Om Steel Khetwadi, Mumbai, Maharashtra

We are a celebrated exporter and supplier of Titanium Tantalum Products based in Mumbai, Maharashtra. These products have a good thermal conductivity and resistance to corrosion. Tantalum is a shiny silvery metal with a soft texture when pure. Some of the uses of these products are in the manufacture of aircraft engines, electrical devices such as capacitors, surgical implants. We offer these products in the form of sheets, wires or rods.   Details : Tantalum Products is corrosion resistant and has good thermal conductivity. Some of its uses is heating elementsTantalum Wire is corrosion resistant and has good thermal conductivity. Some of its uses is in the suppling of heating elements, vacuum tubes and other high temperature parts. These are commonly used in various industrial applications due to its striking features.Tantalum is a shiny, silvery metal which is soft when is pure. It is almost immune to chemical attack at temperatures below 150 C. Tantalum is virtually resistant to corrosion due to an oxide film on its surface.   Uses : High-temperature applications, such as aircraft engines; electrical devices, such as capacitors; surgical implants and handling corrosive chemicals. It is rarely used as an alloying agent because it tends to make metals brittle. Tantalum resist corrosion and is almost impervious to chemical attack, for this reason it has been employed in chemical industry., vacuum tubes and other high temperature parts.   Tantalum Wire : Tantalum wire Tantalum- tungsten alloy wire Material: RO5200 RO5400 RO5252 (Ta-2.5W) RO5255 (Ta-10W) Available size: 0.3~4mm Standard: As per ASTM B 365-98. Purity: >=99.95 or 99.99   Tantalum Sheet : Tantalum Sheet is corrosion resistant and has good thermal conductivity. Some of its uses is in the manufacture of heating elements, vacuum tubes and other high temperature parts. All these sheets are fabricated as per client specific requirements.Tantalum sheet,Tantalum plate,Tantalum strip,   Tantalum Foil : Purity : 99.95min or 99.99min conformity with ASTM B 708 98 Size:  Thickness (mm) Width (mm) Length (mm) Foil 0.03-0.07 30-200>50 Sheet0.07-0.5 30- 700 30-2000 Board0.5-1050-1000 50-3000 Purity: >=99.95 or 99.99 Tantalum Rods : Material: RO5200 RO5400 RO5252 (Ta-2.5W) RO5255 (Ta-10W) Available size: 4~120mm Standard: As per ASTM B 365-98

We are a recognized exporter and supplier of Titanium Alloy based in Mumbai, Maharashtra. We offer different grades of this product in the form of seamless pipes, welded pipes, seamless tubes, welded tube, bar, wire, sheet, plate, forgings, pipe and fittings and flanges. These products that we offer are much in demand because of their excellent quality. Our prices of this product are the most reasonable in the market. Features : Titanium Grade 1-4 is pure Titanium, the other grades are alloys. Pure Titanium is used due to its high corrosion resistance, the alloys because of the extremely high strength to weight ratio. Grade 1. Pure Titanium, relatively low strength and high ductility. Grade 2. The pure titanium most used. The best combination of strength, ductility and weldability. Grade 3. High strength Titanium, used for Matrix-plates in shell and tube heat exchangers. Grade 5. The most manufactured titanium alloy. Exceedingly high strength. High heat resistance. Grade 7. Superior corrosion resistance in reducing and oxidizing environments. Grade 9. Very high strength and corrosion resistance.. Grade 12. Better heat resistance than pure Titanium. Applications as for Grade 7 and Grade 11. Grade 23. Titanium-6Aluminum-4Vanadium ELI (Extra Low Interstitial) Alloy for surgical implant Applications.   In what forms is Titanium Available at Om Steel ? Seamless Pipe Welded Pipe Seamless Tube Welded Tube Bar Wire Sheet Plate Forgings Pipe Fittings & Flanges   Details : Titanium Grade 1 : UNS R50250; ASTM Grade 1, CP titanium, C.P. titanium alloy Titanium Grade 2 : ASTM Grade 2; UNS R50400, CP titanium, C.P. titanium alloy Titanium Grade 3 : ASTM Grade 3; UNS R50550, CP titanium, C.P. titanium alloy Titanium Grade 4 : ASTM Grade 4: UNS R50700, CP titanium, C.P. titanium alloy Titanium Grade 7 : ASTM Grade 7; UNS R52400, CP titanium, C.P. titanium alloy Titanium Grade 9 : Ti3Al2.5V, UNS R56320; ASTM Grade 9; Half 6-4; Tubing Alloy TITANIUM Ti-5Al-2.5Sn : Titanium Ti-5Al-2.5Sn , UNS R54520; Ti-5-2.5 Titanium Ti-6Al-2Sn-4Zr-2Mo (Ti-6-2-4-2) : Ti6Al2Sn4Zr2Mo, Ti-6242; Ti-6-2-4-2; UNS R54620 Titanium Ti-6Al-4V (Grade 5) : Ti-6-4; UNS R56400; ASTM Grade 5 titanium; UNS R56401 (ELI); Ti6Al4V, bio materials, bio medical implants, bio compatibility Titanium Ti-6Al-6V-2Sn (Ti-6-6-2) Ti-662; Ti-6-6-2; UNS R5662

