WITHDRAW PULL TEST APPARATUS
As per IS 1293 - 1988 clause - 21. The socket outlet are mounted in normal used & the pulling force is applied in the direction similar to the normal used. The socket outlet is held in a vertical plane & the pulling on the projecting part of it downmost . The applicable force should be applied as per table given below to have necessary withdraw the plug from the socket outlet.
...moreWATER SUSPAN ORTHOPAEDIC MOULD
Water Suspan is Exclusively used for heating Hospital based Thermoplastic sheets to prepare mould for occupational therapy & splint application used in physical rehabilitation. It has been made with the state of art technology & meets the high standard with intelligent & user-friendly operation. It has a special feature like constant temperature bath with water starring arrangement, where water medium is heated with immersion heater .For quick heating additional optional Booster heater is provided. The control of water temperature is through a microprocessor based digital temperature controller cum timer with safety thermostat & Pt 100 sensor. A unique water level controller is incorporated with bath to save Dry run of Heater. The Heaters will be automatically cut-off, when sufficient water is unavailable followed by Buzzer scrambling. An imported & sturdy drain cock is fitted for ease draining.
...moreWater Distillation Unit
The unit is used for producing pyrogen free distilled water in R&D labs, biological labs, hospitals and clinical research laboratories. The unit is wall - mounting with the full Body made up of stainless steel fitted with ISI certified safety ejection type immersion heaters. A constant water level arrangement is provided. A steam baffle is provided to take steam direct to the cold - water jacketed condenser. The stated output of the still is approximate as it is bound to vary according to the voltage of the MAINS. An electronic watch dog water level system with auto heater cut-off when water level is low along with buzzer can be provided at extra cost.
...moreVISCOSITY SAY BOLT FUROL APPARATUS
Unit consists of oil tube (as per specified required dimensions and made of corrosion resistant metal) , water bath and stirring apparatus and digital temp. Controller cum indicator, with PT100 sensor for accurate measurement of temperature, timing device (digital timer circuit), and graduated glass receiver.
...moreViscosity Bath
The Viscosity Bath is designed to simplify ASTM D 445; IS-1206 (Part III)-1978 kinematic viscosity testing. A top-mounted controller keypad permits quick entry of bath set point temperature while a sophisticated microprocessor controls the bath heating and stirring. To further enhance the input, the unit accommodates up to a maximum of six individual capillaries. The HVB features a measuring range of 5ºC to 230ºC and can be used with mineral oil, silicone oil, or water as the bath media. Bath temperature is displayed on a bright, easy-to-read digital display. In addition, the unit features a built-in over-temperature circuit and bath liquid level detector to automatically cut heater power in the event of thermal runaway or insufficient bath media.
...moreVertical Autoclave
The unit has a double walled construction, complete with fully SS 304 construction (Argon Welded Chamber) & a Jacket of 18 SWG. The unit is fitted with an efficient radial locking system made of mild steel, chrome plated, with paddle lifting device. The unit is supplied complete with stainless steel basket. The unit is fitted with safety and pressure release valves, water level indicator, cord & plug. The machine is fitted with a fully automatic microprocessor based temperature controller. The cycle is fully automatic including purging, sterilizing, rapid cooling & safety features such as process timer, low level water alarm, over heat Protection, high-pressure cutoff, two mechanical safety valves etc. The lid is made of SS.304, with Silicon rubber gasket used for sealing, supplied with pressure gauge & unique special round heater - to achieve pressure up to 20 Psi.
...moreTORSION TEST APPARATUS
This test is basically used for plugs & socket outlets. For this purpose sample being drawn preferably at random from the regular production lot. The plug is fitted with the flexible cord or cable, the conductors are introduced into the terminals & the terminals are tightened by applying 23rd of the torque specified in the said IS table - 4 ,so that the conductor may not easily change the position . Immediately after the cord - grip test as specified in clause 22.1 & 22.2 the cord is subjected for a period of one minute to a torque of 1.5 Nm. During the test no damaged shall be caused to the flexible cord.
...moreCleveland Open Cup Flash Point Tester
This flash point and fire-point test method is a dynamic method and depends on definite rates of temperature increases to control the precision of the method. Its primary use is for viscous materials having a flash point between 79 deg C (175 deg F) and 400 deg C (752 deg F) except fuel oils, to define the hazards of flammable and combustible materials used in shipping and safety regulations. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions.
...moreSOXHLER EXTRACTION UNIT
GMP model GC-78 offers an innovative feature in rapid oil extraction unit for textile industries. The unique feature are oil contents of tops & similar materials of clothes can be detected in less than 15 MIN, ideal for process control in the Textile mills. Simple, compact robust construction & fully made of SS 316. The apparatus was developed specifically for obtaining the oil content of Tops & similar cloth material. The principal of extraction is percolation of solvent through the wool sample in a simple metal tube. The extract as it drips from the tube is collected on a light aluminum tray held between two metal ring mounted on a temperature controller hot plate. The company provides the SS 316 ring mesh tray instead of Aluminum Tray .The method is applicable to tops, card slivers, Yarns & similar material from which small samples can be taken with confidence. These models are available jointly as one, two three extraction unit.
