Process Control Equipment Dealers in Kurla, Mumbai

Torque Controller Cable Reeling Drums are used for Heavy duty cables and where Cable length is more. i.e Gantry Cranes.

• Condition: New
• Brand Name: Yudo
• Voltage: 100 to 240 V AC
• Heat Resistance: 100 Degree C
• High Precise Measurement: +- 0.01 Degree C
• Precise Temperature Control: +- 0.018 Degree F
• Tolerance: +- 0.01 Degree C
• Model No.: CW662
• Temperature Range: 0
• Frequency: 50/60 Hz

• Type: Thermocouple Sensors
• Material: Plastic, Stainless Steel
• Application: Industrial
• Color: Black, Blue, Red, White
• Feature: Durable, Fine Finished, Good Quality, Light Weight, Rust Proof, Rust Resistance
• Condition: Good, New
• Power: 15w, 20w
• Warranty: 1year, 2years
• Condition: New, Used
• Alarm Range: 1.5mtr, 1mtr, 2.5mtr, 2mtr

we are offering PLC compatible vibratory feeder drive. RHY-101 is a thyristor phase angle control drive for vibratory feeders. its control is derived from a 4-20 ma analog input. RHY-101 is designed to respond from 0 to 99% for 4-20 ma input. however the actual vibratory response may start, anywhere from 10 -15 % and may saturate from 85 to 99 %. RHY-101 is housed in a panel or wall mounting enclosure 192mm (h), 48mm (w), 110mm (d). The wiring for the feeder coil, power supply (either 230v or 50v ac) and the low power control input are provided in two groups of pluggable screw termination.

• Important notes for installation: Cables must be fitted through 1/2" NPT cable gland or ATEX conduit (not supplied with instrument),Open cover only after de-energizing instrument Etc.

he ATEX approved Series AT2DH3 Digihelic® Differential Pressure Controller is a 3 in 1 instrument possessing a digital display gage, control relay switches, and a transmitter with current output. Combining these three features allows the reduction of several instruments with one product, saving inventory, installation time and money. The ATEX approved Digihelic® controller is the ideal instrument for hazardous area pressure, velocity and flow applications by allowing for the selection of pressure, velocity or volumetric flow operation in several commonly used engineering units. Two SPDT control relays with adjustable dead bands are provided along with a scalable 4 to 20 mA process output. In velocity or flow modes, a square root output is provided on the 4 to 20 mA signal to coincide with the actual flow curve. Flame-proof ATEX enclosures are available in aluminum and can include a glass window for viewing process information and set point status on digital display.

• Power: 230 VAC
• Control Type: On-Off
• Phase: Single Phase
• Frequency: 50 Hz
• RH: 10-95%, Non-condensing
• Temperature Range: 20 to 80 Degree Celsius

we are offering air bubble controller.performance and features: this instrument is install near size ring of plastic extraction machine to easy operating reducing air leakage, reduce size variation even through puncture reducing wastage in production, easy operating saving time.   technical specifications:   operation: - when film get puncture in bubble size will reduce so bubble air controller is automatic on & flow of air is start and stop when actual size is received which we have preset..

We specialize in offering highly efficient digital bell controller, which is acknowledged for its easy programmability. The digital bell controller basically allows control over the duration of the ringing of the digital bell. This digital bell controller is appreciated for its application in schools and colleges. This digital bell controller enables a clear bell ringing signal while ringing. why our digital bell controller? always rings the bell at right time every timeensures accurate control over bell systemmaintains the real time bell time even during power failurescustom designed and installed as per the specific institution’s requirements

• Supply Ability: 20 Piece/Pieces per Month
• Place of Origin: Maharashtra, India
• Port: Nhavasheva
• Packaging Details: Wooden Box

• Features: Exact dimensions,Reliable,Precise

Resistance Temperature Detectors (RTD’s) are temperature sensing devices consisting of a wire coil or deposited film of pure metal, usually platinum. The element’s resistance increases with temperature in a known and repeatable manner. RTD’s exhibit excellent accuracy over a wide temperature range. Non standard size can be manufactured on request.

TEMP TECH manufacturers Resistance Temperature Detectors (RTD’s) confirming to all international Standards like IEC 751 , GOST, BS-1904, DIN 43760, JIS C1604, 1606 etc…. All types of configurations are available and most of the RTD’s are custom made. Accuracy in measurement of Temperature, faster response, sturdiness, ease in maintenance and replacement are the main criteria of design.