From Mumbai, Maharashtra we are a principal exporter and supplier of Stainless Steel Rods. The rods we offer are not only of excellent quality but also have a good finish which makes it a preferred product for use in the automobile industry. The nickel plating that we offer on these rods are long-lasting and does not flake, peel or wear off easily. Om Steel is a highly acclaimed manufacturer, exporter and supplier of Stainless Steel Round Bars in Various Grades.   Grades 201 202 303 304 304L 316 316L 310 410 420 430   Application : Stainless steel’s resistance to corrosion and staining, low maintenance and familiar lustremake it an ideal material for many applications. There are over 150 grades of stainless steel, of which fifteen are most commonly used. The alloy is milled into coils, sheets, plates, bars, wire, and tubing to be used in cookware, cutlery, household hardware, surgical instruments, major appliances, industrial equipment (for example, in sugar refineries) and as an automotive and aerospace structural alloy and construction material in large buildings. Storage tanks and tankers used to transport orange juice and other food are often made of stainless steel, because of its corrosion resistance. This also influences its use in commercial kitchens and food processing plants, as it can be steam-cleaned and sterilizedand does not need paint or other surface finishes. Stainless steel is used for jewelry and watches with 316L being the type commonly used for such applications. It can be re-finished by any jeweler and will not oxidize or turn black.Some firearms incorporate stainless steel components as an alternative to blued orparkerized steel. Some handgun models, such as the Smith & Wesson Model 60 and the Colt M1911 pistol, can be made entirely from stainless steel. This gives a high-luster finish similar in appearance to nickel plating. Unlike plating, the finish is not subject to flaking, peeling, wear-off from rubbing (as when repeatedly removed from a holster), or rust when scratched.Some automotive manufacturers use stainless steel as decorative highlights in their vehicles.

Surface Finishing : Polished

Application : Stay Wire

Length : 5Ft, 4ft

Thickness : 50-60mm, 40-50mm, 30-40mm, 20-30mm, 0-10mm

Country of Origin : India

The Stainless Steel Products that we offer have made us a prominent exporter and supplier based in Mumbai, Maharashtra. We offer these products in different forms, specifications and grades to ensure that we meet all customer requirement. The products we offer are guaranteed to be resistant to rust and corrosion as they are of superior quality and strength. Stainless Steel Angle, Channel, Flats, Circles, Rings : Grade 202, 304, 304H, 304L, 316, 316H, 316L, 316Ti, 309, 310, 317L, 321, 347, 904, 904L, 409, 409M, 410, 420, 430

