Mica Heaters Dealers in Andheri, Mumbai

EXCEL’s Mica Band Heaters are widely used to heat the molds, dies,  nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machinery The mica heater is most economic It provides excellent thermal conductivity as heat transfer is by “conduction” Due to its best heat transfer capability, faster heating up & cooling down is possible Maximum sheath temperature upto 480°C (900°F) Maximum watt density = 25 watts/square inches Note: In case where high watt densities are require, it is important that All  heaters should be used with appropriate, approved and precise  temperature control/sensor device(s) The built in insulation is specially formulated for the excellent heat  reflection &performance capabilities The low mass heaters give the best controllability. The lower the thermal  mass, lesser time required to deliver the heat to the object to be heated.  Due to low mass and high conductivity, the“Polymer Melt” is heated  quickly. Resulting autotune function on a control works best. Flexible one or two – piece design makes installation faster & easier . Its  flexible construction also allows the heater to be opened to the full  diameter of the cylinder The most common square, rectangular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or terminals EXCEL’s exclusive method of designing, maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater life The heater meets progressive requirements of the plastic processors

Being a reliable Manufacturer, Exporter and Supplier, we offer high quality Mica Band Heater. Our Mica Band Heaters are primarily designed for normal heating performance at a working tern of 450°C. With these heaters, the level of performance is achieved from a mineral known as mica. Our Mica Band Heaters are designed with close ends so as to protect them against contamination. This also enables its installation without causing any internal damages. The outer sheath of these heaters is constructed in stainless steel and brass, with various terminal options. We can manufacture these heaters in different diameters, watts, and volts, as per your specification. Benefits Low temperature capabilityLong service lifeLow energy costHeat transfer not affected by surface and can be easily installed and removed Application Barrels and dies of InjectionBlow Molding MachineExtrudersAutoclaves & Chemical Reactors

We are a prominent manufacturer and suppler of an extensive range of Mica Heater that is widely used for various applications such as heating the nozzle of plastics processing, extrusion machine, rubber vulcanizing machine and injection molding machine. Our range of product is well acknowledged among the clients for its innovative designs, long service life and cost effectiveness.

PHP Mica Strip Heaters offered by us are high on demand in the market. The Mica Strip Heaters offered by us offers superior performance and higher life expectancy. These heaters are good for sheath temperature up to 250 C. The strip Heaters are available with various construction styles with various lead exit options. Also, clients can be benefited from the availability of Mica Strip Heaters at the competitive prices. Applications : Sealing EquipmentDie, Mould & other surface HeatingHot stamping, Hot PlatesFor use where surface contact on both side of heater if necessary Post Terminal Dimension And Location : Post Terminal are located 1/4" from edge of heated section either vertical , parallel or at opposite endsMounting holes may be located anywhere on the  heater as long as there is minimum of 1" between the edge of the hole and one side of the heater Options Available In Mica Strip Heater : S/S braided leads for flexibilityCustom mounting holesCeramic terminal coversSingle & Two Phase voltage Construction Mica Strip Heater - Fiberglass Leads :Fiberglass leads out same end center :10� lead standardLeads rated to 850oFLeads out same end edge :1/2" Sleeving at exitLeads out opposite end :1/2" Sleeving at exitLeads out at the top of heater :Brass eyelet where leads exit sheath1/2" Sleeving at exit

We present to our esteemed clientele, Mica Band Heaters. The Mica Band Heaters offered by us are equipped with a built in insulation, which is specially formulated for the excellent heat reflection and performance capabilities. In addition, flexible one or two-piece design makes installation faster & easier and its flexible construction allows the heater to be opened to the full diameter of the cylinder. The Mica Band Heaters meet progressive requirements of the plastic processors. Features Excellent thermal conductivityEfficient heat transfer capabilityMineral insulated for hot runner moldsExcellent controllabilityS.S. Enterprises Mica Band Heaters are widely used to heat the molds, dies, nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machineryThe mica Band heater is most economicIt provides excellent thermal conductivity as heat transfer by "conduction"Due to its best heat transfer capability, faster heating up a cooling down is possibleMineral insulated for hoi runner moldsMaximum watt density = 25 watts/ square inchesNote : In case where high watt densities are required, it is important that all heaters should be used with appropriate, approved and precise temperature control/ sensor device (a). The built in insulation is specially formulated for the excellent heat reflection a performance capabilitiesThe low mass heaters give the best controllability. The lower the thermal mass, lesser time required to deliver the heat to the object to be heated due to low mass and high conductivity, the Polymer Melt is heated quickly resulting autotune function on a control works bestFlexible one or two-piece design makes installation faster & easier its flexible construction also allows the heater to be opened to the full diameter of the cylinderThe most common square, rectangaular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or thermalsS.S Enterprises exclusive method of designing maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater lifeThe heater meets progressive requirements of the plastic processors

Mica Band Heater, Ceramic Band Heater, Mica Strip Heater, mica barrel heater

Mica Band Heater, Cabinet Dryer Tray Oven, Sulthises Crucible

Mica Strip Heater, capillary thermostats, energy regulator