One of the strongest heads on the market with a payload of 50kg (110 lbs), making it suitable for 3D camera rigs Zero backlash, no delay unlike ordinary worm gear drives High resolution drive for smooth operation and crisp responsiveness Quick set-up due to a unique plug & play design and simple Mo-Sys bus cabling system Simple, intuitive touchscreen control Unrivalled ease of adjustment Can be underslung, getting the lens closer to the floor than a geared head. With the slip ring fitted option, the Lambda head is capable of continuous, multi-turn 360 degree rotation in all axes without the worry of cable wraps.

• Type: Simplex and duplex.
• Insulation of cables: 7/32 Teflon, Teflon/Teflon, Insulated.
• Type of cable: 2 core, 3 core, 4 core and 6 core.
• SS rod: 316 stainless steel material with 8mm diameter
• Mounting parts: 1/8 BSP, 1/4 BSP, 1/2 BSP and 3/8 BSP and without threading.
• Head: Aluminum with powder coated.
• Terminal: 2 or 3 wires for simplex , 4 or 6 wires for duplex
• SS rod: 316 stainless steel material with 8mm diameter
• Mounting parts: 1/8 BSP, 1/4 BSP, 1/2 BSP and 3/8 BSP and without threading

We manufacture different types of temperature sensors as per the specifications of the customer by using PT100 sensing element and maintain international quality. The element of PT100 sensors has been imported from Germany and the SS rod is made up of 316 stainless steel material, which enables it to withstand a high pressure vessel. The sensor has been designed in such a manner that it is well suited for temperature measurement in any industrial environment, especially around motors, generators and other high voltage equipment. The range of the PT 100 sensor varies from 0-400 degree.

Standalone, Lube Fuel Oil Oil Contamination Deterioration Monitor has no moving parts , temperature compensated , one touch calibration, with two level alarm set points , Low Flow detection and Metallic dust (bearing metalmill scale etc) detection . Extremely easy & simple installation. Prevent Major breakdowns . Can be used with Diesel Engines, Turbines, Hydraulic Cranes, Separators Transformers etc. Contact us for a complete engineered solution.

The company has gained trust of the clients by manufacturing and supplying the best quality Water Level Controller. Water Level Controller has number of automatic features which set the operator free from operating the pump and save overflowing of water and electricity. Further, the international designing and structure of Water Level Controller is widely appreciated. Working :The water level controller {WLC} first checks underground water in the underground tank to the predefined upper level. Once the predefined upper level is achieved in the underground tank and if the overhead tank is empty (below predefined lower level) then the WLC switches on the pump. Whenever the pump starts, just after a minute the WLC checks the water flow. If the water flow is not achieved then the WLC gives the Dry Run audio visual indication and stops the pump. This saves the pump from dry running and saves electricity. Similarly when the water flow is sensed then the WLC checks the levels of water in the underground tank as well as overhead tank simultaneously. Once the water in the overhead tank fills up to the predefined upper level or the water is pumped below the predefined lower level in the underground tank the pump is switched off automatically. The WLC takes feedbacks from the float sensors and checks the levels of water in the overhead tank as well as the underground tank regularly. Similarly when the overhead tank gets empty, the WLC starts the pump provided there is enough water in the underground tank.Key Specifications : Dimension’s - W: 125mm H: 180mm D: 62mm. Power Supply – 230 Volt AC 50Hz. Power consumption – 6 Watts Advantages of float sensors : Sensor is enclosed in water proof capsule. As no electric supply in water so no electrolysis. Doesn’t require cleaning. Lifelong with free maintenance. High accuracy. Works on low voltage. Less power consumption.  

High quality standards in production and storage necessitate a comprehensive monitoring system that delivers measured data reliably. The adaptive RMS Rotronic Monitoring System is the perfect solution for a wide range of applications.

TEMP TECH manufacturers Resistance Temperature Detectors (RTD’s) confirming to all international Standards like IEC 751 , GOST, BS-1904, DIN 43760, JIS C1604, 1606 etc…. All types of configurations are available and most of the RTD’s are custom made. Accuracy in measurement of Temperature, faster response, sturdiness, ease in maintenance and replacement are the main criteria of design.