The Stainless Steel Pipes that we offer have made us a primary exporter and supplier based in Mumbai, Maharashtra. These pipes are used in chemical and petrochemical processing, pulp and paper industries, desalination and wastewater projects and many more. We offer these pipes from different manufacturers such as Remi, Sumitomo (Japan), Prakash Steelage and Dongshin (Korea). Call us for information on the manufacturers we stock and for pricing details.   Stainless Steel SEAMLESS and ERW /Welded Pipes : We OM STEEL  are an ISO 9001:2008 Certified Company, take this profound pleasure to introduce ourselves as the major exporter, manufacturer & supplier of stainless steel SEAMLESS and ERW /welded pipes. Stainless Steel Pipes & Tubes : ASTM/ASME A/SA (312, 213, 269, 248) Grade 202, 304, 304H, 304L, 316, 316H, 316L, 316Ti, 309, 310, 317L, 321, 347, 904, 904L, 409, 409M, 410, 420, 430, Etc. Size Range: ERW (Welded) – ¼” NB to 80” NB. Typical applications for Stainless Steel Pipe Oil and gas Chemical and petrochemical processing LNG Pulp and paper Liquid natural gas piping Offshore construction Food and pharmaceutical processing Desalination and wastewater projects

We are a recognized supplier and exporter of Stainless Steel Fittings based in Mumbai, Maharashtra. We offer a broad spectrum of products which include forged socket weld, butt weld and threaded fittings to fit various outlets. These good quality fittings come in different sizes and specifications. Call us for further information and pricing details of these fittings. Timely delivery of orders is guaranteed. Range : Forged Fittings 15 NB to 100 NB in 2000 LBS, 3000 LBS, 6000 LBS and 9000 LBS available with NACE MR 01-75. Outlet’s ¼” to 24” in 3000 LBS, 6000 LBS, 9000 LBS available with NACE MR 01-75. Standard - ANSI/ASME, MSS, JIS, DIN, BS etc. Type - Socket Weld (S/W) & Screwed (SCRD) – NPT, BSP, BSPT Form - Elbow 45 Degree, 90 Degree & Three Way Elbow Tee – Equal, Reducing & Cross Union Full & Half Coupling Cap Nipple Bush Plug Hydraulic Fittings

We are a popular exporter and supplier of Nitronic Alloy based in Mumbai, Maharashtra. This alloy is a high strength and good corrosion resistant austenitic stainless steel. This alloy is able to maintain its strength even under the most extreme temperatures and is much preferred for use in pharmaceuticals, food and chemical industries. We stock this alloy in different forms, grades and specifications as might be required by the customer. Details : Nitronic 50 is a high strength and good corrosion resistant austenitic stainless steel. It has nearly double the yield strength of 304 and 316 stainless steel and has better corrosion resistance than 317L stainless steel. N50 Stainless remains non-magnetic even after being severely cold worked. It maintains strength at high temperatures as well as sub-zero temperatures Nitronic 60 is known for its excellent galling resistance, even at elevated temperatures. The additions of 4% silicon and 8% manganese inhibit wear, galling, and fretting. It is commonly used for various fasteners and pins that require strength and resistance to galling. It maintains decent strength up to temperatures of 1800oF and has oxidation resistance similar to that of 309 stainless steel. The general corrosion resistance is between that of 304 and 316 stainless steelAlloy 20, also known as Carpenter 20, is a nickel-iron-chromium austenitic alloy that was developed for maximum resistance to acid attack, specifically sulfuric acid. This superalloy has excellent resistance to general corrosion, pitting, and crevice corrosion in chemicals containing chlorides and sulfuric, phosphoric, and nitric acids. It also contains niobium for stabilization against sensitization and resultant intergranular corrosion. Carpenter 20 combines excellent corrosion resistance with elevated mechanical properties and relatively easy fabrication. Although originally designed for use in sulfuric acid related industries, Alloy 20 is now a popular choice for a wide variety of industries including the chemical, food, pharmaceutical, and plastics industries. In addition, this superalloy is used in heat exchangers, mixing tanks, metal cleaning and pickling equipment, and piping. There has long been a debate on whether Carpenter 20 is a stainless steel or a nickel alloy because the nickel content is right on the border of defining it as one way or the other. So, depending on who you talk to this alloy may be referred to as alloy 20 Stainless Steel or as a nickel alloy. Either way it is still great for corrosion resistance. In what forms Nitronic material is available at om steel.? Sheet Plate Bar Pipe & Tube (welded & seamless) Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples) Wire Grades And Specifications. AMS 5764,ASTM A 193, ASTM A 262, ASTM A 276, ASTM A 276 Condition A, ASTM A 276,Condition S, ASTM A 479,EN 1.3964,ISO 15156-3,NACE MR0175,UNS S20910,Werkstoff 1.3964

