Mica Heaters Dealers in Mumbai

• Phase: Single Phase
• Frequency: 50 Hz
• Voltage: 230 V
• Power: 1000 W
• Heater Material: Mild Steel
• Finishing Type: Polished
• Diameter: 7inch(Diameter)

• Type: Automatic
• Material: Mica
• Shape: Round
• Certification: CE Certified
• Color: Silver
• Voltage: 220V
• Power Source: Electric
• Phase: Single Phase
• Warranty: 1 Year

PHP Mica Strip Heaters offered by us are high on demand in the market. The Mica Strip Heaters offered by us offers superior performance and higher life expectancy. These heaters are good for sheath temperature up to 250 C. The strip Heaters are available with various construction styles with various lead exit options. Also, clients can be benefited from the availability of Mica Strip Heaters at the competitive prices. Applications : Sealing EquipmentDie, Mould & other surface HeatingHot stamping, Hot PlatesFor use where surface contact on both side of heater if necessary Post Terminal Dimension And Location : Post Terminal are located 1/4" from edge of heated section either vertical , parallel or at opposite endsMounting holes may be located anywhere on the  heater as long as there is minimum of 1" between the edge of the hole and one side of the heater Options Available In Mica Strip Heater : S/S braided leads for flexibilityCustom mounting holesCeramic terminal coversSingle & Two Phase voltage Construction Mica Strip Heater - Fiberglass Leads :Fiberglass leads out same end center :10� lead standardLeads rated to 850oFLeads out same end edge :1/2" Sleeving at exitLeads out opposite end :1/2" Sleeving at exitLeads out at the top of heater :Brass eyelet where leads exit sheath1/2" Sleeving at exit

APPLICATION Low cost electric heating of plastic processing, rubber vulcanizing, Drums, Barrels & cylinders etc. CONSTRUCTION Mica insulated Heaters consist of electric resistant ribbon / round wire element covered with zinc plated MS, Brass or SS sheet with clamps. Size & terminal connections as per requirement. CONNECTION For contact accessories, cable fittings, clamping devices, fixed & braided connection, heat resistant, flexible insulation with metal braided cable housing of any convenient length, connection boxes & types according to the band heatersdimensions, power & type of power supply.     STANDARD SIZES & CAPACITIES Max. Watt density: Any convenient Wattages up to 25 W/Sq. inch. Max. Surface Temp. 300 Deg. C. Supply (Volt) – Any convenient Voltage under the pre condition that it should be technically feasible

We are supply mica and ciramic normal and power shaving heater for injection , blow and extruder plastic machines.

Economy's Mica Band Heaters are designed for uniformly applying heat on cylindrical surface and are capable of being operated at elevated temperatures with along service life. These are shaped to suit many varying requirements such as inside diameter, width , wattage ,voltage etc.

Backed by highly knowledgeable professionals, we have been able to offer superior quality Mica Band Heater that are ideal for several industries for the heating purposes. Precisely engineered by our veteran professionals with the help of well tested raw material and modish technology, this heater is also checked on well-defined parameters to provide defect-free products to the clients. We provide this heater to our clients at nominal prices

• Power: 0.3 Kw

Mica bands are made of an electrical resistance ribbon or wire, which is wound around a mica winding card and sandwiched between two sheets of mica, then wrapped in sheet metal. The resistance wire or ribbon that converts electrical energy to thermal energy is normally a nickel-chromium alloy of either 80% nickel which is useful to 1100°C or 60% nickel which is useful to 950°c. The mica is, most often, one of three types: muscovite, useful to 500°c, phlogopyte, useful to 750°c, and synthetic mica, useful to 900°c. The sheet metal is normally either mild steel, stainless steel, brass, GI depending on the temp and the product to be heated. The maximum temp for mica band heater is 400°c. Features Designed as per customer specifications Variety of termination options Available in one or two piece construction Temp upto 400 deg C S.S. braided termination Metal covering Application Injection moulding Blow Moulding Extrusion Pipe and drum heating

Mica band heater, Standard Mica Band Heater:Die & Vessel Heating upto 200°C .Plug in Socket Arrangement. Cross Head Heaters: Special Cut, Extruder Special.