We are engaged in trading of optimum quality Satronic (Honeywell) Sequence Controller for Safe and efficient operation of the burner. These can be offered to our clients in customized specifications as per their varied requirements.   Our range includes the following Oil Burner Sequence Controllers : TF 801, TF 802, TF 804, TF 832, TMO 720 Gas Burner Sequence Controllers : TFI 812, MMI 811/ 812/813, MMG 810/ 811, TMG 740 Flame detectors : FZ 711, MZ 770, IRD, UVZ 780, UVD 970, UVD 971

• Type: Speed Controller
• Color: Black, Green
• Voltage: 110vdc, 12vdc, 220vdc
• Frequency: 15hz, 50hz
• Material: ABS, Mild Steel, PVC
• Power: 1-3kw, 3-6kw, 6-9kw
• Power Source: Electric
• Phase: Double Phase, Single Phase, Three Phase
• Warranty: 1year, 2years

Features: Auto or Manual Function PID Auto Temperature Control Soft Start up - 94 deg Celcius Heater on Indicator Selectable two thermocouple types (J/K) Thermocouple Break Msg TC Open / op% Specifications: Dimension : W-50 H-176 D-192MM Power Input : 15AMP 230VAC =/- 15% Power Frequency : 50 / 60 Hz PV Temperature : +/- 2 deg Celcius

Control Technology for Hot Runner Systems: Safe and Comfortable 1, 2, 3, 5-channel temperature controllers DP1, DP2The compact controllers for economical and comfortable control of small hot runner systems. Total connected value 1-phase 230 V 16 A Fuzzy PID control behaviour Set / actual display for each control point Gentle softstart function Pulse group control Power limitation Temperature reduction during production breaks Regulated operation in case of failed thermal probe possible Counter for hours of operation Continual error monitoring   Multi-channel temperature controllers DPT5, DPT10, DPT15, DPT20, DPT45The multiple controllers of the DPT series offer extensive functions for the safe control of complex hot runner systems. Four selectable temperature programs Fuzzy PID control behaviour Gentle softstart function Control-TechnologySet/actual display for each control point Limited power during start-up Start-up ramp for even heating of different heating circuits Phase control and pulse group control Temperature reduction during production breaks possible Regulated operation in case of failed thermal probe possible Diagnostic function for detection of wiring errors Up to 3500 W per control zone Counter for hours of operation Continual error monitoring Connectors of thermocouples and heating elements physically separated Retrofitting of up to 15 control zones is feasible Optional with serial interface for connection of injection moulding machines by ARBURG, ENGEL, KRAUSS-MAFFEI, FEROMATIK, etc.   Multi-channel temperature control cabinet DPT multi zone for operation with multiple tools with a high number of cavities. This new development especially for the operation of multiple tools with a high number of cavities offer a comprehensive range of functions: Expandable from 40 up to 150 control circuits (in steps of 5), the LCD touch-screen display guarantees the simplest operation for highly complex tools. The control is executed by means of a Windows software. Graphic tool display with freely moveable display fields. Full-text error messages. Log files for monitoring errors and status. Possibility of managing two tools separately. Print function for temperature records. Various remote maintenance possibilities via standard PC interfaces.     Controller eValve-4The controller "eValve-4" is able to control up to four bistable electromagnets, which are used for nozzles with needle valve. The electrical lift magnets generate a mechanical lift of 10 mm. The two end position are fixed with permanent magnets. Electric power is only used for changing the position of the magnetic fixed lifting cylinder.

• FS pressure ranges: 6 000 psi (415 bar) or 10 000 psi (700 bar)

The Model 7350 high pressure pneumatic controller provides a safe, easy to use and effective means of automating high pressure test and calibration of a wide range of pressure measuring devices. In control mode, these controllers simultaneously measure and control pressure, and can be used for the calibration and testing of pressure gauges, transducers, pressure switches and production pressure instruments.

• Driven Type: Electric
• Condition: New
• Automatic Grade: Automatic
• Application: Controls Water Level

Offers temperature indicator.

electronic process control instruments, Digital Temperature Indicator

process controls equipments, Automation Products, flow measurement

Streaming Current Controller, bi-mwa light scattering detectors

TEMPERATURE, bank bead, electrical sensors, Electronic Components