We are a foremost exporter and supplier of Nimonic Alloy based in Mumbai, Maharashtra. This nickel-chromium alloy has good mechanical properties and a good oxidation resistance at even high temperatures. Also known as Alloy 75 this product is commonly used in sheet metal fabrication. Other uses include in the manufacture of gas turbine engines, components of industrial furnaces and for heating treating of equipment. Details : Nimonic Alloy 75 (UNS N06075) is a nickel-chromium alloy with good mechanical properties and oxidation resistance at high temperatures. Alloy 75 is most commonly used for sheet metal fabrications which require oxidation and scaling resistance together with medium strength at high operating temperatures.  Alloy 75 is also used in gas turbine engines, for components of industrial furnaces, for heat treating equipment and fixtures, and in nuclear engineering.Alloy 80A is a nickel-chromium alloy similar to alloy 75 but made precipitation hardenable by additions of aluminium and titanium. Alloy 80A has good corrosion and oxidation resistance and high tensile and creep-rupture properties at temperatures to 815ºC (1500ºF). Alloy 80a is used for gas-turbine components (blades, rings, discs), bolts, tube supports in nuclear generators, exhaust valves in internal combustion engines and has many other offshore/marine, automotive and electrical applications. Alloys 254 / 254 SMO / 6 Mo is an austenitic stainless steel with a high molybdenum content. Coupled with Nickel and Copper this gives the alloy a good resistance to pitting and crevice corrosion, especially in environments containing halide ions, e.g. chloride, bromide and fluoride solutions.254 SMO (UNS S31254) may offer a cost effective solution to Nickel and Titanium alloys in these environments. Availability Round Bar Flat Bar Rod Tube Plate Sheet Strip Forging Stock and Wire

We are a vital exporter and supplier of Nickel Pipes based in Mumbai, Maharashtra. We offer two variations of this product Nickel 200 and Nickel 201. These pipes offered in various forms such as sheets, plates or bars have a good thermal, electrical and magnetic properties. They are highly resistant to caustic alkaline and are used in industries that deal with caustic soda.   Details : Nickel 200 and Nickel 201 are solid solution strengthened, commercially pure wrought materials with good mechanical properties over a wide range of temperatures and excellent resistance to many corrosives, in particular hydroxides. Nickel 201 was a modification of 200 to control carbon (.02 max) which keeps it from being embrittled by intergranular precipitates at temperatures of 600° F to 1400° F in many processes. Typically, the elemental restrictions of both, nickel 200 and nickel 201, are combined into one, dual-certified chemistry resulting in a single alloy with the desired characteristics of both alloys, Nickel 200/201. In what forms is Nickel 200/201 available at Om Steel.? Sheet Plate Bar Pipe & Tube (welded & seamless) Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples)   What are the characteristics of Nickel 200/201? Highly resistant to various reducing chemicals Excellent resistance to caustic alkalies High electrical conductivity Excellent corrosion resistance to distilled and natural waters Resistance to neutral and alkaline salt solution Excellent resistance to dry fluorine Widely used to handle caustic soda Good thermal, electrical and magnetostrictive properties Offers some resistance to hydrochloric and sulfuric acids at modest temperatures and concentrations

