Sump Pump Dealers in Mumbai

We are a reputed manufacturer, exporter and supplier of cantilever sump pump. A cantilever shaft pump generally utilizes rolling element bearings to support an overhung shaft that extends downward into a sump or tank. The bearings are mounted above the maximum liquid level so that they are never exposed to the pumped fluid. Because there are no submerged bearings, the pump handles solids without the need for external flush, or any sealing devices, to keep the pumped fluid out of the support column. Cantilever pumps may also be operated dry, or with loss of prime, without damage. cantilever pumps require no seals or packing when used on open sumps. When applied to closed tanks with hazardous materials, the rolling element bearings limit shaft run-out so that mechanical seals may be applied reliably. with the exception of a few special cases, the shaft and bearing assembly of a cantilever pump is designed so as to operate below 1st lateral critical speed1. As the amount of shaft overhang increases, the shaft diameter is increased so as to provide sufficient stiffness to limit deflection and provide rotor stability. The design diameter of the shaft is a function of the length of the shaft overhang, the rotational speed, and the mass of the impeller. Typically, the practical maximum shaft diameter is about eight inches. Above this diameter, conflicts with bearing speed and load ratings start to occur. This diameter equates to a maximum overhung distance of somewhere between six and eight feet for most pumps. the lowest speed at which the natural frequency of the shaft is synchronized with the operating speed. Critical speed is characterized by very high vibration levels. Designing below 1st critical speed provides for smooth operations under all ‘good practice’ operational conditions. the maximum lift is very design and application dependent. On certain designs the maximum lift can be extended to about 20 feet. The trade-offs with increasing the maximum lift capability is with efficiency and axial thrust.

•  :  
• Weight (Kg): 16
• Air Consumption (m3/min): 2.63
• Hose size (mm): 19
•  :  
• Fluid Inlet Hose Size: screen
• Fluid Outlet Hose Size: 2"NP

We design and manufacture the industrial sump pumps to handle various type of fluids from drainage water or any liquid waste containing non-fibrous solids to larger industrial processes. This model is available in various types of materials and configurations for various types of industries. It can be configured for suspension plate or self supporting stand. These sump and condensate application pumps are available with high thrust bearing for temperatures over 200 degrees Fahrenheit. These pumps are available in 1.5 inches to 8 inches discharge sizes and flow rate upto 1600 GPM. Features:   Adjustable impeller, Leak proof, Vapor tight construction, Extensions for pit depths from 2 to 20 feet.   Applications:   Sump drainage, Industrial process, Elevator pits, Basements, Power plants, Flood control, Storm water, Condensation control, General dewatering service.

• Type: Sump Pump
• Application: Ground Water Supply
• Color: Blue, Green, Grey, Orange, Red, White, Yellow
• Voltage: 110V, 220V, 380V
• Fuel: Electric
• Pressure: 0-10bar, 10-20bar, 20-30bar, 30-40bar
• Warranty: 1 Year, 2 Years, 5 Years
• Condition: New, Used

• Features: Zero maintenance pumps, eliminates the need for gland packing and seal, Leak proof and can run dry without damage of rotating parts, Pump is seal less hence can run dry, Preferred selection for E.T.P. plant because of seal less design

• Material: Metal
• Temperature Range: Up to 120 Degree C
• Outer Dia: NB 25 to 300 mm
• Specific Gravity: 0.75 to 1.5 g/cm3
• Capacity: 500 M3/hr
• Surface Finishing: Color Coated
• Features: Long service life, Rugged, High performance

Teryair Submersible pump has a small cross-section and can be lowered into areas having small access hatches. Especially preferred where and eclectic spark may risk ignition or explosion.       Features Will pump down to 22mm will handle up to 3mm solids governor controlled motor compact design enables uses in restricted areas. Air inlet operated by gate valve lever.

• Suction Size: Up to 200 mm
• Capacity: Up to 400 m³/hr (6,600 LPM)
• Head: Up to 60 mts.
• Material of Construction: C.I. / Ni C.I. / Ni Hard / C.S. / SS-304 & 316 / SS-316 L / Alloy-20

Single Stage Vertical Centrifugal pumps mounted on heavy duty surface plates. These pumps are suitable for handling liquids from wet and dry pits up to 5 mts. sump depths. Features Available with: Special line bearings for low vibration and longer life Semi-open impellers for pumping slurries / sludges Mechanical seals for pumping chemicals & petrochemicals Generally conforming to API 610 specifications Applications Light petroleum products Industrial waste Sludges / Slurries / Sewage Chemicals

• Country of Origin: Made in India
• Type: Electric
• Number Of Stages: Single-stage Pump
• Motor Phase: Three Phase
• Brand: LUBI
• Motor Horsepower: 150 HP

Vertical Sump Pumps, air diaphragm pump, Submersible pumps, hand pumps

sump pump, Variable Speed Drive, sludge pump, Paving Breaker, Clay Digger

sump pump, Air Operated Double Diaphragm Pump, Chemical Pump

sump discharge pump

sump pump, Car Paint Booth, Industrial Piston Compressor

sump pump, Air Compressors, Grinder, Chipping Hammer

VERTICAL MOLTEN SULFUR SUMP PUMP, Horizontal Chemical Process Pump