...moreTARPAULINE - LOUVANDRO METER
The unique apparatus is used for determination of colour fastness of all textile materials irrespective of there composition & their form (yaru fibre etc.) to the action of soap & sodium carbonate solution at 60 degree C .The principle of this is that a specimen of textile in contact with the pieces of specified adjacent fabric is mechanically agitated in a soap soda solution rinsed & dried & the hang in colour of the specimen & the stirring adjacent fabrics are assessed with standard grey scales. The apparatus consist of a Argon weld Stainless Steel water bath containing a rotor with which glass container flask of 500ml.capacity are rotated at a speed of 40+_2 revmin &thermostatically controlled electrical heating device to heat the water bath so as to maintain the temperature of test solution in container at 60+_2 degree C.A mechanical timer of 30 minutes is fitted for time duration of test .A soap soda solution is to be poured in flask after the temp maintain to 60 degree C The given specimen is dropped in glass flask & rotoris rotated at a 40rpm fixed for 30mints.The results are to be obtained & tested as per specification. Digital temperature controller can be given as option.
...moreTest Apparatus
TC MC basically used for checking Damage to Conductor. The apparatus consists of thick Acrylic Sheet table top compact body with locking door. The test specimen is fitted at top of unit with provision for height adjustment as per new amendment &Circulation. Double ball bearing shaft coupled with constant speed of 10rpm-geared motor to rotate the circular acrylic disk. The geared motor is Electrically coupled with the timer of 15mints. As per demand of the IS specified test. The different weights in cylindrical shape & bushes as per IS specification is given with the unit. Our GMP model unit can accommodate 6A 16A 32A switches.
...moreSTYRO FOAM CUTTER FOR ONCOLOGY
The accurate, easier, fast &profession's choice for cutting Therapeutic shielding forms like writing with fine pen. The styroformer offers the best cost benefit ratio of any available block cutter in the market. Styroformer machine includes verification light, three tracing tips & self locating block holding arms. Basic machine plus hot wire temperature booster & alarm system. The accessories of the cancer treatment radiation process are cold plate, Alloy melter, U.V. source, lead shield trolley. The unique apparatus is basically designed & developed for exposing only those specific area of human body for giving chemotherapy of the human body there by un affected portion is shielded from the hazardous chemotherapic radiation. Thus it is more precise & perfect .The mc is user friendly & very easy to operate. The unique styroform cutter is indigenously made & constant improvement in its end use makes it more suitable & economical for treatment of cancer effected area. It basically works on the principle of penetrograph mc where after initial alignment of the mc the x-ray film of the affected area is kept on a well fluorescent illuminated table. A pointer with a hot 75 mm Nicrom wire is used for cutting, after cutting the cut area can be verified easily for area radiation by verification light of high powered reflected halogen lamp. Where the shadow of the cutting edge matches with that of edge of x-ray film already marked. Various accessories along with Styrofoam cutter like u.v source for illumination of cancerous body for focusing x-ray camera & fluorescent marker pen for marking human body cancerous cell helps in locating defined areas. Low melter alloy consists of perfect % of tin lead bismuth mn mg etc: cooling plate with silicon matt etc. provides adequate support along with Styrofoam cutter for better treatment of cancer, in oncology department.
...moresalt spray corrosion cabinet
The Global Corporation Salt spray Corrosion Cabinet is used to test the corrosion resistance of protective lacquer coating on ferrous &non ferrous material. Made of perfect inert material (Acrylic) Suitable for panels of size 150mm x 100mm x 1.25mm The panel will be placed at an angle of 15° on Acrylic The panels are equally placed at a distance of 20mm from each other as well from the walls.
...moreWater Bath
The bath has been designed with highly advance & Revolutionary cooling system to operate wide range from 1 c to 95 c to meet various needs. Double walled, Tough finished, Stainless Steel Chamber, Top & Exterior of G.I M.S finished in epoxy powder coated finish. Hermetically sealed compressor -fan motor-condenser having Environment friendly gas for below ambient temperature, does the process & for above ambient SS immersion heater is used. The heat is transmitted from generator to water by direct conduction. A Motorized stirrer is mounted for uniformity of temp. of the bath. Digital temperature controller cum indicator controls the process.
...moreROTARY SHAKING ELECTRICAL DRYING OVEN
Construction :- Industrial Tray Drier having cross-directional horizontal air-flow system by flange mounted motorized fan for rapid drying of material kept inside. Inner chamber made of MS and coated with heat resistive silver paint or SS-304 (20G). Temp Range :- Ambient to 250ºC. Controls :- Unit is controlled by microprocessor based auto-tune PID controller with PT-100 sensor located at the top of oven. Safety thermostat in series with digital temperature controller given as a fail - safe. Heater :- Heater is of SS, finned, hot + cold zone type star connection mode for 3ϕ and terminal taken out of oven from the sides with proper cover for easy accessibility. Air vent provided at the top of oven.