We are an essential exporter and supplier of Monel 400 based in Mumbai, Maharashtra. The Monel 400 that we offer has a good resistance to stress corrosion and to neutral and alkaline salts. These sheets are widely used in marine engineering, in gasoline and freshwater tanks, crude petroleum stills and in industrial heat exchangers. This product has good mechanical properties even in extreme temperatures.   Details : Monel 400 is a nickel-copper alloy (about 67% Ni – 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions. This nickel alloy is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated. As would be expected from its high copper content, alloy 400 is rapidly attacked by nitric acid and ammonia systems. Monel 400 has great mechanical properties at subzero temperatures, can be used in temperatures up to 1000° F, and its melting point is 2370-2460° F. However, alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.   In what forms is Monel 400 Available at Om Steel? Sheet Plate Bar Pipe & Tube (welded & seamless) Fittings (i.e. flanges, slip-ons, blinds, weld-necks, lapjoints, long welding necks, socket welds, elbows, tees, stub-ends, returns, caps, crosses, reducers, and pipe nipples) Wire   Characteristics Resistant to seawater and steam at high temperatures Excellent resistance to rapidly flowing brackish water or seawater Excellent resistance to stress corrosion cracking in most freshwaters Particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated Offers some resistance to hydrochloric and sulfuric acids at modest temperatures and concentrations, but is seldom the material of choice for these acids Excellent resistance to neutral and alkaline salt Resistance to chloride induced stress corrosion cracking Good mechanical properties from sub-zero temperatures up to 1020° F High resistance to alkalis   Corrosion Resistant Monel 400 Alloy 400 is virtually immune to chloride ion stress corrosion cracking in typical environments. Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions. It is not useful in oxidizing acids, such as nitric acid and nitrous. Nevertheless, it is resistant to most alkalis, salts, waters, food products, organic substances and atmospheric conditions at normal and elevated temperatures. This nickel alloy is attacked in sulfur-bearing gases above approximately 700° F and molten sulfur attacks the alloy at temperatures over approximately 500° F. Monel 400 offers about the same corrosion resistance as nickel but with higher maximum working pressures and temperatures and at a lower cost due to its superior ability to be machined.   Applications Marine engineering Chemical and hydrocarbon processing equipment Gasoline and freshwater tanks Crude petroleum stills De-aerating heaters Boiler feed water heaters and other heat exchangers Valves, pumps, shafts, fittings, and fasteners Industrial heat exchangers Chlorinated solvents Crude oil distillation towers

