly wound to provide uniform and reliable heat distribution with the best combination of physical strength, high emissivity & good thermal conductivity to heat cylindrical parts, good for sheath temperature up to 3000c. Php's mica band heaters are also available in various construction styles with special inbuilt energy saving options. features: 1. available in premium, economy & power saving options. 2. conserves energy with improved heating efficiency upto 30 watts per square inch. 3. designed for temperatures up to 300 deg. C. 4. special high grade mica insulation for superior thermal conductivity. 5. engineered for longer life with superior quality nichrome wire for uniform temperature & maximum amperage carrying capacity. 6. available in various lead terminations & clampings. 7. robust terminal junction with specially designed chrome nickel steel protection cap. 8. expandable to fit around the barrel o.d. Easy installation & removal. 9. available in brass, chrome nickel steel & ms galvanized sheathing. applications: 1. injection moulding machinery 2. blow moulding machinery 3. film & pipe extruders 4. laboratory equipment. 5. all plastic & rubber processing machinery. 4 construction styles: 1. Eco-heat construction ¢ ms inner sleeve & steel clamping ¢ screw post terminal with ceramic cap steel protection box. ¢ single piece construction ¢ clamping : barrel nut type ¢ also available in two piece construction 2. Premium-heat construction ¢ chrome nickel steel clamping with brass inner sleeve. ¢ 500 mm glass fibre insulated metal braided cable. ¢ terminal protection box, unless specified. ¢ single piece construction. ¢ clamping : barrel nut type ¢ also available in two piece construction 3. Power saver construction ¢ chrome nickel steel clamping with chrome nickel steel inner sleeve. ¢ energy saving insulted jacket (3 mm thick) ¢ barrel nut type clamping with terminal protection box, unless specified. ¢ 500 mm glass fibre insulated metal braided cable. ¢ single piece construction. ¢ also available in two piece construction. 4. Power saver plus construction ¢ chrome nickel steel clamping with brass chrome nickel steel inner sleeve. ¢ energy saving insulted jacket (16mm thick) ¢ barrel nut type clamping with terminal protection box, unless specified. ¢ 500 mm glass fibre insulated metal braided cable. ¢ single piece construction. ¢ also available in two piece construction. electrical variations: 110 - 440v 1. single phase: php's band heaters are usually designed on 230 volts single phase unless specified. 2. dual phase: mica band heaters can be designed with multiple circuits to operate in single or dual-phase circuits.

We present to our esteemed clientele, Mica Band Heaters. The Mica Band Heaters offered by us are equipped with a built in insulation, which is specially formulated for the excellent heat reflection and performance capabilities. In addition, flexible one or two-piece design makes installation faster & easier and its flexible construction allows the heater to be opened to the full diameter of the cylinder. The Mica Band Heaters meet progressive requirements of the plastic processors. Features Excellent thermal conductivityEfficient heat transfer capabilityMineral insulated for hot runner moldsExcellent controllabilityS.S. Enterprises Mica Band Heaters are widely used to heat the molds, dies, nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machineryThe mica Band heater is most economicIt provides excellent thermal conductivity as heat transfer by "conduction"Due to its best heat transfer capability, faster heating up a cooling down is possibleMineral insulated for hoi runner moldsMaximum watt density = 25 watts/ square inchesNote : In case where high watt densities are required, it is important that all heaters should be used with appropriate, approved and precise temperature control/ sensor device (a). The built in insulation is specially formulated for the excellent heat reflection a performance capabilitiesThe low mass heaters give the best controllability. The lower the thermal mass, lesser time required to deliver the heat to the object to be heated due to low mass and high conductivity, the Polymer Melt is heated quickly resulting autotune function on a control works bestFlexible one or two-piece design makes installation faster & easier its flexible construction also allows the heater to be opened to the full diameter of the cylinderThe most common square, rectangaular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or thermalsS.S Enterprises exclusive method of designing maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater lifeThe heater meets progressive requirements of the plastic processors

mica barrel heater, Energy Saving Band Heater, energy saving mica band heater

Mica Band Heaters are designed and manufactured with more than 40 years of practical experience, for superior performance and life expectancy., As a manufacturer specialized in industrial electric heating elements & the desire to provide quality products and services to our customers both OEM's & End Users, Vinman's specializes in designing Mica Band Heaters, Ceramic Band Heaters , Nozzle Heaters & Strip Heaters to your exact specifications. Depending upon applications Vinman's Mica Band Heaters are manufactured with high temperature oxidation metal sheath and high grade mica insulation resistant to moisture and high temperatures. A superior grade NiCr resistance wire is evenly wound to provide uniform and reliable heat distribution with the best combination of physical strength, high emissivity & good thermal conductivity to heat cylindrical parts, good for sheath temperature up to 3000C. Vinman's Mica Band Heaters are also available in various construction styles with special inbuilt Energy saving options. Features: 1. Available in Premium, Economy & Power Saving options. 2. Conserves Energy with improved Heating Efficiency Up to 30 Watts per square inch. 3. Designed for Temperatures up to 3000C. 4. Special High Grade Mica insulation for Superior Thermal Conductivity. 5. Engineered for Longer life with Superior quality Nichrome wire for uniform Temperature & Maximum Amperage carrying capacity. 6. Available in various Lead Terminations & Clampings. 7. Robust Terminal junction with Specially Designed Chrome Nickel Steel Protection Cap. 8. Expandable to fit around the Barrel O.D. Easy installation & removal. 9. Available in Brass, Chrome Nickel Steel & MS galvanized Sheathing. Applications: 1. Injection Moulding machinery 2. Blow Moulding machinery 3. Film & Pipe extruders 4. Laboratory Equipment. 5. All Plastic & Rubber Processing Machinery. 4 Construction Styles: 1. Eco-Heat Construction 2. Premium-Heat Construction 3. Power Saver Construction 4. Power Saver Plus Construction Electrical Variations: 110 - 440V 1. Single Phase: PHP's band heaters are usually designed on 230 Volts single phase unless specified. 2. Dual Phase: Mica Band Heaters can be designed with multiple circuits to operate in single or dual-phase circuits. Nominal Unheated Area One piece construction 1" x width Two piece construction 2" x width Holes and Cutout size x ½"x width.

Cabinet Dryer Tray Oven, Sulthises Crucible, Copper Melting Induction Furnace