A practical method for applying heat to cylindrical forms Mica Insulated Band Heaters were manufactured in India by navbharat electrical industries in 1950's at a time when automatic machine moulding of plastic was introduced in India. They have since proven themselves as a dependable method of heat transfer for diverse industrial

We present to our esteemed clientele, Mica Band Heaters. The Mica Band Heaters offered by us are equipped with a built in insulation, which is specially formulated for the excellent heat reflection and performance capabilities. In addition, flexible one or two-piece design makes installation faster & easier and its flexible construction allows the heater to be opened to the full diameter of the cylinder. The Mica Band Heaters meet progressive requirements of the plastic processors. Features Excellent thermal conductivityEfficient heat transfer capabilityMineral insulated for hot runner moldsExcellent controllabilityS.S. Enterprises Mica Band Heaters are widely used to heat the molds, dies, nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machineryThe mica Band heater is most economicIt provides excellent thermal conductivity as heat transfer by "conduction"Due to its best heat transfer capability, faster heating up a cooling down is possibleMineral insulated for hoi runner moldsMaximum watt density = 25 watts/ square inchesNote : In case where high watt densities are required, it is important that all heaters should be used with appropriate, approved and precise temperature control/ sensor device (a). The built in insulation is specially formulated for the excellent heat reflection a performance capabilitiesThe low mass heaters give the best controllability. The lower the thermal mass, lesser time required to deliver the heat to the object to be heated due to low mass and high conductivity, the Polymer Melt is heated quickly resulting autotune function on a control works bestFlexible one or two-piece design makes installation faster & easier its flexible construction also allows the heater to be opened to the full diameter of the cylinderThe most common square, rectangaular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or thermalsS.S Enterprises exclusive method of designing maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater lifeThe heater meets progressive requirements of the plastic processors

Prayosha's Mica Band heaters are available with or without outer heat saving insulation covers. We make these heaters in S.S, Brass, MS, materials depending upon applications and requirement of actual users. Specially selected mica or micanite sheets and A specific gauge nickel-chrome resistance ribbon wire is used.

• Type: Band Heater
• Power Source: Electric
• Place of Origin: India
• Heaters: tempreture

"Sunil Heat" brand band heaters are made of nickel chrome resistance ribbon precisely wound on specially selected Mica or Micanite Sheet it is then insulated in metal sheating and rolled to the required diameter. Mica insulated band heaters are specially used to heat the cylinders on all types of plastic machinery. Band heaters can be made in two halves & customised thermocoulpe holes.     Uses: Plastic injection & Blow moulding machines extrusion barrels, cylenders, pipes drums etc. Band heater is a conveniently shaped element for both round & square surface easly installed with standard hardware.

We are a prominent manufacturer and suppler of an extensive range of Mica Heater that is widely used for various applications such as heating the nozzle of plastics processing, extrusion machine, rubber vulcanizing machine and injection molding machine. Our range of product is well acknowledged among the clients for its innovative designs, long service life and cost effectiveness.

We offer a wide variety of mica band heater. Mica Band Heater is manufactured as per customer’s specifications and details.These products are used in applications such as moulding, blow moulding, dies, rubber industry, plastic processing machinery and others.

Being a reliable Manufacturer, Exporter and Supplier, we offer high quality Mica Band Heater. Our Mica Band Heaters are primarily designed for normal heating performance at a working tern of 450°C. With these heaters, the level of performance is achieved from a mineral known as mica. Our Mica Band Heaters are designed with close ends so as to protect them against contamination. This also enables its installation without causing any internal damages. The outer sheath of these heaters is constructed in stainless steel and brass, with various terminal options. We can manufacture these heaters in different diameters, watts, and volts, as per your specification. Benefits Low temperature capabilityLong service lifeLow energy costHeat transfer not affected by surface and can be easily installed and removed Application Barrels and dies of InjectionBlow Molding MachineExtrudersAutoclaves & Chemical Reactors

EXCEL’s Mica Band Heaters are widely used to heat the molds, dies,  nozzles and especially to heat the cylinders (barrels) on all types of plastic(s) processing machinery The mica heater is most economic It provides excellent thermal conductivity as heat transfer is by “conduction” Due to its best heat transfer capability, faster heating up & cooling down is possible Maximum sheath temperature upto 480°C (900°F) Maximum watt density = 25 watts/square inches Note: In case where high watt densities are require, it is important that All  heaters should be used with appropriate, approved and precise  temperature control/sensor device(s) The built in insulation is specially formulated for the excellent heat  reflection &performance capabilities The low mass heaters give the best controllability. The lower the thermal  mass, lesser time required to deliver the heat to the object to be heated.  Due to low mass and high conductivity, the“Polymer Melt” is heated  quickly. Resulting autotune function on a control works best. Flexible one or two – piece design makes installation faster & easier . Its  flexible construction also allows the heater to be opened to the full  diameter of the cylinder The most common square, rectangular and hex-shaped mica heaters can be manufactured as per your specifications in one or two piece units. Available with leads or terminals EXCEL’s exclusive method of designing, maximizes the element wire coverage of the heated area. This results in uniform heat distribution & longer heater life The heater meets progressive requirements of the plastic processors

• Power Source: Electric
• Type: Band Heater
• Place of Origin: India
• Heaters: tempreture

Mica Heater, Mica Band Heaters, High Density Cartridge Heater