We are a well-recognized exporter and supplier of Hastelloy Products based in Mumbai, Maharashtra. The products we offer are able to withstand high temperature, stress, corrosion and adverse environment. They are used in nuclear and chemical reactors and in the manufacture of pipes and valves in the chemical industry. Made from high-grade nickel, we offer the Hastelloy C276 and Hastelloy B2.   Details : We Om Steel are one of the reliable Hastelloy B Exporters from India. Since our pure Hastelloy C22 is capable of withstanding high temperature, stress, severe corrosion and erosion prone environment, they find extensive usage in nuclear and chemical reactors, pipes and valves in diverse chemical industries. The predominant ingredient used in our Hastlealloy is high grade metal Nickel. The other grades that we offer our clients are Hastelloy C276 and Hastelloy B2.Within corrosion applications Hastelloy alloys are often chosen due to their relatively attractive price/performance ratio. In many corrosion media only Tantaline shows a dramatically better cost/performance ratio than Hastelloy.The predominant Hastelloy alloying ingredient is metal nickel. Other alloying ingredients are added to Hastelloy  includin varying percentages of the elements molybdenum, chromium, cobalt, iron, copper, manganese, titanium, zirconium,aluminum, carbon, and tungsten. The primary function of the Hastelloy alloys is that of effective survival under high-temperature, high-stress service in a moderately to severely corrosive, and/or erosion prone environment. Hastelloy alloys are used for many applications including pressure vessels, nuclear reactors, chemical reactors, as pipes and valves in chemical industry. Hastelloy C-276 Hastelloy C-276 alloy is a nickel-molybdenum-chromium wrought alloy that is generally used as corrosion-resistance. Hastelloy c-276(Hastelloy C276) is among the more well known Hastelloy grades for general corrosion service. Hastelloy C-276 alloy is an improved wrought version of Hastelloy alloy C. Hastelloy C-276 key words ASME SB-574, SB-575, SB-619, SB-622, SB-626, Boiler Code Sections I, III, VIII, IX; Werkstoff Nr. 2.4819, Nickel-Chromium Alloy; UNS N10276; ASTM B 574, B 575, B 619, B 622, B 626, B 751; NACE MR-01-75; DIN 17744, 17750-17752, INCONEL Alloy C-276, Nickelvac HC-276,, Nicrofer 5716 Hastelloy C-4 Hastelloy C-4 alloy is a nickel-chromium-molybdenum Hastelloy alloy with good high-temperature stability. The Hastelloy C-4 is an Hastelloy grade, that resists the formation of grain-boundary precipitates in weld heat-affected zones.  Hastelloy C-4 alloy also has excellent resistance to stress-corrosion cracking and to oxidizing atmospheres. Hastelloy C-4 is also used in a varity of chemical process environments. Hastelloy alloy C-4 Key Words - ASME SB-622, ASME SB-626, UNS N06455, ASME SB-574, ASME SB-575, ASME SB-619, Hastelloy alloy C-22 ASME SB-622, ASME SB-626 ASTM B-574, ASTM B-575, ASTM B-619, ASTM B-622, ASTM B-626, DIN 17744 No. 2.4602, TUV Werstoffblatt 479, UNS N06022, ASME SB-574, ASME SB-575, ASME SB-619, NACE MR-01-75, Inconel 22, Nicrofer 5621 Hastelloy G Hastelloy G is an nickel-chromium-iron-molybdenum alloy developed for corrosion resistance in both oxidizing and reduceing media. Hastelloy G shows good resistance to sulfuric and phosphoric acid. Hastelloy G may further handle both acid and alkaline solutions. Hastelloy X Hastelloy X alloy - a nickel-chromium-iron-molybdenum alloy - has been developed to combine oxidation resistance, fabricability and high-temperature strength.  Hastelloy X is also It has also been found to be resistant in petrochemical applications Hastelloy X Key Words ASME SB-435, SB-572, SB-619, SB-622, SB-626, Boiler Code Sections III, VIII, IX, Nickel-Chromium Alloy; Werkstoff Nr. 2.4665, SAE AMS 5536, 5587, 5588, 5754, 5798, 7237; WL Nr. 2.4665; AFNOR NC 22 Fe D; NACE MR-01-75; AECMA Pr EN 2182 - 2185, UNS N06002; BS HR6, HR204; ASTM B 435, B 572, B 619, B 622, B 626, B 751, Nickelvac HX, Nicrofer 4722, Altemp HX, Inconel HX Hastelloy B-3 Hastelloy B-3 alloy is a member of the nickel-molybdenum family of Hastelloy alloys. Hastelloy B-3 is the alloy in the Hastelloy family that shows best resistance to hydrochloric acid. Hastelloy B UNS N10001, ASTM B494, ASTM B333, ASTM B335, ASTM B366, ASTM B619, Nimofer6928 HastelloyB-2 UNS N10665, ASTM B333, ASTM B335, ASTM B366, ASTM B619, ASTM B622, ASTM B626 In what applications is Hastelloy used? Pharmaceutical industries use hastealloy fittings and tubing to avoid contamination caused by corrosion related failures Cellophane manufacturing Chlorination systems Pesticide production Incineration scrubber systems Chemical process industry in equipment like flue gas scrubbers, chlorination systems, sulfur dioxide scrubbers, pulp and paper bleach plants, pickling systems, and nuclear fuel reprocessing Waste water processing Gas turbines Petrochemical industry Industrial furnaces Heat treating equipment Nuclear engineering Jet engine combustion chambers Aircraft cabin heaters Turbine exhaust components