...moreRing & Ball Softening Point Apparatus
Unit consists of steel balls and brass rings as per IS specified dimensions, ball guide for ball centering, support for the ring, all mounted in a beaker which is provided with magnetic stirrer and a Immersion heater to heat the liquid inside. Temperature is maintained with the help of a programmable digital temp. Controller provided with PT100 sensor to achieve 5 degree Cmin. temperature rise.
...moreRectangular Hot Plate
The heating plates are rectangular in shape and made up of MS Cast Iron plates with Groves for Heating Coil (SS Plate can also be provided on request) .The top plates overhang by supporting MS pillar which allows air insulation between plate and control Compartment to keep it cool. Long lasting Nicrome Heating wire with ceramic Beads are used for the heating process. A choice of Energy Regulator Digital Temperature controller is provided.
...morePortable Autoclave
GMP - GC - 29 portable autoclave is a reliable and convenient method for steam and sterilization of medical equipments. The unit is a single walled SS - 304 (heavy gauge) structure with high gloss finish with argon welded finish. The lid is heavily polished and fitted with a pressure gauge, steam exhaust valve, safety valve and handle and can withstand a pressure of 15 Lbs Sq. inch. The unit is also equipped with an ISI marked special heater which is easily replaceable, & SS basket.
...moreTRANSFER DISH PENETROMETER
Bath Unit consists of container of specified dimensions, needle, transfer dish, water bath Inner of SS outer powder coated finish with motorized stirrer to maintain desired temp. With cooling & heating arrangement controlled by a digital temp. Controller cum indicator with PT100 sensor, electrically operated plunger, penetration indicator and timing device. Digital penetrometer with digital timer coupled with Electrical plunger to measure the penetration in mm by digital penetration indicator in mm is also available in our stock.
...morePenetrometer
The Universal Penetrometer is employed for testing a wide variety of materials as measured by penetration of weighted needles or cones. Main applications are for bituminous materials, but waxes, greases, foods, and pharmaceuticals are among other products tested. Penetration is read from a 5" (127mm) diameter indicator dial of 0-400 divisions, each representing 0.1mm of penetration. Global offers heavy-duty units for manual and automatic use and a lighter, portable model for field work or for users with limited work load or limited budget. All meet ASTM and IS standards when fitted with proper needle or cone.
...morePARTICLE CHARGE APPARATUS
Unit consists of battery, rheostat, milliammeter, 2 - SS electrode plates, glass container, illumination for the chamber, timer device (all provided in required specified dimensions and parameters). Mains battery operated. The instrument is well illuminated with fluorescent lamp for better view of sample & deposition on SS plate. It operates on 12v supply either on mains battery through ON OFF switch. Digital power supply gives current greater than 4mA.A mechanical timer of 30Minutes Rating helps to set Time duration of deposit. ONE SPECIAL DIGITAL LED TO JUDGE ANIONIC CATIONIC WITH OUT CLEANING OBSERVATION OF SS PLATES provided
...moreOrbital Shaking Incubator
Use:- These units are designed for the growth of biological cultures & the shaking of the chemical solution Construction :- The unit comes with precise dynamically balanced shaking apparatus with microprocessor based PID temperature controller cum indicator with Pt- 100 sensor and digital timer with buzzer alarm for producing smooth rotating motion in 1” orbit. Heavy duty double wall incubation chamber with exterior made up of GI MS epoxy powder coat finish & interior of SS- 304. It is a vertical unit with magnetic gasket on the door to provide perfect sealing of the inside chamber. The door is fitted with a full-view polycarbonate acrylic sheet of 6 mm thickness for easy view of the inside chamber. The illumination of the chamber is by fluorescent lamp for easy viewing. The digital RPM indicator cum controller is provided with the speed range of 50 to 200 RPM with 25 mm orbit by PMDC motor. PUF insulation is provided between inner & outer walls. Interchangeable shaking platform can be given as option. Uniformity of temperature inside the camber is achieved through a flange mounted motorized blower from the back. The unit is also fitted with a special interlocking safety door switch for auto shut-off of shaking motor when the door is open. There is provision for two SS wire mesh trays at the top of incubator.
...moreOil Bath
Global 0nline oil bath are most useful for research & production application as a stability testing, conditioning, preheating & tempering. It is a double wall construction inner made of heavy gauge stainless steel chamber in one piece (for smaller capacity & argon welded for bigger size). Exterior is of aluminum dually powder coated finished with cerewool insulation in between two walls. A special long lasting heating element coupling type is easily replaceable is fitted with either thermostat or Digital temperature controller with PT—100 sensor. The single speed stirrer is provided for uniformity of temperature.
...moreMuffle Furnace
Double Decker type construction with muffles body at top & control box at bottom with 1"solid spacer in between Coil type Heater of Kanthal wire wounded on muffle with cerewool blanket &Brick insulation of 4" to have skin temp. of furnace less than 50 C Hinge door with lock system to openclose muffle Furnace. The control panel: At base of furnace with controller, stand by solid-state fuse with CrAl Thermocouple. Microprocessor based temperature controller cum indicator controls heating process.
...moreBe first to Rate
Rate This