Spiral Gaskets Dealers in Fort, Mumbai

• Spiral Wound Gaskets: ring type joints
• metallic ring: semi metallic corrugated flange gaskets

We manufacture and supply spiral wound gaskets, Ring type joint, Metallic ring, Semi metallic corrugated flange gaskets etc.

SHASON Spiral Wound Gaskets are semi metallic products designed for high pressure and temperature applications. A variety of forms of the gasket are available and these can be manufactured in various materials or sizes to suit your requirement. With over thousands of satisfied customers who have procured SHASON spiral wound gaskets, we are confident that we can meet all your service requirements.

Spiral Wound Gaskets are composed of a metallic continuous stripe with a special shaped profile, coupled with a continuous filing stripe (Asbestos, PTFE, Grafoil, Ceramic etc) evenly wound in concentric spiral under constant stress. Spiral Wound Gaskets are reinforced on the inner and outer diameter by winding of several electrically welded spiral metals only. The main property of Spiral Wound Gasket, owing to elastic action of the special metallic stripe profile, is that of offering a perfect sealing under all fluctuating pressure and temperature conditions, also where temperature excursion has considerable value, maintaining tightening elastic recovering. This elasticity can be modified by a proper selection of components, and they can be installed even with flanges at standard working with lightly pitted or buckled by the use of flanges. A proper selection of materials (both metal and fillers) allows to adequate the spiral gasket to the most various operating conditions. gasket, head, car, exhaust, cylinder, manifold, engine, seal, material, rubber, oil, valve, sheet, repair, seals, metal, sealing, neoprene, silicone, epdm, materials, manufacturers, supplier, ptfe, spiral wound, graphite, CAF, O ring, packing, mechanical, industrial, high temperature, etc

We manufacture and supply best quality of Spiral wound gaskets which have proven themselves as highly effective sealing element for use in difficult, critical and arduous duties. Our Spiral wound gaskets are popular in various industries like Petrochemical, Chemical, Steam lines and Process Industries, where they have many advantages over older types of gaskets. We can manufacture Spiral Wound Gaskets with different filler like Graphite/Asbestos/PTFE/CAF etc. Also, we can provide different winding material.

INSEAL Spiral Wound Gaskets are semi metallic products designed for high pressure and temperature applications. A variety of forms of the gasket are available and these can be manufactured in various materials or sizes to suit your requirement. With over thousands of satisfied customers in India and around the world who have procured INSEAL spiral wound gaskets, we are confident that we can meet all your service requirements How they work The sealing element of the spiral wound gasket consists of a V-shaped metal strip spirally wound in combination with a soft sealing material as a filler. The metal strip provides outstanding resilience, while the flexible sealing filler guarantees excellent sealing. Due to this combination of materials, the spiral wound gasket is suitable for sealing under severely fluctuating temperature and pressure conditions. Depending on the application the spiral wound gasket can be specified with outer and/or inner rings.   Properties Spiral Wound Gaskets are suitable for use across a wide range gasket stress range Spiral Wound Gaskets can be used to seal fluid pressures up to 400 bar and from cryogenic temperatures up to 1000oC Spiral Wound Gaskets are robust and simple to install The outer guide ring simplifies assembly and prevents blow-out of gasket By combining different winding materials and metals, the gasket can be tailored to suit a wide variety of operating conditions The gasket is easy to remove after service and does not cause any damage to the flange faces   How to Order Please specify the following when ordering Spiral Wound Gaskets. Type of Spiral Wound Gasket required Standard of the gasket (flange standard) Nominal size and pressure class Gasket Thickness Quantity Material Inner Ring Metal winding Filler Outer Ring   Hints Of Installation & Maintenance When installing a Spiral Wound Gasket, check the dimensions of the Gaskets for use between pipe and pressure vessel flanges. The procedure is as follows Measure ID of flange contact face. Measure Gasket ID. If Gasket ID is not 1/8″ larger than flange ID,  do not use it unless it can be installed perfectly centered. A Spiral Wound Gasket does not have the same feel as other Metallic or Non-Metallic Gaskets during the bolting-up. It’s different-because it gives a little bit under each bolt as it is tightened. It is therefore important to tighten the bolts in small steps in proper sequence as shown hereunder. Final tightening must be uniform with each bolt pulling same load. This will guarantee a trouble free joint. If not uniform, the joint may leak-particularly after it has been in hot service. Tighten the bolts after 24 hours and again a week later.

We offer precisely engineered spiral wound metallic gaskets that are widely used with flanges through which liquids are passed at high temperature. These metallic gaskets effectively prevent leakages in flanges owing to their spiral construction.

• Size: 10-20inch, 20-30inch, 30-40inch, 40-50inch
• Type: Spiral Wound Gasket
• Material: Rubber
• Thickness: 10-20mm, 20-30mm, 30-40mm, 40-50mm
• Application: Electric Use, Fittings Use, Industry Use, Toy Making
• Color: Brown, Dark Black, Grey, Grey-black, Silver, White
• Feature: Durable, Fine Quality, High Strength, Perfect Shape, Rust Proof, Strong Construction, Superior Finish
• Condition: New, Used
• Finishing: Non Polished, Polished
• Temperature: 0-50 ℃, 50-100 ℃

• Shape: Round
• Feature: Excellent Compression,Temperature & Pressure Resistance,Nominal Price Range

Spiral wound gasket (SWG) consists of thin metal hoop and nonmetal filler material that are simultaneously wound. The metal hoop is pre-formed in V or W shaped profile, which allows the gasket to act as a spring between the flanges. The hoop also provides the basic structural element for the gasket while the nonmetal filler material seals the flange surfaces that are with small imperfections.Depending on its excellent compression resilience, it is suitable for sealing spots where the alteration of temperature and pressure are frequent. It can be used as the static sealing element of pipe, valve, pump, thermal exchange, condensing tower, plain hole and man hole of flange, etc. It has been widely applied in the fields of petrochemical, mechanical manufactory, power station, metallurgy, shipbuilding, pharmaceutical, nuclear power station and navigation, etc   Application Available in a full range of styles and materials, our spiral-wound gaskets are manufactured in accordance with ASME B 16.20 for use in all industry flanges, including ASME B16.5 and ASME B 16.47, Series A&B. Leader GT assures strict adherence to these specifications as routine inspectionprocedures are applied throughout the manufacturing process. In addition, we maintain traceability of all materials used in our gasket construction to provide material certifications as required

  Special Springlike Metal strips are wound with an Asbestos/Asbestos-Free P.T.F.E/Grafoil Filler by a special process to assure a leakproof seal. The sealing is done by the Heat Resistant Filler and the metal strip provides the spring. This combination of metal and soft Heat Resistant Filler piles compresses to its predetermined thickness under bolting pressure and thereby prevents leakage within the limit of its specified pressure and temperature. With the addition of centering devices, "CHAMPION" Spiral Wound Gaskets can be adapted for use on many types of flanges and closures. 

PTFE Packing, Fireproof Document Bag, Adhesive Graphite Tapes

polycarbonate spiral wound ring joint gaskets, ptfe lining, Pvc Rods

Rubber Flooring Sheet, Nylon Pad, Cast Nylon Pipes, Nylon Sheet

Ball Bearings, DOUBLE OPEN ENDED SPANNER, Hammer, high tensile allen bolt

Gland Packing Material

exchanger gaskets, Ring Type Joint Gaskets, Solid Metal Gaskets

PTFE Product, Metal Jacketed Gaskets, glass fiber product, Ceramic Product