We are an eminent exporter and supplier of Flanges based in Mumbai, Maharashtra. We offer flanges made from stainless steel, carbon steel, alloy steel, aluminium, nickel alloy and much more to meet all customer requirements. The flanges are guaranteed to be durable and can withstand extreme conditions. The flanges are not only of good quality but also offer a superior performance. Range : ½” (15 NB) to 60” (1500NB) in 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS, ASA 150, ASA 300, PN 6, 10, 16, 25, 40, 64, 100, 160 Etc Form : Slip On / SORF Flanges Weld Neck / WNRF Flanges Socket Weld / SWRF Flanges Blind / BLRF Flanges Lap Joint Flanges Threaded Flanges Long Weld Neck Flanges Spectacle Flanges Ring Joint Flanges Orifice Flanges Customized Flanges

We are a famous exporter and supplier of Duplex Stainless Steels based in Mumbai, Maharashtra. These steels have a high strength and a greater resistance to corrosion particularly stress corrosion and cracking. We offer this product in different qualities or grades. These steels are used in various processing plants, hot water tanks and much more. Our wholesale prices on this product are unbeatable. Details :Duplex stainless steels are becoming more common. They are being offered by all the major stainless steel mills for a number of reasons Higher strength leading to weight saving Greater corrosion resistance particularly stress corrosion cracking Better price stability Lower price There is a conference on the subject of duplex every 2-3 years where dozens of highly technical papers are presented. There is a lot of marketing activity surrounding these grades. New grades are being announced frequently. Yet, even with all this interest, the best estimates for global market share for duplex are between 1 and 3%.The purpose of this article is to provide a straightforward guide to this steel type.   Grades : Duplex Grades Duplex 31803 Super duplex s32750 Super duplex s32760 Lean duplex s32304 6 molu s31254 Zeron 100.   Principle of Duplex Stainless Steels : The idea of duplex stainless steels dates back to the 1920s with the first cast being made at Avesta in Sweden in 1930. However, it is only in the last 30 years that duplex steels have begun to “take off” in a significant way. This is mainly due to advances in steelmaking techniques particularly with respect to control of nitrogen content. The standard austenitic steels like 304 (1.4301) and ferritic steels like 430 are relatively easy to make and to fabricate. As their names imply, they consist mainly of one phase, austenite or ferrite. Although these types are fine for a wide range of application.   Technical Weaknesses Austenitic – low strength (200 MPa 0.2% PS in solution annealed condition), low resistance to stress corrosion cracking Ferritic – low strength (a bit higher than austenitic, 250 MPa 0.2% PS), poor weldability in thick sections, poor low temperature toughness In addition, the high nickel content of the austenitic types leads to price volatility which is unwelcome to many end users. The basic idea of duplex is to produce a chemical composition that leads to an approximately equal mixture of ferrite and austenite. This balance of phases provides the following: Higher strength – The range of 0.2% PS for the current duplex grades is from 400 – 550 MPa. This can lead to reduced section thicknesses and therefore to reduced weight. This advantage is particularly significant for applications such as Pressure Vessels and Storage Tanks Structural Applications e.g. bridges Good weldability in thick sections – Not as straightforward as austenitics but much better than ferritics. Good toughness – Much better than ferritics particularly at low temperature, typically down to minus 50 deg C, stretching to minus 80 deg C. Resistance to stress corrosion cracking – Standard austenitic steels are particularly prone to this type of corrosion. The kind of applications where this advantage is important include Hot water tanks Brewing tanks Process plant Swimming pool structures Characteristics Twice design strength of austenitic and ferritic stainless steels Wide range of corrosion resistance to match application Good toughness down to minus 80 deg C but not genuine cryogenic applications Particular resistance to stress corrosion cracking Weldable with care in thick sections More difficult to form and machine than austenitics Restricted to 300 deg C maximum .

We are the main supplier of this product.

Material : Copper

Thickness : 0.18mm-0.25mm

Length : 1-1000mm

Color : Copper

Finishing : Polished

Technique : Hot Rolled

We are a top exporter and supplier of Brass Products based in Mumbai, Maharashtra. The products we offer are brass tubes, foil, ferrule fittings, rings, plates and more which are suited to meet all customer requirements of this product. This alloy which is made up of zinc and copper has a bright appearance like gold and is used in low friction applications such as locks or gears.

We are listed amongst the best exporters and suppliers of Bi Metal Products based in Mumbai, Maharashtra. We offer sheets, strips, washers and plates of this product which are used to make printed circuit boards, cable lugs and cable end connectors and more. The Bi-metal offered consists of aluminium and copper sheets mechanically welded together to form a whole unit via a rolling bonding process. List of Bimetal Products Bimetal Sheet Bimetal  Strips Bimetal  Washers Bimetal Plates Bimetallic  Washers Bimetallic  Plates Applications : Substation and Switch-yard Bimetallic Clamps and Connectors Cable Lugs and Cable end Connectors Distribution ,panel boards ,bus ducts and bus bar chambers isolators and switch gears safety vent for Li-Ion secondary battery semiconductor packages Printed Circuit Boards(PCB) CPU heat Sink IC heat Sink Electronic and Electronic Components other Electrical application

We are listed amongst the distinguished exporters and suppliers of Aluminium Products based in Mumbai, Maharashtra. We offer different varieties of aluminium such as aluminium pipe, square pipe, rectangle pipe, sheets, plates, chequered plates, round bars, square bars, flat, angle, foil and circle. These products are much in demand for use in different applications in various industries such as food and chemical industries. We are known for are good quality products and timely delivery of orders.

We are a leading exporter and supplier of Aerospace Products based in Mumbai, Maharashtra. The excellent quality of our products makes them widely used in various fields such as defence, nuclear, petrochemicals and medicals. We offer a wide range of aerospace metals that have a high mechanical strength. We ensure that these aerospace products are manufactured in keeping with industrial norms and standards.   Features : Alloy A286 - UNS S66286 (UNS K66286), AMS 5525, AMS 5731, AMS 5732, AMS 5734, AMS 5735, AMS 5736, AMS 5737, AMS 5804, AMS 5805, ASME SA638, ASTM A453 GR.660, ASTM A638, SAE J467 (A286); DIN 1.4980/1.4944, Altemp® A286, Pyromet® Alloy A-286 17-4PH Stainless Steel ASTM A693 grade 630 (AMS 5604B), UNS S17400  EURONORM 1.4542 X5CrNiCuNb 16-4  AFNOR Z5 CNU 17-4PH  DIN 1.4542  A 17Cr-4Ni-3Cu 15-5PH Stainless Steel -15-5 PH, 15-5PH, 15/5 PH, 15/5PH, XM12, AMS 5862, ASME SA705 (XM-12), ASTM A564 (XM-12), ASTM A693 (XM-12), ASTM A705 (XM-12), AFNOR NF A35-581 Z6CNU15.05, DIN 1.4540, DIN X4CrNiCuNb164, Cr-Ni 15-5, UNS S15500, AMS 5658, AMS 5659, AMS 5826 PH 13-8 Mo Stainless Steel - UNS S13800, 13-8Mo, 13-8PH, 13-8 PH, 13/8 Mo, 13/8Mo, 13/8PH, 13/8 PH, AMS 5629, AMS 5840, ASME SA705 (XM-13), ASTM A564 (XM-13), ASTM A693 (XM-13), ASTM A705 (XM-13); PH 13-8 Mo; Precipitation Hardening, DIN 1.4534 , X3CrNiMoAl 13 8 2 , Nitronic® 50 - Bar ASTM A276 ASTM A479, AMS 5764; Plate/Sheet ASTM A240, ASTM A412, AMS 5861, Pipe & Tube SPECIALS, ASTM A312, ASTM A403, UNS S20910; Forgings ASTM A314; Fasteners ASTM A193/ASTMA194; Welding Wire AWS ER209; NACE MR-01-75 Nitronic® 60 - Fasteners A193/A194; Welding Wire AWS ER218, UNS S21800; Bar ASTM A276 ASTM A479, AMS 5848; Plate/Sheet ASTM A240; Forgings ASTM A314